SHUZIZHONG显示电路 源程序如下： #include <reg51.h>#include <intrins.h> unsigned char data dis_digit; unsigned char code dis_code[]={ 0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f,0x77,0x7c,0x39,0x5e,0x79,0x71};unsigned char data dis_buf[16];unsigned char data dis_index;char hour,min,sec,wang,year,mouth,day;unsigned char sec100;
上传时间： 2013-11-24
上传用户：fdmpy
#include <reg51.h>#include<intrins.h> #define BUSY1 (DQ1==0) sbit DQ1 = P0^4; unsigned char idata TMP; unsigned char idata TMP_d; unsigned char f; void wr_ds18_1(char dat);unsigned char rd_ds18_1(); /***************延时程序，单位us,大于10us*************/void time_delay(unsigned char time){ time=time-10; time=time/6; while(time!=0)time--;} /*****************************************************//* reset ds18b20 *//*****************************************************/void ds_reset_1(void){ unsigned char idata count=0; DQ1=0; time_delay(240); time_delay(240); DQ1=1; return;}
上传时间： 2013-10-29
上传用户：sssnaxie
EEPROM为ATMEL公司的AT24C01A。单片机为ATMEL公司的AT89C51。2. 软件说明 C语言为Franklin C V3.2。将源程序另存为testi2c.c，用命令C51 testi2c.cL51 TESTI2C.OBJOHS51 TESTI2C编译，连接，得到TESTI2C.HEX文件，即可由编程器读入并进行写片，实验。3．源程序#include <reg51.h>#include <intrins.h> #define uchar unsigned char#define uint unsigned int#define AddWr 0xa0 /*器件地址选择及写标志*/#define AddRd 0xa1 /*器件地址选择及读标志*/#define Hidden 0x0e /*显示器的消隐码*/
上传时间： 2013-10-09
上传用户：hjshhyy
数码管动态显示，菜用#include<intrins.h>头文件，才有右移的方式。控制数码管动态显示更灵活，方便
上传时间： 2016-11-10
上传用户：yepeng139
W29C040(512K FLASH)读写程序2007-09-10 11:16很是激动，去年用AT89S52捣弄了半年也没搞定，这次换成C8051f040，也不知道是天见我可怜还是狗运，终于把数据写进去了。想当时到处找的程序都没用，郁闷非常，这次走运成功，拿出来晒晒太阳（虽然也是该的别人的程序，但是好歹能用）。 /*W29C040(512K FLASH)读写程序*/ #include <c8051f040.h> #include <intrins.h> #include <absacc.h> sbit E=P1^0
上传时间： 2017-07-03
上传用户：wff
#include<reg52.h> #include<intrins.h> #define LED P0 sbit KEY0=P2^0; //定义按键输入端口 A sbit KEY1=P2^1; //定义按键输入端口 B sbit KEY2=P2^2; //定义按键输入端口 C unsigned int Led_table[8]={0xfe,0xfc,0xf8,0xf0,0xe0,0xc0,0x80,0x00}; char Led_num=0; unsigned int num=0; //中断计数 void delayms(unsigned int x) { unsigned int i,j;
标签： 单片机
上传时间： 2015-12-23
上传用户：kimyu
#include "STC90.h" #include < intrins.h > #define uchar unsigned char #define uint unsigned int #define led_port P1 sbit IR_RE = P3^2; sbit led_r = P1^3; sbit led_g = P1^4; sbit led_b = P1^5; sbit led_wd = P1^7; sbit K1 =P3^0 ; //增加键 sbit K2 =P3^1 ; //减少键 sbit BEEP =P3^7 ; //蜂鸣器 uchar temp,temp1; bit k=0; //红外解码判断标志位，为0则为有效信号，为1则为无效 bit Flag2; uchar date[4]={0,0,0,0}; //date数组为存放地址原码，反码，数据原码，反码 uint lade_1,lade_2,lade_3,lade_4; uint num; uchar date_ram,ee_temp,ee_temp1; uchar WDT_NUM=0; uchar const dofly[]={0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f};// 显示段码值01234567 uchar code seg[]={7,6,5,4,3,2,1,0};//分别对应相应的数码管点亮,即位码 unsigned long disp_date; void fade(); void fade1(); /*************************** 看门狗子程序*************************/ void watchdog_timer() { if(WDT_NUM==5) { WDT_NUM=0; led_wd=!led_wd; } WDT_NUM++; WDT_CONTR=0x3f; } /******************************************************************/ void delay(unsigned int