CC386 is a general-purpose 32-bit C compiler. It is not an optimizing compiler but given that the code generation is fairly good. There are two versions one is for MSDOS/DPMI and one is for Win32. The Win32 version has a full-blown IDE capable of editing, building, and debugging windows programs included with it. However at this time debugging support for MSDOS is rudimentary at best and there is no IDE for DOS. the newest version, support windows.
标签： compiler general-purpose optimizing given
上传时间： 2015-04-12
上传用户：gtzj
prolog 找路例子程序： === === === === === === Part 1-Adding connections Part 2-Simple Path example | ?- path1(a,b,P,T). will produce the response: T = 15 P = [a,b] ? Part 3 - Non-repeating path As an example, the query: ?- path2(a,h,P,T). will succeed and may produce the bindings: P = [a,depot,b,d,e,f,h] T = 155 Part 4 - Generating a path below a cost threshold As an example, the query: ?- path_below_cost(a,[a,b,c,d,e,f,g,h],RS,300). returns: RS = [a,b,depot,c,d,e,g,f,h] ? RS = [a,c,depot,b,d,e,g,f,h] ? no ==================================
标签： Part connections example prolog
上传时间： 2015-04-24
上传用户：ljt101007
这是堆砖块的问题，输入砖块的堆砌情况，输出这堆砖块是否牢固，是就输出Yes，否则输出No。
标签：
上传时间： 2014-01-17
上传用户：lepoke
This project is created using the Keil ARM CA Compiler. The Logic Analyzer built into the simulator may be used to monitor and display any variable or peripheral I/O register. It is already configured to show the PWM output signal on PORT3.0 and PORT3.1 This ARM Example may be debugged using only the uVision Simulator and your PC--no additional hardware or evaluation boards are required. The Simulator provides cycle-accurate simulation of all on-chip peripherals of the ADuC7000 device series. You may create various input signals like digital pulses, sine waves, sawtooth waves, and square waves using signal functions which you write in C. Signal functions run in the background in the simulator within timing constraints you configure. In this example, several signal functions are defined in the included Startup_SIM.INI file.
标签： the Analyzer Compiler project
上传时间： 2013-12-19
上传用户：Yukiseop
cp0801_pathloss为UWB信道损耗计算函数，利用a=(c/(d^gamma))计算出信道增益，然后对函数的输入信号幅度进行变换得到输出结果。 cp0801_Gnoise1和cp0801_Gnoise2为产生AWGN的函数，分别为Eb/No和Ex/No条件下AWGN的产生
上传时间： 2013-12-17
上传用户：gxmm
This code detects memory leaks in embedded VC++ almost the same way crtdbg does in VC++. At the end of program execution it will display in the debug window if there were any memory leaks and how the memory looks so you can identify where your memory leak occurred. It will display in the debug window a message saying no memory leaks detected if there are no memory leaks. Similar to what crtdbg.h does in VC++. The code detects memory leaks generated with calls to new and delete operators in C++. The code doesn t detect memory leaks generated with C functions: malloc, calloc, free, but that can be done in the future. Let me know and I will program it.
标签： the embedded detects almost
上传时间： 2015-05-07
上传用户：comua
This m file models a DPSK UWB system using a delay in one leg of the mixer, correlation receiver low pass filter combination requiring no template for synching. Various waveforms are displayed throughout the system to allow the user to observe operation of the system.
标签： correlation receiver models system
上传时间： 2013-12-13
上传用户：semi1981
This a very simple Yee algorithm 3D FDTD code in C implementing the free space form of Maxwell s equations on a Cartesian grid. There are no internal materials or geometry. The code as delivered simulates an idealized rectangular waveguide by treating the interior of the mesh as free space/air and enforcing PEC (Perfect Electric Conductor) conditions on the faces of the mesh.
标签： implementing algorithm Maxwell simple
上传时间： 2015-05-14
上传用户：水中浮云
ARM下 Implement matrix multiplication of 2 square matrices, with data read from an input file and printed both to the console and to an output file. • Assume a file with correct data (no garbage, characters, etc.). • you must check and provide appropriate execution for 2 extra cases, namely when the matrix size given is either “0” , or when the size is greater than the maximum handled of “5” . In these 2 cases you must implement the following behaviour: o If size = 0, then print a message “Size = 0 is unacceptable” and continue by reading the next size for the next 2 matrices (if not end of file). o If size >5, then print two messages: “Size is too big - unacceptable”. Then read and discard the next (size2 ) integers and continue by reading the next size for the next 2 matrices (if not end of file).
标签： multiplication Implement matrices matrix
上传时间： 2014-08-30
上传用户：dsgkjgkjg
数字运算，判断一个数是否接近素数 A Niven number is a number such that the sum of its digits divides itself. For example, 111 is a Niven number because the sum of its digits is 3, which divides 111. We can also specify a number in another base b, and a number in base b is a Niven number if the sum of its digits divides its value. Given b (2 <= b <= 10) and a number in base b, determine whether it is a Niven number or not. Input Each line of input contains the base b, followed by a string of digits representing a positive integer in that base. There are no leading zeroes. The input is terminated by a line consisting of 0 alone. Output For each case, print "yes" on a line if the given number is a Niven number, and "no" otherwise. Sample Input 10 111 2 110 10 123 6 1000 8 2314 0 Sample Output yes yes no yes no
上传时间： 2015-05-21
上传用户：daguda
