Digitemp Jr. is a device that is designed to measure and report ambient temperature. When connected to an RS-232 port on any PC, it will periodically measure and report in ASCII form the ambient temperature in degrees Celsius. These temperature readings can be monitored with any terminal program. If the terminal program supports capture to disk, the temperature readings can be saved to disk for further analysis with a spreadsheet program or other data analysis tool. The simple ASCII output format of Digitemp Jr. makes it relatively easy to write custom software for receiving, recording, and analyzing ambient temperature data. Best of all, Digitemp Jr. requires no external power supplies or batteries. It is powered directly by the RS-232 port.
上传时间： 2013-10-20
上传用户：Maple
生活中许多目标的高度和水平距离需要进行测量。目前主要的测量方法，仍以传统的皮尺丈量为主，测量效率不高，有时还很不方便，没有技术成熟的数字式测高测距产品。以基本的数学方法为理论依据，利用遥控小车做为载体，采用角度传感器测量角度、霍尔传感器测量水平距离等，通过单片机LM3S615进行数据计算，实现了对待测目标物体的高度、水平距离等数据的快速、精确和数字式的测量，高度测量精度可达99.06%，水平测量精度则可达98.06%。 Abstract: In our lives， the height and horizontal distance of some goals are needed to be measured. Because the currently used methods are still traditional tape-based measuring methods， and the measuring efficiency is low and inconvenient so some kinds of digital and portable measuring methods or instruments are needed. Based on the basic math theory， this paper designed and manufactured a portable， digital and remote controlled measuring mobile small vehicle， which assembled with angle measuring sensor for angle measurement and Hall sensor for horizontal distance measuring. MCU LM3S615 calculated the height and horizontal distance data gotten from these sensors. The measuring process is simple， the measuring results are more accurate and the measuring efficiency is higher than traditional measure instruments. The accuracy of height and distance measurement can reach 99.06% and 98.06%.
上传时间： 2013-10-30
上传用户：jackandlee
为提高温度测量效率，降低系统的成本，扩展传输距离，设计出一种新型温度采集系统。单片机通过控制具有单总线方式的温度传感器DS18B20实现对温度的测量，同时单片机通过控制具有单总线方式300～450MHz频率范围内的MAX7044与MAX7033无线发射与接收芯片实现温度数据的无线传输。与传统温度采集系统相比，该系统利用单总线方式连接，采用无线传输方式实现远距离通信，易于系统的集成与扩展。实验结果表明，该系统结构简单、方便移植，能够同时实现多达上百点温度的测量与500m范围的传输。 Abstract: To improve the temperature measurement efficiency and reduce system cost,expansion of transmission distance,a new type of temperature acquisition system is designed.Microcontroller controlled temperature sensor DS18B20which has a single-bus achieves temperature measurement,while microcontroller by controlled the MAX7044and MAX7033chip with a single-bus and having300~450MHz radiofrequency to achieve the wireless transmission of temperature data.Compared with conventional temperature acquisition system,the system uses single-bus connected,and uses wireless transmission means to achieve long-distance communications,easy-to-system integration and expansion.The experimental results show that the system is simple,convenient transplantation,and can be implemented in as many as a hundred-point temperature measure-ment and the transmission range of500meters.
上传时间： 2013-10-29
上传用户：515414293
提出一种基于C8051F040的炮塔方位角测试系统的设计方案，给出测试系统的各个模块软硬件设计。炮塔方位角测试系统集数据采集，数据传输和数据显示等功能于一体，实现了炮塔方位角装置的离线检测。系统软件采用C51编写，对单片机进行有效电源管理，保证了系统的稳定性，可靠性。 Abstract: This paper puts forwards a design of artillery position system based on C8051F040，describes all modules hardware and software design of measurement system.The system has the function of information collection，transmission，and display.It can measure artillery position system in offline.The system software using C51can manage the power of single chip microcomputer，guarantee the stability，reliability.