cnt) { while(--cnt); } /*--------------------------延时1ms程子程序-----------------------*/ void delay_1ms(uint z) { uint x,y; for(x=z;x>0;x--) for(y=126;y>0;y--); } /*--------------------------延时1ms程子程序-----------------------*/ delay1000() { uchar i,j; i=5; do{j=95; do{j--;} while(j); i--; } while(i); } /*---------------------------延时882us子程序-----------------------*/ delay882() { uchar i,j; i=6; do{j=71; do{j--;} while(j); i--; }while(i); } /*--------------------------延时2400us程子程序-----------------------*/ delay2400() { uchar i,j; i=5; do{j=237; do{j--;} while(j); i--; }while(i); } /**********************************************************************/ /* void display() { uchar i; for(i=0;i<8;i++) { P0=dofly[disp_date%10];//取显示数据，段码 P2=seg[i]; //取位码 delay_1ms(1); disp_date/=10; } } */ /*********************************************************************/ uchar EEPROM_read(uint addr)//EEPROM字节读 { ISP_CONTR=0x83; //系统时钟<12M时，对ISP_CONTR寄存器设置的值，本电路为11.0592M ISP_CMD=1; //字节读 ISP_ADDRH=(addr&0xff00)>>8; ISP_ADDRL=addr&0x00ff; ISP_TRIG=0x46; ISP_TRIG=0xb9; _nop_(); _nop_(); return ISP_DATA; } //-------------------------------------------------------------------- void EEPROM_write(uint addr,uchar dat)//EEPROM字节写 { ISP_CONTR=0x83; //系统时钟<12M时，对ISP_CONTR寄存器设置的值，本电路为11.0592M ISP_CMD=2; //字节编程 ISP_ADDRH=(addr&0xff00)>>8; ISP_ADDRL=addr&0x00ff; ISP_DATA=dat; ISP_TRIG=0x46; ISP_TRIG=0xb9; _nop_(); _nop_(); } //-------------------------------------------------------------------- void EEPROM_ERASE(uint addr)//EEPROM扇区擦除 { ISP_CONTR=0x83; //系统时钟<12M时，对ISP_CONTR寄存器设置的值，本电路为11.0592M ISP_CMD=3; //扇区擦除 ISP_ADDRH=(addr&0xff00)>>8; ISP_ADDRL=addr&0x00ff; ISP_TRIG=0x46; ISP_TRIG=0xb9; _nop_(); _nop_(); } //************************************************************** /*----------------------------------------------------------*/ /*-----------------------红外解码程序(核心)-----------------*/ /*----------------------------------------------------------*/ void IR_decode() { uchar i,j; while(IR_RE==0); delay2400(); if(IR_RE==1) //延时2.4ms后如果是高电平则是新码 { delay1000(); delay1000(); for(i=0;i<4;i++) { for(j=0;j<8;j++) { while(IR_RE==0); //等待地址码第1位高电平到来 delay882(); //延时882us判断此时引脚电平 ///CY=IR_RE; if(IR_RE==0) { date[i]>>=1; date[i]=date[i]|0x00; } else if(IR_RE==1) { delay1000(); date[i]>>=1; date[i]=date[i]|0x80; } } //1位数据接收结束 } //32位二进制码接收结束 } } /* void LED_PWM() { lade_2=num; //384 lade_4=num; //384 while(lade_2!=0&Flag2==1) { for(lade_3=512;lade_3>lade_4;lade_3--) //512 { led_port=0x00; delay(1); } lade_3=512; //512 lade_4--; for(lade_1=0;lade_1<lade_2;lade_1++) { led_port=0x38; //c7 delay(1); } lade_1=0; lade_2--; if(temp!=0x0c&Flag2==1) { lade_2=0; } lade_2=num; //384 lade_4=num; //384 } } */ void calc() { EEPROM_read(0x2000); ee_temp1=ISP_DATA; ee_temp=ee_temp1&0x0f; //************************************* 1 /* if(date[3]==0xff&Flag2==1) { if(num>=20) { num=num-80; } //else num=1; LED_PWM(); } if(date[3]==0xfe&Flag2==1) { if(num<=500) { num=num+80; } // else num=511; LED_PWM(); } if(ee_temp1==0xfd) { led_port=0x00; watchdog_timer(); } if(ee_temp1==0xfc) { led_port=0x00; led_r=1; led_g=1; led_b=1; watchdog_timer(); } */ //********************************************** 2 if(ee_temp1==0xfb) { led_port=0x00; led_r=1; watchdog_timer(); } if(ee_temp1==0xfa) { led_port=0x00; led_g=1; watchdog_timer(); } if(ee_temp1==0xf9) { led_port=0x00; led_b=1; watchdog_timer(); } if(ee_temp1==0xf8) { led_port=0x00; led_r=1; led_g=1; led_b=1; watchdog_timer(); } //************************************** 3 if(ee_temp1==0xf7) { uint fade_1,fade_2,fade_3,fade_4; fade_2=448; //384 fade_4=448; //384 while(fade_2!=0&ee_temp==0x07) { for(fade_3=512;fade_3>fade_4;fade_3--) //512 { led_port=0x10; delay(1); } fade_3=512; //512 fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x08; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x07) { fade_2=0; } watchdog_timer(); fade_2=448; //384 fade_4=448; //384 } } if(ee_temp1==0xf6) { uint fade_1,fade_2,fade_3,fade_4; fade_2=448; //384 fade_4=448; //384 while(fade_2!=0&ee_temp==0x06) { for(fade_3=512;fade_3>fade_4;fade_3--) //512 { led_port=0x20; delay(1); } fade_3=512; //512 fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x10; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x06) { fade_2=0; } watchdog_timer(); fade_2=448; //384 fade_4=448; //384 } } if(ee_temp1==0xf5) { uint fade_1,fade_2,fade_3,fade_4; fade_2=448; //384 fade_4=448; //384 while(fade_2!=0&ee_temp==0x05) { for(fade_3=512;fade_3>fade_4;fade_3--) //512 { led_port=0x08; delay(1); } fade_3=512; //512 fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x20; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x05) { fade_2=0; } watchdog_timer(); fade_2=448; //384 fade_4=448; //384 } } if(ee_temp1==0xf4) { while(ee_temp==4) { led_port=0x00; led_r=1; delay_1ms(200); led_port=0x00; led_r=1; led_g=1; delay_1ms(200); led_port=0x00; led_g=1; delay_1ms(200); watchdog_timer(); led_port=0x00; led_g=1; led_b=1; delay_1ms(200); led_port=0x00; led_b=1; delay_1ms(200); led_port=0x00; led_b=1; led_r=1; delay_1ms(200); watchdog_timer(); } } //************************************** 4 if(ee_temp1==0xf3) { uint fade_1,fade_2,fade_3,fade_4; fade_2=416; //384 fade_4=416; //384 while(fade_2!=0&ee_temp==0x03) { for(fade_3=512;fade_3>fade_4;fade_3--) //512 { led_port=0x10; delay(1); } fade_3=512; //512 fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x08; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x03) { fade_2=0; } watchdog_timer(); fade_2=416; //384 fade_4=416; //384 } } if(ee_temp1==0xf2) { uint fade_1,fade_2,fade_3,fade_4; fade_2=384; //384 fade_4=384; //384 while(fade_2!=0&ee_temp==0x02) { for(fade_3=512;fade_3>fade_4;fade_3--) //512 { led_port=0x20; delay(1); } fade_3=512; //512 fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x10; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x02) { fade_2=0; } watchdog_timer(); fade_2=384; //384 fade_4=384; //384 } } if(ee_temp1==0xf1) { uint fade_1,fade_2,fade_3,fade_4; fade_2=348; //384 fade_4=348; //384 while(fade_2!