This application note features 8-, 10-, and 12-bit dataacquisition components in various circuit configurations.The circuits include battery monitoring, temperature sensing,isolated serial interfaces, and microprocessor andmicrocontroller serial and parallel interfaces. Also includedare voltage reference circuits (Application note 42contains more voltage reference circuits).
上传时间： 2014-01-15
上传用户：zq70996813
This application note is an overview discussion of theLinear Technology SPICE macromodel library. It assumeslittle if any prior knowledge of this software library or itshistory. However, it does assume familiarity with both theanalog simulation program SPICE (or one of its manyderivatives), and modern day op amps, including bipolar,JFET, and MOSFET amplifier technologies
上传时间： 2013-11-14
上传用户：zhanditian
This publication represents the largest LTC commitmentto an application note to date. No other application noteabsorbed as much effort, took so long or cost so much.This level of activity is justified by our belief that high speedmonolithic amplifiers greatly interest users.
标签： 高速放大器
上传时间： 2014-01-07
上传用户：wfl_yy
This note describes some of the unique IC design techniques incorporated into a fast, monolithic power buffer, the LT1010. Also, some application ideas are described such as capacitive load driving, boosting fast op amp output current and power supply circuits.
上传时间： 2013-11-12
上传用户：671145514
A complete design for a data acquisition card for the IBM PC is detailed in this application note. Additionally, C language code is provided to allow sampling of data at speed of more than 20kHz. The speed limitation is strictly based on the execution speed of the "C" data acquisition loop. A "Turbo" XT can acquire data at speeds greater than 20kHz. Machines with 80286 and 80386 processors can go faster than 20kHz. The computer that was used as a test bed in this application was an XT running at 4.77MHz and therefore all system timing and acquisition time measurements are based on a 4.77MHz clock speed.
上传时间： 2013-10-29
上传用户：BOBOniu
A tutorial on SAR type A/D converters, this note contains detailed information on several 12-bit circuits. Comparator, clocking, and preamplifier designs are discussed. A final circuit gives a 12-bit conversion in 1.8µs. Appended sections explain the basic SAR technique and explore D/A considerations.
上传时间： 2014-01-21
上传用户：钓鳌牧马
This application note describes a Linear Technology "Half-Flash" A/D converter, the LTC1099, being connected to a 256 element line scan photodiode array. This technology adapts itself to handheld (i.e., low power) bar code readers, as well as high resolution automated machine inspection applications..
上传时间： 2013-11-21
上传用户：lchjng
ANALOG INPUT BANDWIDTH is a measure of the frequencyat which the reconstructed output fundamental drops3 dB below its low frequency value for a full scale input. Thetest is performed with fIN equal to 100 kHz plus integer multiplesof fCLK. The input frequency at which the output is −3dB relative to the low frequency input signal is the full powerbandwidth.APERTURE JITTER is the variation in aperture delay fromsample to sample. Aperture jitter shows up as input noise.APERTURE DELAY See Sampling Delay.BOTTOM OFFSET is the difference between the input voltagethat just causes the output code to transition to the firstcode and the negative reference voltage. Bottom Offset isdefined as EOB = VZT–VRB, where VZT is the first code transitioninput voltage and VRB is the lower reference voltage.note that this is different from the normal Zero Scale Error.CONVERSION LATENCY See PIPELINE DELAY.CONVERSION TIME is the time required for a completemeasurement by an analog-to-digital converter. Since theConversion Time does not include acquisition time, multiplexerset up time, or other elements of a complete conversioncycle, the conversion time may be less than theThroughput Time.DC COMMON-MODE ERROR is a specification which appliesto ADCs with differential inputs. It is the change in theoutput code that occurs when the analog voltages on the twoinputs are changed by an equal amount. It is usually expressed in LSBs.
上传时间： 2013-11-12
上传用户：pans0ul
Abstract: This application note explains how to layout the MAX20021/MAX20022 automotive quad powermanagementICs (PMICs) to maximize performance and minimize emissions. Example images of a fourlayerlayout are provided.
上传时间： 2013-11-19
上传用户：18711024007
Hyperlynx仿真应用:阻抗匹配.下面以一个电路设计为例，简单介绍一下PCB仿真软件在设计中的使用。下面是一个DSP硬件电路部分元件位置关系(原理图和PCB使用PROTEL99SE设计)，其中DRAM作为DSP的扩展Memory(64位宽度，低8bit还经过3245接到FLASH和其它芯片)，DRAM时钟频率133M。因为频率较高，设计过程中我们需要考虑DRAM的数据、地址和控制线是否需加串阻。下面，我们以数据线D0仿真为例看是否需要加串阻。模型建立首先需要在元件公司网站下载各器件IBIS模型。然后打开Hyperlynx,新建LineSim File(线路仿真—主要用于PCB前仿真验证)新建好的线路仿真文件里可以看到一些虚线勾出的传输线、芯片脚、始端串阻和上下拉终端匹配电阻等。下面，我们开始导入主芯片DSP的数据线D0脚模型。左键点芯片管脚处的标志，出现未知管脚，然后再按下图的红线所示线路选取芯片IBIS模型中的对应管脚。 3http://bbs.elecfans.com/ 电子技术论坛 http://www.elecfans.com 电子发烧友点OK后退到“ASSIGN Models”界面。选管脚为“Output”类型。这样，一样管脚的配置就完成了。同样将DRAM的数据线对应管脚和3245的对应管脚IBIS模型加上(DSP输出，3245高阻，DRAM输入)。下面我们开始建立传输线模型。左键点DSP芯片脚相连的传输线，增添传输线，然后右键编辑属性。因为我们使用四层板，在表层走线，所以要选用“Microstrip”，然后点“Value”进行属性编辑。这里，我们要编辑一些PCB的属性，布线长度、宽度和层间距等，属性编辑界面如下：再将其它传输线也添加上。这就是没有加阻抗匹配的仿真模型(PCB最远直线间距1.4inch，对线长为1.7inch)。现在模型就建立好了。仿真及分析下面我们就要为各点加示波器探头了，按照下图红线所示路径为各测试点增加探头：为发现更多的信息，我们使用眼图观察。因为时钟是133M，数据单沿采样，数据翻转最高频率为66.7M，对应位宽为7.58ns。所以设置参数如下：之后按照芯片手册制作眼图模板。因为我们最关心的是接收端(DRAM)信号，所以模板也按照DRAM芯片HY57V283220手册的输入需求设计。芯片手册中要求输入高电平VIH高于2.0V，输入低电平VIL低于0.8V。DRAM芯片的一个note里指出，芯片可以承受最高5.6V，最低-2.0V信号(不长于3ns)：按下边红线路径配置眼图模板：低8位数据线没有串阻可以满足设计要求，而其他的56位都是一对一，经过仿真没有串阻也能通过。于是数据线不加串阻可以满足设计要求，但有一点需注意，就是写数据时因为存在回冲，DRAM接收高电平在位中间会回冲到2V。因此会导致电平判决裕量较小，抗干扰能力差一些，如果调试过程中发现写RAM会出错，还需要改版加串阻。
上传时间： 2013-11-05
上传用户：dudu121
