电力电子技术介绍
标签： Applications Electronics Converters Design
上传时间： 2013-10-30
上传用户：1142895891
简单介绍了三相SPWM逆变器的组成和工作原理，通过计算机对三相SPWM逆变器进行Matlab/Simulink建模和仿真，研究逆变电路的输入输出及其特性。仿真分析经逆变后得到的电压电流的特性。通过运用Matlab/Simulink和Power System Block（PSB）电力系统模块集工具箱仿真环境，对电路进行建模、计算和仿真分析。MATLAB软件中的Simulink，是为数不多的完全满足这些条件和要求的软件。并且凭借他在科学计算方面的天然优势建立了从设计构思到最终实现设计要求的可视化桥梁。被广泛应用于线性系统、非线性系统及数字信号处理的建模和仿真中。
上传时间： 2013-11-12
上传用户：yulg
We provide complete power solutions with a full lineup of power managementproducts. This brochure provides an overview of our high performance DC/DC switching regulatorcontrollers for applications including datacom, telecom, industrial, automotive, medical, avionicsand control systems. We make power design easier with our industry-leading field applicationengineering support; a broad selection of demonstration boards with schematics, layout filesand parts lists; SwitcherCAD® software for simulation, application notes and comprehensivetechnical documentation.
上传时间： 2013-10-15
上传用户：lz4v4
In industrial applications, high voltage power supply spikes with durations ranging from a few microseconds to hundreds of millisecondsare commonly encountered. The electronics in these systems must not only survive transient voltage spikes, but in many cases alsooperate reliably throughout the event.
上传时间： 2013-11-07
上传用户：redmoons
返驰式(Flyback) 电源供应器是交换式电源设计供应器(Switch Power Supply，SPS)的一种，为工业界常用之电路架构，其特点如下表所示，图一所示为返驰式转换器(Flyback Converter)电路。 一般设计SPS需要一些保护来提高系统设备之稳定安全，尤其是输出过电压保护极为重要，这个输出过电压保护目的是防止电气设备上的元件之绝缘遭受过电压的破坏。一般过电压的测试方法是将回授Open让系统呈现段回路状况，导致一次侧能量无限制提供给二次测来达到输出过电压现象。
上传时间： 2013-11-06
上传用户：haoxiyizhong
计算机的ATX电源脱离主板是需要短接一下20芯接头上的绿色（power on）和黑色（地）才能启动的。启动后把万用表拨到主流电压20V档位，把黑表笔插入4芯D型插头的黑色接线孔中，用红表笔分别测量各个端子的电压。楼上列的是20芯接头的端子电压，4芯D型插头的电压是黄色＋12V，黑色地，红色＋5V。 主板电源接口 图解 20-PIN ATX主板电源接口
上传时间： 2013-10-28
上传用户：蒋清华嗯
Abstract: This application note illustrates an intermediate 8V switching power supply for an automotive radio and infotainment system.The design withstands the complete automotive input voltage range (including cold crank and load dump conditions), assuring a stable8V supply for common subsystems such as a CD driver, LCDs, and a radio module in modern infotainment systems. To avoiddisturbance in the AM and FM bands, the switching power supply runs at a fixed frequency of 2MHz, enabling an ideal solution forradio systems.
上传时间： 2013-11-20
上传用户：feitian920
Abstract: We don't expect manufacturers to produce clothes that in one size that fits everyone. In thesame way, one ESD component can't solve all issues—each application has different ESD requirements.Knowing that "one size fits all" cannot apply to power design, the power designer, or the engineering"super hero," must consider all the potential disruptions to a steady flow of power and thenvarious waysto mitigate them. This tutorial describes voltage- and current-limiting devices and risetime reducers tomanage the power. It also points to free and low-cost software tools to help design lowpass filters, checkcapacitor self-resonance, and simulate circuits.
上传时间： 2013-11-18
上传用户：zhouxuepeng1
Abstract: Impedance mismatches in a radio-frequency (RF) electrical transmission line cause power loss andreflected energy. Voltage standing wave ratio (VSWR) is a way to measure transmission line imperfections. Thistutorial defines VSWR and explains how it is calculated. Finally, an antenna VSWR monitoring system is shown.
上传时间： 2013-10-19
上传用户：yuanwenjiao
Abstract: This document details the Oceanside (MAXREFDES9#) subsystem reference design, a 3.3V to 15V input,±15V (±12V) output, isolated power supply. The Oceanside design includes a high-efficiency step-up controller, a36V H-bridge transformer driver for isolated supplies, a wide input range, and adjustable output low-dropout linearregulator (LDO). Test results and hardware files are included.
上传时间： 2013-10-12
上传用户：jinyao