=0&ee_temp==0x01) { for(fade_3=512;fade_3>fade_4;fade_3--) //512 { led_port=0x08; delay(1); } fade_3=512; //512 fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x20; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x01) { fade_2=0; } watchdog_timer(); fade_2=348; //384 fade_4=348; //384 } } if(ee_temp1==0xf0) { while(ee_temp==0) { led_port=0x00; led_r=1; delay_1ms(500); watchdog_timer(); led_port=0x00; led_g=1; delay_1ms(500); led_port=0x00; led_b=1; delay_1ms(500); watchdog_timer(); } } //******************************************** 5 if(ee_temp1==0xef) { uint fade_1,fade_2,fade_3,fade_4; fade_2=384; //384 fade_4=384; //384 while(fade_2!=0&ee_temp==0x0f) { for(fade_3=512;fade_3>fade_4;fade_3--) //512 { led_port=0x10; delay(1); } fade_3=512; //512 fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x08; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x0f) { fade_2=0; } watchdog_timer(); fade_2=384; //384 fade_4=384; //384 } } if(ee_temp1==0xee) { uint fade_1,fade_2,fade_3,fade_4; fade_2=320; //384 fade_4=320; //384 while(fade_2!=0&ee_temp==0x0e) { for(fade_3=512;fade_3>fade_4;fade_3--) //512 { led_port=0x20; delay(1); } fade_3=512; //512 fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x10; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x0e) { fade_2=0; } watchdog_timer(); fade_2=320; //384 fade_4=320; //384 } } if(ee_temp1==0xed) { uint fade_1,fade_2,fade_3,fade_4; fade_2=320; //384 fade_4=320; //384 while(fade_2!=0&ee_temp==0x0d) { for(fade_3=512;fade_3>fade_4;fade_3--) //512 { led_port=0x08; delay(1); } fade_3=512; //512 fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x20; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x0d) { fade_2=0; } watchdog_timer(); fade_2=320; //384 fade_4=320; //384 } } if(ee_temp1==0xec) fade(); //******************************************* 6 if(ee_temp1==0xeb) { led_port=0x00; led_r=1; led_g=1; watchdog_timer(); } if(ee_temp1==0xea) { led_port=0x00; //led_r=0; led_g=1; led_b=1; watchdog_timer(); } if(ee_temp1==0xe9) { led_port=0x00; led_r=1; //led_g=0; led_b=1; watchdog_timer(); } if(ee_temp1==0xe8) fade1(); } void fade() { // uchar i; uint fade_1,fade_2,fade_3,fade_4; fade_2=512; fade_4=511; while(fade_2!=0&ee_temp==0x0c) { for(fade_3=512;fade_3>fade_4;fade_3--) { led_port=0x10; delay(1); } fade_3=512; fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x08; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x0c) { fade_2=0; } } watchdog_timer(); fade_2=512; fade_4=511; while(fade_2!=0&ee_temp==0x0c) { if(ee_temp!=0x0c) { fade_2=0; } for(fade_3=512;fade_3>fade_4;fade_3--) { led_port=0x20; delay(1); // watchdog_timer(); } fade_3=512; fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x10; delay(1); // watchdog_timer(); } fade_1=0; fade_2--; } watchdog_timer(); fade_2=512; fade_4=511; while(fade_2!=0&ee_temp==0x0c) { if(ee_temp!=0x0c) { fade_2=0; } for(fade_3=512;fade_3>fade_4;fade_3--) { led_port=0x08; delay(1); watchdog_timer(); } fade_3=512; fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x20; delay(1); watchdog_timer(); } fade_1=0; fade_2--; } watchdog_timer(); } void fade1() { // uchar i; uint fade_1,fade_2,fade_3,fade_4; fade_2=128; fade_4=127; while(fade_2!