叙述了基于过采样技术,使用软件方法提高单片机片内A/ D 分辨率的基本原理及实现方法。给出了一个实现示例,将C8051F040 片内12 位分辨率ADC 提高到16 位分辨率。
上传时间: 2014-01-08
上传用户:a3318966
USB2I2C是一个USB总线的转I2C总线的专用接口芯片。通过USB2I2C芯片用户可以非常方便地实现PC机USB总线和下位机端各种I2C/IIC设备(如,ATMEL公司的AT24CXX系列EEPROM;I2C总线8位并行IO口扩展芯片PCF8574/JLC1562;I2C接口实时时钟芯片DS1307/PCF8563/SD2000D/M41T80/ME901/ISL1208/;I2C数据采集ADC芯片MCP3221(12bitADC)/ADS1100(16bitADC)/ADS1112(16bitADC)/MAX1238(12bitADC)/MAX1239(12bitADC);I2C接口数模转换DAC芯片DAC5574(8bitDAC)/DAC6573(10bitDAC)/DAC8571 (16bitDAC)/;I2C接口温度传感器TMP101/TMP275/DS1621/MAX6625,等)之间的通信。 USB2I2C芯片上位机PC端提供简单易用的USBIOX.DLL动态库调用,可以方便地被VB,VC,Delphi等上位机开发工具调用
上传时间: 2014-12-26
上传用户:Amygdala
adc
上传时间: 2014-12-26
上传用户:yare
利用单片机具有的智能程序控制的特点,设计了基于STC89C52单片机的"二极管特性测试器",可对二极管一般特性进行快速测试。通过稳定线性电流源给二极管加载恒定电流,然后由高精度模数转换器测试其压降,以此为基础可判断二极管好坏、检测二极管极性和测试二极管伏安特性等,避免了用万用表测试只能测得极性而不知其特性这一缺点。可用于电子设计制作过程中对二极管进行快速测试,以确定被测二极管是否满足电路的设计要求。 Abstract: By making good use of the intelligent control function of the Micro Controller Unit (MCU), the diode trait tester was designed based on the STC89C52,which could be used to test the trait of a diode rapidly. By loading constant current to diode through the stable linear current source, and measuring the voltage drop of the diode by high-precision analogue-to-digital converter (ADC), it can judge whether the diode is good or not, distinguish the polarity of the diode, and test the trait that the diode, which can avoid the fault of using a multimeter can only measure the polarity but not the trait. This device can be used to test the trait of a diode quickly,and to make sure that whether a diode can be used in the electronic design or not.
上传时间: 2013-11-13
上传用户:assef
常用PIC系列产品特性一览表 器件 存储器 类型 字数 EEPROM 数据 存储器 RAM I/O 引脚数 ADC (-Bit) 比较 器 运 放 定时器/WDT 串行接口 最高 速度 MHz 封装 PDIP /SOIC ICSP CCP / ECCP 输出电流 (per I/O) 振荡器 频率 (MHz) 参考 电压 VREF LCD PWM 堆栈 深度 High Voltage Wakeup On Change PIC16C432 OTP 2048x14 128 12 2 1-8bit/1-WDT 20 20 √ 25 mA 4 0 0 PIC16C433 OTP 2048x14 128 6 4/8 1-8bit/1-WDT 10 18 √ 25 mA 0 0 PIC16C505 OTP 1024x12 72 12 1-8bit/1-WDT 20 14 √ 25 mA 4 0 0 PIC16C54 OTP 512x12 25 12 1-8bit/1-WDT 20 18/20 20 mA 0 0 PIC16C54A OTP 512x12 25 12 1-8bit/1-WDT 20 18/20 20 mA 0 0 PIC16C54C OTP 512x12 25 12 1-8bit/1-WDT 40 18/20 20 mA 0 0 PIC16C55 OTP 512x12 24 20 1-8bit/1-WDT 20 28 20 mA 0 0 PIC16C554 OTP 512x14 80 13 1-8bit/1-WDT 20 18/20 √ 25 mA 0 0 PIC16C558 OTP 2048x14 128 13 1-8bit/1-WDT 20 18/20 √ 25 mA 0 0 PIC16C55A OTP 512x12 24 20 1-8bit/1-WDT 40 28 20 mA 0 0 PIC16C56 OTP 1024x12 25 12 1-8bit/1-WDT 20 18/20 20 mA 0 0 PIC16C56A OTP 1024x12 25 12 1-8bit/1-WDT 