上传时间： 2014-12-27
上传用户：7891
介绍了一种基于C8051F020单片机的多路压力测量仪。该测量仪选用电阻应变式压力传感器采集压力信号，并经放大电路处理后送入C8051F020单片机，再由C8051F020单片机内部的A/D转换器将采集到的压力信号进行模数转化，然后分别对数据进行存储和显示。该测量仪能测量6路压力信号，并且各测量点都能单独检测和设置。由于采用了C8051F020单片机，简化了硬件电路，增强了抗干扰能力，使得测量仪具有测量精度高，冲击小等特点。 Abstract: A measurement apparatus for multi-channel pressure based on single chip microcomputer is introduced.It can measure 6 channels signal of the pressure，and the pressure measure points can be detection and located individually.The pressure signal sampling is obtained by resistor stress-type pressure sensors，the digital signals of 6 channels are collected through amplifying and adjustment circuit of pressure signals and internal integrated A/D converter of MCU.Finally，and it realizes the function to store and display data separately.C8051F020 was used to made hardware circuit simple，and it also enhanced the anti-interference ability.It features high precision and little impact.
上传时间： 2013-11-16
上传用户：yare
介绍一种基于单片机的多路温度采集及监控系统，能够测量6路温度信号，具有计算机联网功能，各测量点可以单独监控和设置，可根据用户的需求自动控制。测量温度范围为-10 ℃～200 ℃，控制方式采用模拟量调压模式。该系统具有控制精度高、冲击小等特点。 Abstract: A temperature collecting and surveillance-controlling system based on sing-chip microcomputer is introduced. It can measure 6 channel signal of the temperature,and it has a function of network connection.The temperature measure points can be monitored and located, it can be controlled automatic according to user’s demand.The temperature range is -10℃ to 200℃.The model of control is adjustable voltage with simulation. It features high precision and little impact.
上传时间： 2013-10-23
上传用户：bjgaofei
为降低成本和解决现有膜片钳放大器系统中PC机的干扰问题，研究了一种基于单片机的膜片钳放大器小系统。该系统采用ADI公司生产的ADuC841作为控制核心，并且配置相应的液晶显示模块LCM3202401。模拟电路部分采用高输入阻抗的AD8627实现微电流信号的采集，并由后级电路进行信号的放大和电阻电容的补偿。它具有硬件电路简单、体积小、使用方便的特点。既可以单独作为小系统实现采集和显示，也可以通过红外方式和PC机进行通讯，在PC机上进行信号的处理。 Abstract: In order to reduce cost and resolve the interferential problem with PC in existing patch clamp amplifiers, a small patch clamp amplifier system design based on microcontroller is studied. It adopts a new high performance microconverter ADuC841 by the ADI as the control core in the system, configuring a liquid crystal module LCM3202401. In the analog circuit, AD8627 with high input impedance is used to detect the low current，signal magnification, as well as resistance and capacitance compensation are accomplished by subsequent circuits. It has the advantage of simple hardware circuit design, small volume and convenient operation. It can either be used as an independent system to measure and show signal detected or transmit to PC by infrared ray.
