为了在CDMA系统中更好地应用QDPSK数字调制方式，在分析四相相对移相（QDPSK)信号调制解调原理的基础上，设计了一种QDPSK调制解调电路，它包括串并转换、差分编码、四相载波产生和选相、相干解调、差分译码和并串转换电路。在MAX+PLUSⅡ软件平台上，进行了编译和波形仿真。综合后下载到复杂可编程逻辑器件EPM7128SLC84-15中，测试结果表明，调制电路能正确选相，解调电路输出数据与QDPSK调制输入数据完全一致，达到了预期的设计要求。 Abstract: In order to realize the better application of digital modulation mode QDPSK in the CDMA system， a sort of QDPSK modulation-demodulation circuit was designed based on the analysis of QDPSK signal modulation-demodulation principles. It included serial/parallel conversion circuit, differential encoding circuit, four-phase carrier wave produced and phase chosen circuit, coherent demodulation circuit, difference decoding circuit and parallel/serial conversion circuit. And it was compiled and simulated on the MAX+PLUSⅡ software platform,and downloaded into the CPLD of EPM7128SLC84-15.The test result shows that the modulation circuit can exactly choose the phase，and the output data of the demodulator circuit is the same as the input data of the QDPSK modulate. The circuit achieves the prospective requirement of the design.
上传时间： 2014-01-13
上传用户：qoovoop
The Tri-Mode Ethernet MAC (TEMAC) UltraController-II module is a minimal footprint,embedded network processing engine based on the PowerPC™ 405 (PPC405) processor coreand the TEMAC core embedded within a Virtex™-4 FX Platform FPGA. The TEMACUltraController-II module connects to an external PHY through Gigabit Media IndependentInterface (GMII) and Management Data Input/Output (MDIO) interfaces and supports tri-mode(10/100/1000 Mb/s) Ethernet. Software running from the processor cache reads and writesthrough an On-Chip Memory (OCM) interface to two FIFOs that act as buffers between thedifferent clock domains of the PPC405 OCM and the TEMAC.
上传时间： 2013-10-26
上传用户：yuzsu
This is the Xilinx Dual Processor Reference Designs suite. The designs illustrate a few differentdual-core architectures based on the MicroBlaze™ and PowerPC™ processors. The designsillustrate various concepts described in the Xilinx White Paper WP262 titled, “DesigningMultiprocessor Systems in Platform Studio”. There are simple software applications includedwith the reference designs that show various forms of interaction between the two processors.
上传时间： 2013-10-29
上传用户：旭521
在研究传统家用燃气报警器的基础上，以ZigBee协议为平台，构建mesh网状网络实现网络化的智能语音报警系统。由于传感器本身的温度和实际环境温度的影响，传感器标定后采用软件补偿方法。为了减少系统费用，前端节点采用半功能节点设备，路由器和协调器采用全功能节点设备，构建mesh网络所形成的家庭内部报警系统，通过通用的电话接口连接到外部的公用电话网络，启动语音模块进行报警。实验结果表明，在2.4 GHz频率下传输，有墙等障碍物的情况下，节点的传输距离大约为35 m，能够满足家庭需要，且系统工作稳定，但在功耗方面仍需进一步改善。 Abstract: On the basis of studying traditional household gas alarm system, this paper proposed the platform for the ZigBee protocol，and constructed mesh network to achieve network-based intelligent voice alarm system. Because of the sensor temperature and the actual environment temperature, this system design used software compensation after calibrating sensor. In order to reduce system cost, semi-functional node devices were used as front-end node, however, full-function devices were used as routers and coordinator，constructed alarm system within the family by building mesh network，connected to the external public telephone network through the common telephone interface, started the voice alarm module. The results indicate that nodes transmit about 35m in the distance in case of walls and other obstacles by 2.4GHz frequency transmission, this is able to meet family needs and work steadily, but still needs further improvement in power consumption.
上传时间： 2013-10-30
上传用户：swaylong
针对UHF读写器设计中，在符合EPC Gen2标准的情况下，对标签返回的高速数据进行正确解码以达到正确读取标签的要求，提出了一种新的在ARM平台下采用边沿捕获统计定时器数判断数据的方法，并对FM0编码进行解码。与传统的使用定时器定时采样高低电平的FM0解码方法相比，该解码方法可以减少定时器定时误差累积的影响；可以将捕获定时器数中断与数据判断解码相对分隔开，使得中断对解码影响很小，实现捕获与解码的同步。通过实验表明，这种方法提高了解码的效率，在160 Kb/s的接收速度下，读取一张标签的时间约为30次/s。 Abstract: Aiming at the requirement of receiving correctly decoded data from the tag under high-speed communication which complied with EPC Gen2 standard in the design of UHF interrogator， the article introduced a new technology for FM0 decoding which counted the timer counter to judge data by using the edge interval of signal capture based on the ARM7 platform. Compared with the traditional FM0 decoding method which used the timer timed to sample the high and low level， the method could reduce the accumulation of timing error and could relatively separate capture timer interrupt and the data judgment for decoding， so that the disruption effect on the decoding was small and realizd synchronization of capture and decoding. Testing result shows that the method improves the efficiency of decoding， at 160 Kb/s receiving speed， the time of the interrogator to read a tag is about 30 times/s.
