wheatstone bridge. able to count the voltage once resistor changed.
标签： wheatstone resistor changed voltage
上传时间： 2014-01-27
上传用户：zhuimenghuadie
I2C driver for PIC, PICC compiler - bitbanged. Needs pull-up resistor on SCK and SDA and ports set for open collector
标签： bitbanged and compiler resistor
上传时间： 2017-07-01
上传用户：yzhl1988
Abstract: A laser module designer can use a fixed resistor, mechanical pot, digital pot, or a digital-to-analogconverter (DAC) to control the laser driver's modulation and bias currents. The advantages of a programmablemethod (POT or DAC) are that the manufacturing process can be automated and digital control can be applied(e.g., to compensate for temperature). Using POTs can be a more simple approach than a DAC. There can be aslight cost advantage to using a POT, but this is usually not significant relative to other pieces of the design.Using a DAC can offer advantages, including improved linearity (translating to ease of software implementationand ability to hit the required accuracy), increased board density, a wider range of resolutions, a betteroptimization range, ease of use with a negative voltage laser driver, and unit-to-unit consistency
上传时间： 2013-11-13
上传用户：ca05991270
Abstract: Transimpedance amplifiers (TIAs) are widely used to translate the current output of sensors like photodiode-to-voltagesignals, since several circuits and instruments can only accept voltage input. An operational amplifier with a feedback resistor fromoutput to the inverting input is the most straightforward implementation of such a TIA. However, even this simple TIA circuit requirescareful trade-offs among noise gain, offset voltage, bandwidth, and stability. Clearly stability in a TIA is essential for good, reliableperformance. This application note explains the empirical calculations for assessing stability and then shows how to fine-tune theselection of the feedback phase-compensation capacitor.
标签： Transimpedance Stabilize Amplifier Your
上传时间： 2013-11-13
上传用户：daoyue
LAYOUT REPORT .............. 1 目錄.................. 1 1. PCB LAYOUT 術語解釋(TERMS)......... 2 2. Test Point : ATE 測試點供工廠ICT 測試治具使用............ 2 3. 基準點 (光學點) -for SMD:........... 4 4. 標記 (LABEL ING)......... 5 5. VIA HOLE PAD................. 5 6. PCB Layer 排列方式...... 5 7.零件佈置注意事項 (PLACEMENT NOTES)............... 5 8. PCB LAYOUT 設計............ 6 9. Transmission Line ( 傳輸線 )..... 8 10.General Guidelines – 跨Plane.. 8 11. General Guidelines – 繞線....... 9 12. General Guidelines – Damping resistor. 10 13. General Guidelines - RJ45 to Transformer................. 10 14. Clock Routing Guideline........... 12 15. OSC & CRYSTAL Guideline........... 12 16. CPU
上传时间： 2013-12-20
上传用户：康郎
Abstract: We can apply a BiCMOS integrated circuit with only resistors and no transistors to solve adifficult design problem. The mythically perfect operational amplifier's gain and temperature coefficient aredependent on external resistor values. Maxim precision resistor arrays are manufactured together on asingle die and then automatically trimmed, to ensure close ratio matching. This guarantees that theoperational amplifier (op amp) gain and temperature coefficient are predictable and reliable, even withlarge production volumes.
上传时间： 2014-11-30
上传用户：ynzfm
精确度0.05%满刻度±1位数（Accuracy 0.05%F.S.±1digit） 可测量交直流电流/交直流电压/电位计/传送器/Pt-100/荷重元/电阻等信号（Measuring DCA/DCV/ACA/ACV/Potentiometer/Transmitter/Pt-100/Load Cell/resistor/etc……） 显示范围0-19999可任意规划（Programmable rate 0 to 1999 digit） 小数点可任意规划（Decimal point can be modified） 尺寸小，稳定性高（Dimension small & High stability）
上传时间： 2014-01-25
上传用户：RQB123
Abstract: A resistive feedback network is often used to set the output voltage of a power supply. A mechanical potentiometer (pot)conveniently solves the problem of adjusting a power supply. For easier automatic calibration, a mechanical pot can be replaced witha digital pot. This application note presents a calibration solution that uses a digital pot, because digipots are smaller, do not movewith age or vibration, and can be recalibrated remotely. This proposed solution reduces the susceptibility of the system to thetolerance of the digital pot's end-to-end resistance, making the solution optimal fordesigners. This application note also explainssome of the equations required to calculate the resistor chain values and to use a digital pot in this way. A spreadsheet withstandard reisistor values is available for easy calculations.
上传时间： 2013-10-31
上传用户：caiguoqing
The CN3052A is a complete constant-current /constant voltage linear charger for single cell Li-ion and Li Polymer rechargeable batteries. The device contains an on-chip power MOSFET and eliminates the need for the external sense resistor and blocking diode.
上传时间： 2013-11-10
上传用户：子虚乌有
高的工作电压高达100V N双N沟道MOSFET同步驱动 The D810DCDC is a synchronous step-down switching regulator controller that can directly step-down voltages from up to 100V, making it ideal for telecom and automotive applications. The D810DCDC uses a constant on-time valley current control architecture to deliver very low duty cycles with accurate cycle-by-cycle current limit, without requiring a sense resistor. A precise internal reference provides 0.5% DC accuracy. A high bandwidth (25MHz) error amplifi er provides very fast line and load transient response. Large 1Ω gate drivers allow the D810DCDC to drive multiple MOSFETs for higher current applications. The operating frequency is selected by an external resistor and is compensated for variations in VIN and can also be synchronized to an external clock for switching-noise sensitive applications. Integrated bias control generates gate drive power from the input supply during start-up and when an output shortcircuit occurs, with the addition of a small external SOT23 MOSFET. When in regulation, power is derived from the output for higher effi ciency.
上传时间： 2013-10-24
上传用户：wd450412225