40 18/20 20 mA 0 0 PIC16C57 OTP 2048x12 72 20 1-8bit/1-WDT 20 28 20 mA 0 0 PIC16C57C OTP 2048x12 72 20 1-8bit/1-WDT 40 28 20 mA 0 0 PIC16C58B OTP 2048x12 73 12 1-8bit/1-WDT 40 18/20 20 mA 0 0 PIC16C620 OTP 512x14 80 13 2 1-8bit/1-WDT 20 18/20 √ 25 mA √ 0 0 PIC16C620A OTP 512x14 96 13 2 1-8bit/1-WDT 40 18/20 √ 25 mA √ 0 0 PIC16C621 OTP 1024x14 80 13 2 1-8bit/1-WDT 20 18/20 √ 25 mA √ 0 0 PIC16C621A OTP 1024x14 96 13 2 1-8bit/1-WDT 40 18/20 √ 25 mA √ 0 0 PIC16C622 OTP 2048x14 128 13 2 1-8bit/1-WDT 20 18/20 √ 25 mA √ 0 0 PIC16C622A OTP 2048x14 128 13 2 1-8bit/1-WDT 40 18/20/40 √ 25 mA √ 0 0 PIC16C62A OTP 2048x14 128 22 2-8bit/1-16bit/1-WDT I²C/ SPI 20 28/ √ 1 25 mA 1 0 0 PIC16C62B OTP 2048x14 128 22 2-8bit/1-16bit/1-WDT I²C /SPI 20 28 √ 1 25 mA 1 0 0 PIC16C63 OTP 4096x14 192 22 2-8bit/1-16bit/1-WDT USART/I²C /SPI 20 28 √ 2 25 mA 2 0 0 PIC16C63A OTP 4096x14 192 22 2-8bit/1-16bit/1-WDT USART/I²C/SPI 20 28 √ 2 25 mA 2 0 0 PIC16C642 OTP 4096x14 176 22 2 1-8bit/1-WDT 20 28 √ 25 mA √ 0 0 PIC16C64A OTP 2048x14 128 33 2-8bit/1-16bit/1-WDT I²C /SPI 20 40/44 √ 1 25 mA 1 0 0 PIC16C65A OTP 4096x14 192 33 2-8bit/1-16bit/1-WDT USART/I²C/SPI 20 40/44 √ 2 25 mA 2 0 0 PIC16C65B OTP 4096x14 192 33 2-8bit/1-16bit/1-WDT USART/I²C/SPI 20 40/44 √ 2 25 mA 2 0 0 PIC16C66 OTP 8192x14 368 22 2-8bit/1-16bit/1-WDT USART/I²C/SPI 20 28 √ 2 25 mA 2 0 0 PIC16C662 OTP 4096x14 176 33 2 1-8bit/1-WDT 20 40/44 √ 25 mA √ 0 0 PIC16C67 OTP 8192x14 368 33 2-8bit/1-16bit/1-WDT USART/I²C /SPI 20 40/44 √ 2 25 mA 2 0 0 PIC16C71 OTP 1024x14 36 13 4/8 1-8bit/1-WDT 20 18 √ 25 mA 0 0 PIC16C710 OTP 512x14 36 13 4/8 1-8bit/1-WDT 20 18/20 √ 25 mA 0 0 PIC16C711 OTP 1024x14 68 13 4/8 1-8bit/1-WDT 20 18/20 √ 25 mA
上传时间: 2013-10-12
上传用户:xjy441694216
以C8051F020为核心处理器,设计无线传感器网络数据采集系统。系统采用SZ05-ADV型无线通讯模块组建Zigbee无线网络,结合嵌入式系统的软硬件技术,完成终端节点的8路传感器信号的数据采集。现场8路信号通过前端处理后,分别送入C8051F020的12位A/D转换器进行转换。经过精确处理、存储后的现场数据,通过Zigbee无线网络传送到上位机,系统可达到汽车试验中无线测试的目的。 Abstract: This paper designs a wireless sensor network system for data acquisition with C8051F020 as core processors.The system used SZ05-ADV wireless communication module,set up a Zigbee wireless network, combined with hardware and software technologies of embedded systems,completed the end-node 8-locale sensor signal data acquisition.Eight locale signals were sent separately into the 12-bit ADC of C8051F020 for conversion through front treatment.After accurate processing and storage,the locale data was transmitted to the host computer through Zigbee wireless.The system achieves the purpose of wireless testing in vehicle trial.
