DC/DC 升压IC：The FP6291 is a current mode boost DC-DC converter. Its PWM circuitry with built-in 0.25 Ω power MOSFET make this regulator highly power efficient. The internal compensation network also minimizes as much as 6 external component counts. The non-inverting input of error amplifier connects to a 0.6V precision reference voltage and internal soft-start function can reduce the inrush current. The FP6291 is available in the SOT23-6L package and provides space-saving PCB for the application fields.
上传时间： 2013-11-07
上传用户：3294322651
A frequent requirement in systems involves drivinganalog signals into non-linear or reactive loads. Cables,transformers, actuators, motors and sample-hold circuitsare examples where the ability to drive diffi cult loads isrequired. Although several power buffer amplifi ers areavailable, none have been optimized for driving diffi cultloads.
上传时间： 2014-12-24
上传用户：1109003457
This application report discusses the design of non-invasive optical plethysmographyalso called as pulsoximeter using the MSP430FG437 Microcontroller (MCU). Thepulsoximeter consists of a peripheral probe combined with the MCU displaying theoxygen saturation and pulse rate on a LCD glass. The same sensor is used for bothheart-rate detection and pulsoximetering in this application. The probe is placed on aperipheral point of the body such as a finger tip, ear lobe or the nose. The probeincludes two light emitting diodes (LEDs), one in the visible red spectrum (660nm) andthe other in the infrared spectrum (940nm). The percentage of oxygen in the body isworked by measuring the intensity from each frequency of light after it transmitsthrough the body and then calculating the ratio between these two intensities.
标签： Pulsoximeter Single-Chip Des
上传时间： 2013-10-27
上传用户：黑漆漆
The STWD100 watchdog timer circuits are self-contained devices which prevent systemfailures that are caused by certain types of hardware errors (non-responding peripherals,bus contention, etc.) or software errors (bad code jump, code stuck in loop, etc.).The STWD100 watchdog timer has an input, WDI, and an output, WDO (see Figure 2). Theinput is used to clear the internal watchdog timer periodically within the specified timeoutperiod, twd (see Section 3: Watchdog timing). While the system is operating correctly, itperiodically toggles the watchdog input, WDI. If the system fails, the watchdog timer is notreset, a system alert is generated and the watchdog output, WDO, is asserted (seeSection 3: Watchdog timing).The STWD100 circuit also has an enable pin, EN (see Figure 2), which can enable ordisable the watchdog functionality. The EN pin is connected to the internal pull-downresistor. The device is enabled if the EN pin is left floating.
上传时间： 2013-10-22
上传用户：taiyang250072
SRAM-based FPGAs are non-volatile devices. Upon powerup, They are required to be programmed from an external source. This procedure allows anyone to easily monitor the bit-stream, and clone the device. The problem then becomes how can you effectively protect your intellectual property from others in an architecture where the part is externally programmed?
上传时间： 2013-11-06
上传用户：wl9454
特点 最高輸入頻率 10KHz 显示范围0-9999（一段设定）0至999999累积量 计数速度 50/10000脈波/秒可选择 输入脈波具有预设刻度功能 累积量同步（批量）或非同步（批次）计数可选择 数位化指拨设定操作简易 计数暂时停止功能 1组报警功能 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脉波触发电位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高输入频率: <10KHz (up,down,up/down mode) 输出动作时间 : 0.1 to 99.9 second adjustable 输出复归方式: Manual(N) or automatic (R or C) can be modif 继电器容量: AC 250V-5A, DC 30V-7A 显示值范围: 0-9999（PV,SV） 0-999999(TV) 显示幕: Red high efficiency LEDs high 7.0mm (.276")(PV,SV) Red high efficiency LEDs high 9.2mm (.36")(TV) 参数设定方式: Touch switches 感应器电源: 12VDC +/-3%(<60mA) 记忆方式: Non-volatile E2PROM memory 绝缘耐压能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用环境条件: 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2013-10-24
