NAME: u2440mon.c DESC: u2440mon entry point,menu,download HISTORY: Mar.25.2002:purnnamu: S3C2400X profile.c is ported for S3C2410X. Mar.27.2002:purnnamu: DMA is enabled. Apr.01.2002:purnnamu: isDownloadReady flag is added. Apr.10.2002:purnnamu: - Selecting menu is available in the waiting loop. So, isDownloadReady flag gets not needed - UART ch.1 can be selected for the console. Aug.20.2002:purnnamu: revision number change 0.2 -> R1.1 Sep.03.2002:purnnamu: To remove the power noise in the USB signal, the unused CLKOUT0,1 is disabled.
标签： 2440 mon download purnnamu
上传时间： 2016-05-12
上传用户：wff
The Radio Interface Layer is the name for an interface that was developed especially for the Pocket PC Phone Edition. It is meant to abstract the interface with a phone/modem device. To achieve this it is closely modelled after the GSM AT command interface. Unfortunately the API was not published officially by Microsoft. Instead more high level API s were published that should be sufficient for developers. Again, unfortunately they are not sufficient. For example the API for receiving notification of incoming SMS messages is arranged for exclusively for one application per type of SMS. Apparently this will be improved upon in Pocket PC 2003. Another area is the availablity of a true AT command modem interface to interact with the GSM modem directly, which is also absent.
标签： especially Interface for developed
上传时间： 2013-12-02
上传用户：wff
The DiskPerf filter driver monitors disk-accesses, capturing performance data. It supports Plug and Play, Power Management, and WMI . It is not 64-bit compliant
标签： disk-accesses performance capturing DiskPerf
上传时间： 2013-12-23
上传用户：agent
Addfilter is a command-line application which adds and removes filter drivers for a given drive or volume. It is intended to demonstrate how to insert a filter driver into the driver stack of a device. The sample illustrates how to do this by using the SetupDi APIs. The sample works on the x86 platform. It has only been tested in a 32-bit environment. Since Addfilter is not a driver, it does not deal with Plug and Play or Power Management.
标签： command-line application Addfilter drivers
上传时间： 2016-05-17
上传用户：xzt
SimpliciTI™ -1.0.3.exe for CC11xx and CC25xx SimpliciTI is a simple low-power RF network protocol aimed at small (<256) RF networks. Such networks typically contain battery operated devices which require long battery life, low data rate and low duty cycle and have a limited number of nodes talking directly to each other or through an access point or range extenders. Access point and range extenders are not required but provide extra functionality such as store and forward messages. With SimpliciTI the MCU resource requirements are minimal which results in the low system cost.
标签： SimpliciTI low-power network simple
上传时间： 2014-11-05
上传用户：rishian
SimpliciTI™ -1.0.4.exe for CC2430 SimpliciTI is a simple low-power RF network protocol aimed at small (<256) RF networks. Such networks typically contain battery operated devices which require long battery life, low data rate and low duty cycle and have a limited number of nodes talking directly to each other or through an access point or range extenders. Access point and range extenders are not required but provide extra functionality such as store and forward messages. With SimpliciTI the MCU resource requirements are minimal which results in the low system cost.
标签： SimpliciTI low-power protocol network
上传时间： 2016-05-21
上传用户：R50974
I made a lot of changed on this object,such as * // 1.Encapsulates all code in one userobjet,since PB does not * // support "Address of Function" , so we can not set new * // WndProc, just makes the object more easy to use. * // 2.Uses structure array instead of Datastore * // 3.Calc width of menuitem at runtime(MEASUREITEM) * // 4.Draw disabled status
标签： Encapsulates userobjet changed object
上传时间： 2014-01-14
上传用户：lx9076
This LDPC software is intended as an introduction to LDPC codes computer based simulation. The pseudo-random irregular low density parity check matrix is based on Radford M. Neal’s programs collection, which can be found in [1]. While Neal’s collection is well documented, in my opinion, C source codes are still overwhelming, especially if you are not knowledgeable in C language. My software is written for MATLAB, which is more readable than C. You may also want to refer to another MATLAB based LDPC source codes in [2], which has different flavor of code-writing style (in fact Arun has error in his log-likelihood decoder).
标签： LDPC introduction simulation software
上传时间： 2014-12-05
上传用户：change0329
MATFOR FFT Visual Fortran program. MATFOR Extensions, as implied in the name, are data or components external to MATFOR modules that can be used to add versatility to MATFOR programs. Currently there are two types of extensions available with MATFOR, they are MATLAB Interface and Tecplot FileIO. MATLAB Interface, a new feature in MATFOR 4.1, provides MATFOR users access to MATLAB functions so they can obtain functionality that has not been built into MATFOR. The ability of using MATLAB functions makes MATFOR an ideal tool for those who create prototypes using MATLAB, then do implementation in C++ and other programming languages. Through the use of MATFOR, users may perform quick results comparisons between MATLAB and other languages.
标签： MATFOR Extensions component Fortran
上传时间： 2013-12-11
上传用户：xieguodong1234
％ DYNMODES calculates ocean dynamic vertical modes ％ taking a column vector of Brunt-Vaisala values (Nsq) at ％ different pressures (p) and calculating some number of ％ dynamic modes (nmodes). ％ note: The input pressures need not be uniformly spaced, ％ and the deepest pressure is assumed to be the bottom.
标签： Brunt-Vaisala calculates DYNMODES vertical
上传时间： 2013-12-06
上传用户：busterman
