特点 最高輸入頻率 10KHz 显示范围0-9999（一段设定）0至999999累积量 计数速度 50/10000脈波/秒可选择 输入脈波具有预设刻度功能 累积量同步（批量）或非同步（批次）计数可选择 数位化指拨设定操作简易 计数暂时停止功能 1组报警功能 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脉波触发电位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高输入频率: <10KHz (up,down,up/down mode) 输出动作时间 : 0.1 to 99.9 second adjustable 输出复归方式: Manual(N) or automatic (R or C) can be modif 继电器容量: AC 250V-5A, DC 30V-7A 显示值范围: 0-9999（PV,SV） 0-999999(TV) 显示幕: Red high efficiency LEDs high 7.0mm (.276")(PV,SV) Red high efficiency LEDs high 9.2mm (.36")(TV) 参数设定方式: Touch switches 感应器电源: 12VDC +/-3%(<60mA) 记忆方式: Non-volatile E2PROM memory 绝缘耐压能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用环境条件: 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2013-10-24
上传用户：wvbxj
特点 显示值范围-199999至999999位數 最高輸入頻率 5KHz 90度相位差加減算具有提高解析度4倍功能 输入脈波具有预设刻度功能 定位基准值可任意設定 比較磁滯值可任意設定 数位化指拨设定操作简易 3组继电器输出功能 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脉波触发电位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高输入频率: <5KHz 定位置范围: -199999 to 999999 second adjustabl 比较磁滞范围: 0 to 9999 adjustable 继电器容量: AC 250V-5A, DC 30V-7A 显示值范围: -199999 to 999999 显示幕: Red high efficiency LEDs high 9.2mm (.36") 参数设定方式: Touch switches 感应器电源: 12VDC +/-3%(<60mA) 记忆方式: Non-volatile E2PROM memory 绝缘耐压能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用环境条件: 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2014-12-03
上传用户：xjz632
特点 最高輸入頻率 10KHz 计数速度 50/10000脈波/秒可选择 四种输入模式可选择(加算,減算,加減算,90度相位差加減算) 90度相位差加減算具有提高解析度4倍功能 输入脈波具有预设刻度功能 计数暂时停止功能 3组报警功能 15BIT类比输出功能 数位RS-485界面 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脉波触发电位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高输入频率: <10KHz (up,down,up/down mode) <3KHz (quadrature mode) 输出动作时间 : 0.1 to 99.9 second adjustable 输出复归方式: Manual(N) or automatic (R or C) can be modif 继电器容量: AC 250V-5A, DC 30V-7A 显示值范围: -199999 to 999999 类比输出解析度: 15 bit DAC 输出反应速度: < 1/f+10ms(0-90%) 输出负载能力: < 10mA for voltage mode < 10V for current mode <[(V+)-7.5V]/20mA for two-wire mode 输出之涟波: < 0.1% F.S. 通讯位址: "01"-"FF" 传输速度: 19200/9600/4800/2400 selective 通信协议: Modbus RTU mode 显示幕: Red high efficiency LEDs high 14.22mm (.56") 参数设定方式: Touch switches 感应器电源: 12VDC +/-3%(<60mA) 记忆方式: Non-volatile E2PROM memory 绝缘耐压能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用环境条件: 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2013-11-23
上传用户：redmoons
特点 最高輸入頻率 10KHz 计数速度 50/10000脈波/秒可选择 四种输入模式可选择(加算,減算,加減算,90度相位差加減算) 90度相位差加減算具有提高解析度4倍功能 输入脈波具有预设刻度功能 前置量设定功能(二段設定)可选择 数位化指拨设定操作简易 计数暂时停止功能 3组报警功能 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脉波触发电位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高输入频率: <10KHz (up,down,up/down mode) <5KHz (quadrature mode) 输出动作时间 : 0.1 to 99.9 second adjustable 输出复归方式: Manual(N) or automatic (R or C) can be modif 继电器容量: AC 250V-5A, DC 30V-7A 显示值范围: -199999 to 999999 显示幕: Red high efficiency LEDs high 9.2mm (.36") 参数设定方式: Touch switches 感应器电源: 12VDC +/-3%(<60mA) ( 感應器電源 ) 记忆方式: Non-volatile E2PROM memory 绝缘耐压能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用环境条件: 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2013-11-12
上传用户：909000580
The LPC2292/2294 microcontrollers are based on a 16/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, together with 256 kB of embedded high-speed flash memory. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at the maximum clock rate. For critical code size applications, the alternative 16-bit Thumb mode reduces code by more than 30 pct with minimal performance penalty. With their 144-pin package, low power consumption, various 32-bit timers, 8-channel 10-bit ADC, 2/4 (LPC2294) advanced CAN channels, PWM channels and up to nine external interrupt pins these microcontrollers are particularly suitable for automotive and industrial control applications as well as medical systems and fault-tolerant maintenance buses. The number of available fast GPIOs ranges from 76 (with external memory) through 112 (single-chip). With a wide range of additional serial communications interfaces, they are also suited for communication gateways and protocol converters as well as many other general-purpose applications. Remark: Throughout the data sheet, the term LPC2292/2294 will apply to devices with and without the /00 or /01 suffix. The suffixes /00 and /01 will be used to differentiate from other devices only when necessary.
