Write a Java program that demonstrates a high priority thread using sleep to give lower priority threads a chance to run
标签： priority demonstrates program thread
上传时间： 2013-12-06
上传用户：chenxichenyue
Design and test a category called Rectangle rectangular, rectangular attribute to the lower left corner of the upper-right corner and the coordinates of two points, to calculate the size of rectangular
标签： rectangular Rectangle attribute category
上传时间： 2013-12-09
上传用户：sssl
library which evaluates the lower tail of the noncentral Student s T distribution this is Applied Statistics Algorithm 5
标签： distribution noncentral evaluates the
上传时间： 2016-11-16
上传用户：xc216
lna lower noise amplifier
上传时间： 2014-01-13
上传用户：cxl274287265
This book bridges the gap between higher abstract modeling concepts and the lower-level programming aspects of embedded systems development. You gain a solid understanding of real-time embedded systems with detailed examples and industry wisdom.
标签： lower-level programming the abstract
上传时间： 2014-01-14
上传用户：yy541071797
These codes require an ASCII input file called input.dat of the following form: lower Limit on x Upper Limit on x Final Time Pressure for x<0 when t=0 Density for x<0 when t=0 Speed for x<0 when t=0 Pressure for x>0 when t=0 Density for x>0 when t=0 Speed for x>0 when t=0 These codes produce 8 ASCII output files: density.out. Density vs. x entropy.out. Entropy vs. x mach.out. Mach number vs. x massflux.out. Mass flux vs. x pressure.out. Pressure vs. x sound.out. Speed-of-sound vs. x velocity.out. Velocity vs. x waves.out. A description of the solution in terms of the three waves defined in the book (+,-,0).
标签： input following require called
上传时间： 2017-09-21
上传用户：希酱大魔王
The LTC®1966 is a true RMS-to-DC converter that uses aDS computational technique to make it dramatically simplerto use, significantly more accurate, lower in powerconsumption and more flexible than conventional logantilogRMS-to-DC converters. The LTC1966 RMS-to-DCconverter has an input signal range from 5mVRMS to1.5VRMS (a 50dB dynamic range with a single 5V supplyrail) and a 3dB bandwidth of 800kHz with signal crestfactors up to four.
上传时间： 2013-10-12
上传用户：qilin
ANALOG INPUT BANDWIDTH is a measure of the frequencyat which the reconstructed output fundamental drops3 dB below its low frequency value for a full scale input. Thetest is performed with fIN equal to 100 kHz plus integer multiplesof fCLK. The input frequency at which the output is −3dB relative to the low frequency input signal is the full powerbandwidth.APERTURE JITTER is the variation in aperture delay fromsample to sample. Aperture jitter shows up as input noise.APERTURE DELAY See Sampling Delay.BOTTOM OFFSET is the difference between the input voltagethat just causes the output code to transition to the firstcode and the negative reference voltage. Bottom Offset isdefined as EOB = VZT–VRB, where VZT is the first code transitioninput voltage and VRB is the lower reference voltage.Note that this is different from the normal Zero Scale Error.CONVERSION LATENCY See PIPELINE DELAY.CONVERSION TIME is the time required for a completemeasurement by an analog-to-digital converter. Since theConversion Time does not include acquisition time, multiplexerset up time, or other elements of a complete conversioncycle, the conversion time may be less than theThroughput Time.DC COMMON-MODE ERROR is a specification which appliesto ADCs with differential inputs. It is the change in theoutput code that occurs when the analog voltages on the twoinputs are changed by an equal amount. It is usually expressed in LSBs.
上传时间： 2013-11-12
上传用户：pans0ul
Abstract: Some types of loads require more current during startup than when running. Other loads can be limited to a lower-powercurrent during startup but require a higher operating current. This article describes an application circuit that automatically adjusts apower circuit’s overcurrent protection level up or down after startup is complete.
上传时间： 2013-10-23
上传用户：swaylong
The core voltages for FPGAs are moving lower as a resultof advances in the fabrication process. The newest FPGAfamily from Altera, the Stratix® II, now requires a corevoltage of 1.2V and the Stratix, Stratix GX, HardCopy®Stratix and CycloneTM families require a core voltage of1.5V. This article discusses how to power the core and I/Oof low voltage FPGAs using the latest step-down switchmode controllers from Linear Technology Corporation.
上传时间： 2013-10-08
上传用户：wangfei22
