This publication represents the largest LTC commitmentto an application note to date. No other application noteabsorbed as much effort, took so long or cost so much.This level of activity is justified by our belief that high speedmonolithic amplifiers greatly interest users.
标签： 高速放大器
上传时间： 2014-01-07
上传用户：wfl_yy
Sensors for pressure, load, temperature, acceleration andmany other physical quantities often take the form of aWheatstone bridge. These sensors can be extremely linearand stable over time and temperature. However, mostthings in nature are only linear if you don’t bend them toomuch. In the case of a load cell, Hooke’s law states that thestrain in a material is proportional to the applied stress—as long as the stress is nowhere near the material’s yieldpoint (the “point of no return” where the material ispermanently deformed).
上传时间： 2013-11-13
上传用户：墙角有棵树
设计了水声信号发生系统中的功率放大电路，可将前级电路产生的方波信号转换为正弦信号，同时进行滤波、功率放大，使其满足换能器对输入信号的要求。该电路以单片机AT89C52，集成6阶巴特沃思低通滤波芯片MF6以及大功率运算放大器LM12为核心，通过标准RS232接口与PC进行通信，实现信号增益的程控调节，对干扰信号具有良好的抑制作用。经调试该电路工作稳定正常，输出波形无失真，在输出功率以及放大增益、波纹系数等方面均满足设计要求。 This paper presented a design and implementation of underwater acoustic power amplifer. This circuit converted the rectangle signal generated by frontend circuit into the sine signal， then filtered and power amplification， it meets the requirements of the transducer.Included AT89C52， 6th order Butterworth filter MF6， hipower amplififier LM12.Communication with PC through the RS232 port. The signal gain is adjustable and could be remote controlled. It has a good inhibitory effect on the interference signal. After debugged， this circuit works stable， the output waveform has no distortion， it meets the design requirement in outprt power， amplifier gain and ripple factor.
上传时间： 2013-11-20
上传用户：qwe1234
PCI ExpressTM Architecture Add-in Card Compliance Checklist for the PCI Express Base 1.0a SpecificationThe PCI Special Interest Group disclaims all warranties and liability for the use of this document and the information contained herein and assumes no responsibility for any errors that may appear in this document, nor does the PCI Special Interest Group make a commitment to update the information contained herein.Contact the PCI Special Interest Group office to obtain the latest revision of this checklistQuestions regarding the ths document or membership in the PCI Special Interest Group may be forwarded tPCI Special Interest Group5440 SW Westgate Drive #217Portland, OR 97221Phone: 503-291-2569Fax: 503-297-1090 DISCLAIMERThis document is provided "as is" with no warranties whatsoever, including any warranty of merchantability, noninfringement, fitness for any particular purpose, or any warranty otherwise arising out of any proposal, specification, or sample. The PCI SIG disclaims all liability for infringement of proprietary rights, relating to use of information in this specification. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted herein.
标签： Architecture ExpressTM PCI
上传时间： 2013-11-03
上传用户：gy592333
Silicon Motion, Inc. has made best efforts to ensure that the information contained in this document is accurate andreliable. However, the information is subject to change without notice. No responsibility is assumed by SiliconMotion, Inc. for the use of this information, nor for infringements of patents or other rights of third parties.Copyright NoticeCopyright 2002, Silicon Motion, Inc. All rights reserved. No part of this publication may be reproduced, photocopied,or transmitted in any form, without the prior written consent of Silicon Motion, Inc. Silicon Motion, Inc. reserves theright to make changes to the product specification without reservation and without notice to our users
标签： GUIDELINES LAYOUT 320 PCB
上传时间： 2014-12-24
上传用户：zhaistone
Abstract: We can apply a BiCMOS integrated circuit with only resistors and no transistors to solve adifficult design problem. The mythically perfect operational amplifier's gain and temperature coefficient aredependent on external resistor values. Maxim precision resistor arrays are manufactured together on asingle die and then automatically trimmed, to ensure close ratio matching. This guarantees that theoperational amplifier (op amp) gain and temperature coefficient are predictable and reliable, even withlarge production volumes.
上传时间： 2014-11-30
上传用户：ynzfm
Easy-to-use and compact point-of-load power suppliesare necessary in systems with widely distributed, highcurrent, low voltage loads. The LTC®3415 provides acompact, simple and versatile solution. It includes a pairof integrated complementary power MOSFETs (32mΩtop and 25mΩ bottom) and requires no external senseresistor. A complete design requires an inductor andinput/output capacitors, and that’s it. The result is a fast,constant frequency, 7A current mode DC/DC switchingregulator.
上传时间： 2013-10-18
上传用户：avensy
Low power standby requirements are typically associatedwith battery-powered systems. Automotive systems,for example, commonly require power supplies tomaintain output voltage regulation even under no-loadconditions—while drawing minimal quiescent current topreserve battery life. Rising energy costs, however, haveextended the need for low current standby operation toline-powered systems, such as small plugged-in appliancesfor home and business.
上传时间： 2013-11-20
上传用户：xinyuzhiqiwuwu
Industrial remote monitoring systems and keep-alivecircuits spend most of their time in standby mode. Manyof these systems also depend on battery power, so powersupply effi ciency in standby state is very important tomaximize battery life. The LT®8410/-1 high effi ciencyboost converter is ideal for these systems, requiringonly 8.5μA of quiescent current in standby mode. Thedevice integrates high value (12.4M/0.4M) output feedbackresistors, signifi cantly reducing input current whenthe output is in regulation with no load. Other featuresinclude an integrated 40V switch and Schottky diode,output disconnect with current limit, built in soft-start,overvoltage protection and a wide input range, all in atiny 8-pin 2mm × 2mm DFN package.
上传时间： 2013-11-23
上传用户：新手无忧
Handheld electronic devices play a key role in our everydaylives. Because dependability is paramount, handhelds arecarefully engineered with lightweight power sources forreliable use under normal conditions. But no amount ofcareful engineering can prevent the mistreatment theywill undergo at the hands of humans. For example, whathappens when a factory worker drops a bar code scanner,causing the battery to pop out? Such events areelectronically unpredictable, and important data storedin volatile memory would be lost without some form ofsafety net—namely a short-term power holdup systemthat stores suffi cient energy to supply standby power untilthe battery can be replaced or the data can be stored inpermanent memory.
上传时间： 2013-11-05
上传用户：coeus