标签: C8051F020 Zigbee 汽车测试 系统设计
上传时间: 2013-11-23
上传用户:dsgkjgkjg
主要特点管脚完全与三星9454兼容8位CISC型内核(MC05)4K byte OTP ROM208 byte RAM3组IO口(最多可支持17个通用IO口和1个输入口)1个PWM输出1个8位基本定时器1个8位带比较输出的定时器1个10位ADC(9路输入)2个外中断、1个定时器中断、1个PWM中断看门狗复位功能3V低压复位可选晶振/RC振荡晶振400K-8MHzRC振荡有3.2MHz(@5V,typ.)、8MHz(@5V,typ.)、外接电阻电容3种可选
上传时间: 2013-11-05
上传用户:Jerry_Chow
概述 BL22P64可以作为许多中高档小家电(如电磁炉、微波炉、豆浆机等)的控制芯片,这一类小家电通常都需要灵活的、可编程的控制方式,并需要AD、PWM等资源,同时满足抗电磁干扰(EMC)4KV的要求。 主要特点 ●8位CISC型内核(兼容MotorolaHC05)●4KbyteOTPROM●208byteRAM●3组IO口(最多18个IOPIN)●1个PWM输出●1个8位基本定时器●1个8位带MATCH输出的定时器●1个10位ADC(9路输入)●2个外中断、1个定时器中断、1个PWM中断●WATCHDOG●3V低压复位●可选晶振/RC振荡晶振400K-4MHzRC振荡有3.2MHz(@5V,typ.)、0.5MHz(@5V,typ.)、外接电阻3种可选●工作电压2.7-5.5V●工作温度-40-85℃●封装形式:SOP20/DIP20/SOP16
上传时间: 2013-11-06
上传用户:DE2542
利用Atmel公司的ATmega168微处理器,采用A/D转换方式来实现按摩椅控制器的键盘接口,通过在硬件电路中巧妙地选择电阻,在软件设计中采用数字滤波、二分法和区间鉴定等方法,灵敏可靠地实现了按摩椅中30个按键的处理。给出了硬件电路设计和软件设计思想以及部分汇编代码。 Abstract: This paper chooses A/D conversion method to realize the keyboard interface of the controller by using ATmega168 microchip from Atmel Company.It accomplishes 30-key dealing sensitively and reliably in massage chair through skillfully selecting resistors in hardware circuit and using digital filter,dichotomy and area-judging method in software design.The hardware design circuit, software design idea and partly assembles code are presented mainly.
上传时间: 2014-01-10
上传用户:咔乐坞
清单1 LSDAA: ADC R16,R16 ;十进制数(在R16中)左移调整子程序 ADDAA: IN R6,SREG ;bcd码相加调整子程序,先保存相加后的 LDI R17,$66 ;状态the old status ADD R16,R17 ;再将和预加立即数$66 IN R17,SREG ;输入相加后新状态(the new status) OR R6,R17 ;新旧状态相或 SBRS R6,0 ;相或后进位置位则跳行 SUBI R16,$60 ;否则减去$60(十位bcd不满足调整条件) SBRS R6,5 ;半进位置位则跳行 SUBI R16,6 ;否则减去$06(个位bcd不满足调整条件) ROR R6 ;向高位BCD返还进位位! RET
上传时间: 2013-10-08
上传用户:zh_901