上传时间： 2013-11-06
上传用户：yy_cn
介绍了一种基于MSP430系列单片机和ADXL203加速度传感器的数字式倾角仪，它不仅可以实现水平度检测，而且可以测量00～3600范围内的任意倾角，分辨率可达O．1。。此外，由于该倾角仪输出为数字结果，因此它也可以与其他的数字设备结合起来，组合成一个功能更加强大的仪器。该数字倾角仪可广泛应用于建筑、机械、道路、桥梁、石油、煤矿和地质勘探等各种需要测量重力参考系下倾角的场合。关键词：MSP430F133单片机；力敏传感器；ADXL203加速度计；角度测量 Abstract：This paper presents a new style digital inclinometer which is developed on the basis of the MSP430F133 MCU and the ADXL203 dual axis aeeelerometer．This inclinometer not only can test levelness，but also can measure any angle between 0。and 360。with an accuracy of 0．1 O．In addition，its output is a digital result，which makes it possible to integrate itself with other digital devices to form a more functional unit．This inclinometer can be widely used in any construction site，oil field，coal-mine or geologic survey and SO on where it will provide the working people with convenience to measure any angles．Key words：MSP430F133 MCU；force sensor；ADXL203 accelerometer；angle measurement
上传时间： 2013-11-14
上传用户：lizhizheng88
基于LabVIEW和单片机的空调温度场测量系统的研究:室内温度是空调系统舒适性的重要指标,对其及时、准确地测量显得非常重要。介绍单片机AT89C51 和数字式、单总线型温度传感器DS18B20 组成矩形测量网络采集空调室内40 点温度,LabVIEW作为开发平台,二者之间通过串口实现数据通信,利用LabVIEW强大的数据处理和显示功能对采集的空调温度场数据进行实时处理、分析和显示,详细介绍了系统的硬件结构和软件模块的设计方案。关键词:单片机;DS18B20 ;LabVIEW;串行通信 Abstract : Temperature is a very important criterion of air condition system′s comfort , so it is very significant to measure it accurately and real timely. This paper int roduces a data acquisition system of measuring 40 point s temperature for air condition room based on single wire digital sensor DS18B20 and microcont roller AT89C51 which are composed of rectangle measuring meshwork. The data communication between LabVIEW and microcont roller is executed via serial port ,and the temperature field data of air condition room are processed analyzed and displayed on LabVIEW. The hardware and software modules are also given in detail.Keywords : single chip ;DS18B20 ;LabVIEW; serial communication
上传时间： 2014-05-05
上传用户：KSLYZ
单片机系统“PC”失控的软件措施Software measure of GettingO uto fC ontrolfo r“PC"in S ingleC hipC omputerS ystem谧 加 春 王 晓 基 雷 小 华(江 西 理 工 大 学机 电 工 程 学 院 ，赣 州 34 10 00)摘要单片机系统在实际工业现场中可能遇到各种干扰和自身的随机性故障。现场恶劣的环境有可能使计算机系统发生异常，计算机程序指针“PC”失控就是常见的故障之一，如果发生“PC”失控，将导致CPI工作混乱，酿成严重的事故。研究了“PC”失控的原因，并指出软件抗干扰的几种方法，有效保证单片机系统的正常工作。关键词单片机“PC”失控抗干扰Abstract Inp racticalin dustrialfi elds,th ereis v ariousin terferencea fectingo perationo fsi nglec hipc omputersy stemsa ndt hec omputersy stems。fac吨random faults饰themselves. It is very common that the severe environment makes the computer systems abnormal. The program counter "PC"gettingo utof co ntorlis on eo fth ec ommonfa ults.If th isoc curs,C PUw ouldb eru nningo utof or deran din torducesse riousan cient.T hec ausesof " PC"geting out of control， studied in this paper and some countermeasures of anti-interference师software are given to ensure single chip computer systemworking properly.Keywords Single。饰computer Porgramc ounter"P C" Anti-interfeernc 在设 计 和 开发单片机系统时，一般难以周全地预计单片机系统在实际工业现场中可能遇到的各种干扰和自身的随机性故障。因此，除了采取防止和抑制干扰的各项措施外，还应该借助于软件措施克服某些干扰，系统还应具备迅速自行恢复的能力。本文介绍的应对单片机系统PC失控的软件措施，设计灵活，节省硬件资源，能保证测控系统长期可靠地运行。MC S- 5 1单片机以其优良的性能价格比大量应用于工业现场测试和控制领域。但是，现场恶劣的环境有可能使计算机系统发生异常，计算机程序指针PC失控就是常见的故障之一，一旦发生PC“走飞”，计算机系统就会出现工作混乱，酿成严重的事故。为 了 在 CP 失控时尽量减少由此带来的不利影响，并尽快使系统恢复正常，需要采取一定的软件措施和硬件措施。常见的硬件措施有“看门狗”电路。软件措施设置的前提条件是:①在干扰作用下，微机系统硬件部分不会受到任何损坏，或者损坏部分设置有监测状态可供查询;②程序区不会受到干扰侵害。单片机系统的程序和表格以及重要的参数均设置在ROM区，不会因干扰的侵人而改变;③ RAM区中的重要数据不会被破坏，或者虽然被破坏，但是可以重新建立。
上传时间： 2013-11-02
上传用户：bhqrd30