上传时间： 2013-11-10
上传用户：liufei
面向Eclips的Nios II软件构建工具手册 The Nios® II Software Build Tools (SBT) for Eclipse™ is a set of plugins based on the Eclipse™ framework and the Eclipse C/C++ development toolkit (CDT) plugins. The Nios II SBT for Eclipse provides a consistent development platform that works for all Nios II embedded processor systems. You can accomplish all Nios II software development tasks within Eclipse, including creating, editing, building, running, debugging, and profiling programs.
上传时间： 2013-11-02
上传用户：瓦力瓦力hong
一些应用利用 Xilinx FPGA 在每次启动时可改变配置的能力，根据所需来改变 FPGA 的功能。Xilinx Platform Flash XCFxxP PROM 的设计修订 (Design Revisioning) 功能，允许用户在单个PROM 中将多种配置存储为不同的修订版本，从而简化了 FPGA 配置更改。在 FPGA 内部加入少量的逻辑，用户就能在 PROM 中存储的多达四个不同的修订版本之间进行动态切换。多重启动或从多个设计修订进行动态重新配置的能力，与 Spartan™-3E FPGA 和第三方并行 flashPROM 一起使用时所提供的 MultiBoot 选项相似。本应用指南将进一步说明 Platform Flash PROM 如何提供附加选项来增强配置失败时的安全性，以及如何减少引脚数量和板面积。此外，Platform Flash PROM 还为用户提供其他优势：iMPACT 编程支持、单一供应商解决方案、低成本板设计和更快速的配置加载。本应用指南还详细地介绍了一个包含 VHDL 源代码的参考设计。
上传时间： 2013-10-10
上传用户：wangcehnglin
WP369可扩展式处理平台-各种嵌入式系统的理想解决方案 ：Delivering unrivaled levels of system performance,flexibility, scalability, and integration to developers,Xilinx's architecture for a new Extensible Processing Platform is optimized for system power, cost, and size. Based on ARM's dual-core Cortex™-A9 MPCore processors and Xilinx’s 28 nm programmable logic,the Extensible Processing Platform takes a processor-centric approach by defining a comprehensive processor system implemented with standard design methods. This approach provides Software Developers a familiar programming environment within an optimized, full featured,powerful, yet low-cost, low-power processing platform.
上传时间： 2013-10-18
上传用户：cursor
本应用指南讲述一种实用的 MicroBlaze™ 系统，用于在非易失性 Platform Flash PROM 中存储软件代码、用户数据和配置数据，以简化系统设计和降低成本。另外，本应用指南还介绍一种可移植的硬件设计、一个软件设计以及在实现流程中使用的其他脚本实用工具。 简介许多 FPGA 设计都集成了使用 MicroBlaze 和 PowerPC™ 处理器的软件嵌入式系统，这些设计同时使用外部易失性存储器来执行软件代码。使用易失性存储器的系统还必须包含一个非易失性器件，用来在断电期间存储软件代码。大多数 FPGA 系统都在电路板上使用 Platform FlashPROM (在本文中称作 PROM)，用于在上电时加载 FPGA 配置数据。另外，许多应用还可能使用其他非易失性器件(如 SPI Flash、Parallel Flash 或 PIC)来保存 MAC 地址等少量用户数据，因此导致系统电路板上存在大量非易失性器件。
标签： MicroBlaze Platform Flash XAPP
上传时间： 2013-10-15
上传用户：rocwangdp
The Xilinx Zynq-7000 Extensible Processing Platform (EPP) redefines the possibilities for embedded systems, giving system and software architects and developers a flexible platform to launch their new solutions and traditional ASIC and ASSP users an alternative that aligns with today’s programmable imperative. The new class of product elegantly combines an industrystandard ARMprocessor-based system with Xilinx 28nm programmable logic—in a single device. The processor boots first, prior to configuration of the programmable logic. This, along with a streamlined workflow, saves time and effort and lets software developers and hardware designers start development simultaneously.
上传时间： 2013-10-09
上传用户：evil