上传时间： 2014-12-30
上传用户：aysyzxzm
Abstract: With industrial/scientific/medical (ISM) band radio frequency (RF) products, often times users are new to the structure of Maxim's low pin-count transmitters andfully integrated superheterodyne receivers. This tutorial provides simple steps that can be taken to get the best performance out of these transmitters and receivers whileproviding techniques to measure the overall capability of the design.
上传时间： 2013-11-02
上传用户：yph853211
The LTC®3207/LTC3207-1 is a 600mA LED/Camera driverwhich illuminates 12 Universal LEDs (ULEDs) and onecamera fl ash LED. The ULEDs are considered universalbecause they may be individually turned on or off, setin general purpose output (GPO) mode, set to blink at aselected on-time and period, or gradate on and off at aselected gradation rate. This device also has an externalenable (ENU) pin that may be used to blink, gradate, orturn on/off the LEDs without using the I2C bus. This may beuseful if the microprocessor is in sleep or standby mode. Ifused properly, these features may save valuable memoryspace, programming time, and reduce the I2C traffi c.
上传时间： 2014-01-04
上传用户：LANCE
本软件是关于MAX338, MAX339的英文数据手册：MAX338, MAX339 8通道/双4通道、低泄漏、CMOS模拟多路复用器 The MAX338/MAX339 are monolithic, CMOS analog multiplexers (muxes). The 8-channel MAX338 is designed to connect one of eight inputs to a common output by control of a 3-bit binary address. The dual, 4-channel MAX339 is designed to connect one of four inputs to a common output by control of a 2-bit binary address. Both devices can be used as either a mux or a demux. On-resistance is 400Ω max, and the devices conduct current equally well in both directions. These muxes feature extremely low off leakages (less than 20pA at +25°C), and extremely low on-channel leakages (less than 50pA at +25°C). The new design offers guaranteed low charge injection (1.5pC typ) and electrostatic discharge (ESD) protection greater than 2000V, per method 3015.7. These improved muxes are pin-compatible upgrades for the industry-standard DG508A and DG509A. For similar Maxim devices with lower leakage and charge injection but higher on-resistance, see the MAX328 and MAX329.
上传时间： 2013-11-12
上传用户：18711024007
This example provides a description of how to use the USART with hardware flowcontrol and communicate with the Hyperterminal.First, the USART2 sends the TxBuffer to the hyperterminal and still waiting fora string from the hyperterminal that you must enter which must end by '\r'character (keypad ENTER button). Each byte received is retransmitted to theHyperterminal. The string that you have entered is stored in the RxBuffer array. The receivebuffer have a RxBufferSize bytes as maximum. The USART2 is configured as follow: - BaudRate = 115200 baud - Word Length = 8 Bits - One Stop Bit - No parity - Hardware flow control enabled (RTS and CTS signals) - Receive and transmit enabled - USART Clock disabled - USART CPOL: Clock is active low - USART CPHA: Data is captured on the second edge - USART LastBit: The clock pulse of the last data bit is not output to the SCLK pin
上传时间： 2013-10-31
上传用户：yy_cn
This example shows how to update at regulate period the WWDG counter using theEarly Wakeup interrupt (EWI). The WWDG timeout is set to 262ms, refresh window set to 41h and the EWI isenabled. When the WWDG counter reaches 40h the EWI is generated and in the WWDGISR the counter is refreshed to prevent a WWDG reset and led connected to PC.07is toggled.The EXTI line9 is connected to PB.09 pin and configured to generate an interrupton falling edge.In the NVIC, EXTI line9 to 5 interrupt vector is enabled with priority equal to 0and the WWDG interrupt vector is enabled with priority equal to 1 (EXTI IT > WWDG IT). The EXTI Line9 will be used to simulate a software failure: once the EXTI line9event occurs (by pressing Key push-button on EVAL board) the correspondent interruptis served, in the ISR the led connected to PC.07 is turned off and the EXTI line9pending bit is not cleared. So the CPU will execute indefinitely EXTI line9 ISR andthe WWDG ISR will never be entered(WWDG counter not updated). As result, when theWWDG counter falls to 3Fh the WWDG reset occurs.If the EXTI line9 event don抰 occurs the WWDG counter is indefinitely refreshed inthe WWDG ISR which prevent from WWDG reset. If the WWDG reset is generated, after resuming from reset a led connected to PC.06is turned on. In this example the system is clocked by the HSE(8MHz).
上传时间： 2013-11-11
上传用户：gundamwzc
