Special picture button, easy configure... release. You only need one picture for pressed and one for normal state.
上传时间： 2014-08-26
上传用户：c12228
simple mouse pressed, clicked, dragged test applet.
标签： clicked dragged pressed simple
上传时间： 2017-04-22
上传用户：busterman
·详细说明：C++写的DTMF算法，内含一个pcm数据文件，读入文件并分析按键-c writes the DTMF algorithm, contains a pcm data file, the read-in document and the analysis pressed key。文件列表: DTMF ....\DTMF.cpp ....\DTMF.
上传时间： 2013-04-24
上传用户：Miyuki
5 ledblink -- 跑马灯程序 该项目在SDT2.51下编译调试。最简单的demo程序，运行后3个发光二极管轮流点亮。 6 timerint -- 定时器中断demo程序 该项目在SDT2.51下编译调试。将子目录timerint拷贝到c:\ 下。 该demo程序的主程序是while空循环，定时器中断服务程序每500ms将3个LED反相。 在57600超级终端里也可以看到中断发生时的信息。 7 uart -- 串口测试程序 该项目在SDT2.51下编译调试。运行后在57600的超级终端里等待PC键盘的输入，当按下 a 或 b 或 c 按键时，超级终端里将显示 You pressed a ,You pressed b ,You pressed c .
上传时间： 2015-05-05
上传用户：aix008
* KeyDebounce Accept new key reading, handle timing for debounce & slew * KeyId Report which key is currently pressed * KeySlewTimeSet Accept slew time for key currently pressed
标签： KeyDebounce key debounce reading
上传时间： 2013-12-17
上传用户：妄想演绎师
The aim of this application note is to show to scan the 4x4 matrix keypad multiplexed with a four 7-segment display. The software attached to this application note scans the pressed key and displays it on the multiplexed 7- segment LEDs. This application note makes obvious Interrupt capability of the STR710 device to offer a better key scan .
标签： application multiplexed matrix keypad
上传时间： 2015-09-13
上传用户：thuyenvinh
This will sample all 8 A/D-channels. The result will be send out via UART1 and can be seen within any terminal-program (9600 Baud). With each pressed key the next channel will be converted. No interrupts are used.
标签： will D-channels sample result
上传时间： 2016-04-23
上传用户：wxhwjf
This file is distributed in the hope that it will be useful, but WITHOUT WARRANTY OF ANY KIND. Author(s): Ole Saether DESCRIPTION: This example should be used together with ex2a-tx433.asm. One nRF9E5 evaluation board (receiver) should be programmed with the hex-file generated from assembling this file and the other evaluation board (transmitter) programmed with the hex-file generated from assembling ex2a-tx433.asm. All switches on the DIP-swith S206 on the receiver must be set to the "on" position and all switches on the DIP-swith S205 on the transmitter must be set to the "on" position. When one of the switched SW1-SW4 on the transmitter is pressed the corresponding LED on the receiver is turned on. The functionality is the same as in ex2c-rx.c.
标签： distributed WARRANTY WITHOUT useful
上传时间： 2017-05-17
上传用户：xieguodong1234
/* * tesswind.c * This program demonstrates the winding rule polygon * tessellation property. Four tessellated objects are drawn, * each with very different contours. When the w key is pressed, * the objects are drawn with a different winding rule. */
标签： demonstrates tessellation tesswind program
上传时间： 2013-12-10
上传用户：星仔