上传用户：wvbxj
特点 显示值范围-199999至999999位數 最高輸入頻率 5KHz 90度相位差加減算具有提高解析度4倍功能 输入脈波具有预设刻度功能 定位基准值可任意設定 比較磁滯值可任意設定 数位化指拨设定操作简易 3组继电器输出功能 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脉波触发电位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高输入频率: <5KHz 定位置范围: -199999 to 999999 second adjustabl 比较磁滞范围: 0 to 9999 adjustable 继电器容量: AC 250V-5A, DC 30V-7A 显示值范围: -199999 to 999999 显示幕: Red high efficiency LEDs high 9.2mm (.36") 参数设定方式: Touch switches 感应器电源: 12VDC +/-3%(<60mA) 记忆方式: Non-volatile E2PROM memory 绝缘耐压能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用环境条件: 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2014-12-03
上传用户：xjz632
特点 精确度0.25%滿刻度 ±1位數 输入配线系统可任意选择 CT比可任意设定 具有异常电流值与异常次数记录保留功能 电流过高或过低检测可任意设定 报警继电器复归方式可任意設定 尺寸小,穩定性高 2.主要規格 辅助电源: AC110V&220V ±20%(50 or 60Hz) AC220V&440V ±20%(50 or 60Hz)(optional) 精确度: 0.25% F.S. ±1 digit 输入负载: <0.2VA (Current) 最大过载能力 : Current related input: 2 x rated continuous 10 x rated 30 sec. 25 x rated 3sec. 50 x rated 1 sec. 输入电流范围: AC0-5A (10-1000Hz) CT ratio : 1-2000 adjustable 启动延迟动作时间: 0-99.9 second adjustable 继电器延迟动作时间: 0-99.9 second adjustable 继电器复归方式: Manual (N) / latch(L) can be modified 继电器磁滞范围: 0-999 digit adjustable 继电器动作方向: HI /LO/GO/HL can be modified 继电器容量: AC 250V-5A, DC 30V-7A 过载显示: "doFL" 温度系数: 50ppm/℃ (0-50℃) 显示幕: Red high efficiency LEDs high 14.22mm(.56")(PV) Red high efficiency LEDs high 14.22mm(.276")(NO) 参数设定方式: Touch switches 记忆型式 : Non-volatile E2PROM memory 绝缘耐压能力: 2KVac/1 min. (input/output/power) 1600Vdc(input/output 使用环境条件 : 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2013-10-14
上传用户：wanghui2438
特点 精确度0.1%滿刻度 ±1位數 可量測 交直流電流/交直流电压/電位計/傳送器/Pt-100/荷重元/電阻 等信号 显示范围-1999-9999可任意规划 具有异常值与异常次数记录保留功能 异常信号过高或过低或范围內或范围外检测可任意設定 报警继电器复归方式可任意設定 尺寸小,穩定性高 2.主要規格 精确度: 0.1% F.S. ±1 digit 0.2% F.S. ±1 digit(AC) 取样时间: 16 cycles/sec. 显示值范围: -1999 - +9999 digit adjustable 启动延迟动作时间: 0-99.9 second adjustable 继电器延迟动作时间: 0-99.9 second adjustable 继电器复归方式: Manual (N) / latch(L) can be modified 继电器动作方向: HI /LO/GO/HL can be modified 继电器容量: AC 250V-5A, DC 30V-7A 过载显示: "doFL" 温度系数: 50ppm/℃ (0-50℃) 显示幕: Red high efficiency LEDs high 14.22mm(.56")(PV) Red high efficiency LEDs high 7.0mm(.276")(NO) 参数设定方式: Touch switches 记忆型式 : Non-volatile E2PROM memory 绝缘耐压能力: 2KVac/1 min. (input/output/power) 1600Vdc(input/output 使用环境条件 : 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2013-11-02
上传用户：fandeshun
特点 最高輸入頻率 10KHz 计数速度 50/10000脈波/秒可选择 四种输入模式可选择(加算,減算,加減算,90度相位差加減算) 90度相位差加減算具有提高解析度4倍功能 输入脈波具有预设刻度功能 计数暂时停止功能 3组报警功能 15BIT类比输出功能 数位RS-485界面 2:主要規格 脈波輸入型式: Jump-pin selectable current sourcing(NPN) or current sinking (PNP) 脉波触发电位: HI bias (CMOS) (VIH=7.5V, VIL=5.5V) LO bias (TTL) (VIH=3.7V, VIL=2.0V) 最高输入频率: <10KHz (up,down,up/down mode) <3KHz (quadrature mode) 输出动作时间 : 0.1 to 99.9 second adjustable 输出复归方式: Manual(N) or automatic (R or C) can be modif 继电器容量: AC 250V-5A, DC 30V-7A 显示值范围: -199999 to 999999 类比输出解析度: 15 bit DAC 输出反应速度: < 1/f+10ms(0-90%) 输出负载能力: < 10mA for voltage mode < 10V for current mode <[(V+)-7.5V]/20mA for two-wire mode 输出之涟波: < 0.1% F.S. 通讯位址: "01"-"FF" 传输速度: 19200/9600/4800/2400 selective 通信协议: Modbus RTU mode 显示幕: Red high efficiency LEDs high 14.22mm (.56") 参数设定方式: Touch switches 感应器电源: 12VDC +/-3%(<60mA) 记忆方式: Non-volatile E2PROM memory 绝缘耐压能力: 2KVac/1 min. (input/output/power) 1600Vdc (input/output) 使用环境条件: 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2013-11-23
上传用户：redmoons
