Size, output flexibility and efficiency advantages havemade switching regulators common in electronic apparatus.The continued emphasis on these attributes hasresulted in circuitry with 95% efficiency that requiresminimal board area. Although these advantages are welcome,they necessitate compromising other parameters
上传时间： 2013-11-04
上传用户：zycidjl
The latest generation of Texas Instruments (TI) boardmountedpower modules utilizes a pin interconnect technologythat improves surface-mount manufacturability.These modules are produced as a double-sided surfacemount(DSSMT) subassembly, yielding a case-less constructionwith subcomponents located on both sides of theprinted circuit board (PCB). Products produced in theDSSMT outline use the latest high-efficiency topologiesand magnetic-component packaging. This providescustomers with a high-efficiency, ready-to-use switchingpower module in a compact, space-saving package. Bothnonisolated point-of-load (POL) switching regulators andthe isolated dc/dc converter modules are being producedin the DSSMT outline.TI’s plug-in power product line offers power modules inboth through-hole and surface-mount packages. The surfacemountmodules produced in the DSSMT outline use asolid copper interconnect with an integral solder ball fortheir
上传时间： 2013-10-10
上传用户：1184599859
EDID-BOARD资料
标签： EDID-BOARD
上传时间： 2013-11-21
上传用户：tou15837271233
The P89LPC912/913/914 are single-chip microcontrollers in low-cost 14-pin packages, based on a high performance processor architecture that executes instructions in two to four clocks, six times the rate of standard 80C51 devices. Many system level functions have been incorporated into the P89LPC912/913/914 in order to reduce component count, board space, and system cost.
上传时间： 2013-10-12
上传用户：司令部正军级
介绍基于ISA总线与KH-9300的数据采集板卡的设置，详细说明8254定时计数器及8259中断控制器的结构特点、工作方式、控制字等，探讨中断类型、中断处理程序、中断矢量表及其填写。重点讲述使用TorboC编写中断服务程序的方法，应注意的主要问题及程序测试的结果。 Abstract: The settings of KH-9300 data acquisition board based on the ISA bus is introduced,the structural characteristics,working methods,control characters of the timing counter 8254 and interruptioncontroller 8259 are explained in detail.The interruption type,interrupt handling programs,interruption vector table and its filling also are discussed.Further,great emphasis is put on the method of interrupt service program compiled by Torbo C,the main issues that should be noted,and the results of program testing.
上传时间： 2013-11-14
上传用户：qq527891923
介绍了基于单片机航空交流电参数测试仪的系统设计。以Silicon Labs公司的C8051F005单片机为核心设计出数据采集板，通过RS-232串口与上位机通讯。运用Lab Windows/CVI编写的上位机软件实现信号的检测以及波形和数据的显示，给出了测试仪硬件电路的组成和软件流程图。本系统具有硬件结构简单、容易实现和成本低等特点，在实际应用中其稳定性、精确性均能满足客户要求。 Abstract: The design of aeronautics AC parameters tester based on the single-chip is introduced.The core component of data acquisition board is C8051F005 single chip of Silicon Labs Company,and communication with PC through RS-232. The signal processing software programmed with LabWindows/CVI can be used successfully to fulfill inspection of signal and display of the waveform and data. The hardware and software configuration of test instrument are provided.The hardware of the system is simple, and can be easily realized.The stability and precision of the measurement instrument are enough to meet the requirements.
上传时间： 2013-11-18
上传用户：wang5829
The MSP-FET430PIF is a Parallel Port interface (does not include target board) that is used to program and debug MSP430 FET tools and test boards through the JTAG interface. This interface is included in our FET tools, but sold without the development board. This interface uses a Parallel PC Port to communicate to the Debugger Software (IAR Kickstart software included) running on the PC. The interface uses the standard 14 pin header to communicate to the MSP430 device using the standard JTAG protocol. The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is extremely low power, no external power supply is required. The tool has an integrated software environment and connects directly to the PC which greatly simplifies the set-up and use of the tool. The flash development tool supports development with all MSP430 flash parts. Features MSP430 debugging interface to connect a MSP430-Flash-device to a Parallel port on a PC Supports JTAG debug protocol (NO support for Spy-Bi-Wire (2-wire JTAG) debug protocol, Spy-Bi-Wire (2-wire JTAG) is supported by MSP-FET430UIF) Parallel Port cable and a 14-conductor target cable Full documentation on CD ROM Integrated IAR Kickstart user interface which includes: Assembler Linker Limulator Source-level debugger Limited C-compiler Technical specifications: Backwardly compatable with existing FET tool boards.
上传时间： 2013-10-26
上传用户：fengweihao158@163.com
用户程序示例教程 The Blinky project is a simple program for the LPC2138using Keil MCB2130 Microcontroller Board. It blinks the LEDs at speed according to the Potentiometer setting and prints the current seting to the Serial Port 1.In addition it generates a sine wave with an adjustable frequency on the speaker of the board.
上传时间： 2014-12-27
上传用户：hongmo
<Almost since the introduction of microcontrollers as electronic components there always has been an oscillatorcircuit on the device to make it work. From application point of view only some external components wererequired to make it work. However, to make sure that it will always work required more effort. This report is basedon feedback from the market from customers applying 8-bit mircrocontrollers.>
标签： oscillators X-tal bit mic
上传时间： 2013-11-12
上传用户：穿着衣服的大卫
The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using SW routines implemented in C. The code is focused onthe SAB C513, but will fit to all C500 derivatives.Beyond the low level software drivers a test shell is delivered. This shell allows a quicktest of the software drivers by an emulator or a starter kit demo board.
上传时间： 2013-11-24
上传用户：363186