=0&ee_temp==0x08) { for(fade_3=128;fade_3>fade_4;fade_3--) { led_port=0x10; delay(1); } fade_3=128; fade_4--; for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x08; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x08) { fade_2=0; } } watchdog_timer(); fade_2=128; fade_4=127; while(fade_2!=0&ee_temp==0x08) { if(ee_temp!=0x08) { fade_2=0; } for(fade_3=128;fade_3>fade_4;fade_3--) { led_port=0x20; delay(1); } fade_3=128; fade_4--; for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x10; delay(1); } fade_1=0; fade_2--; } watchdog_timer(); fade_2=128; fade_4=127; while(fade_2!=0&ee_temp==0x08) { if(ee_temp!=0x08) { fade_2=0; } for(fade_3=128;fade_3>fade_4;fade_3--) { led_port=0x08; delay(1); } fade_3=128; fade_4--; for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x20; delay(1); } fade_1=0; fade_2--; } watchdog_timer(); } void init() { led_port=0x00; /* led_r=1; delay_1ms(500); led_port=0x00; led_g=1; delay_1ms(500); led_port=0x00; led_b=1; delay_1ms(500); led_port=0x00; */ delay_1ms(2); WDT_CONTR=0x3f; delay_1ms(500); } //******************************** void main() { init(); Flag2=0; SP=0x60; //堆栈指针 EX0=1; //允许外部中断0,用于检测红外遥控器按键 EA=1; num=255; while(1) { calc(); } } //******************************************************************** /*------------------------外部中断0程序-------------------------*/ /*------------------主要用于处理红外遥控键值--------------------*/ void int0() interrupt 0 { uchar i; Flag2=0; /////// k=0; EX0=0; //检测到有效信号关中断，防止干扰 for(i=0;i<4;i++) { delay1000(); if(IR_RE==1){k=1;} //刚开始为9ms的引导码. } led_port=0x00; if(k==0) { IR_decode(); //如果接收到的是有效信号，则调用解码程序 if(date[3]>=0xe8) { if(date[3]<=0xfb) { temp1=date[3]; EEPROM_ERASE(0x2000); //STC_EEROM_0X2000 temp1 EEPROM_write(0x2000,temp1); EEPROM_read(0x2000); ee_temp1=ISP_DATA; ee_temp=ee_temp1&0x0f; /* temp=date[3]&0x0f; EEPROM_ERASE(0x2004); //STC_EEROM_0X2004 temp EEPROM_write(0x2004,temp); */ } else { EEPROM_read(0x2000); ee_temp1=ISP_DATA; ee_temp=ee_temp1&0x0f; } } delay2400(); delay2400(); delay2400(); delay_1ms(500); } EX0=1; //开外部中断，允许新的遥控按键 }
上传时间： 2016-07-02
上传用户：184890962
/****************temic*********t5557***********************************/ #include <at892051.h> #include <string.h> #include <intrins.h> #include <stdio.h> #define uchar unsigned char #define uint unsigned int #define ulong unsigned long //STC12C2051AD的SFR定义 sfr WDT_CONTR = 0xe1;//stc2051的看门狗?????? /**********全局常量************/ //写卡的命令 #define write_command0 0//写密码 #define write_command1 1//写配置字 #define write_command2 2//密码写数据 #define write_command3 3//唤醒 #define write_command4 4//停止命令 #define TRUE 1 #define FALSE 0 #define OK 0 #define ERROR 255 //读卡的时间参数us #define ts_min 250//270*11.0592/12=249//取近似的整数 #define ts_max 304//330*11.0592/12=304 #define t1_min 73//90*11.0592/12=83:-10调整 #define t1_max 156//180*11.0592/12=166 #define t2_min 184//210*11.0592/12=194 #define t2_max 267//300*11.0592/12=276 //***********不采用中断处理:采用查询的方法读卡时关所有中断****************/ sbit p_U2270B_Standby = P3^5;//p_U2270B_Standby PIN=13 sbit p_U2270B_CFE = P3^3;//p_U2270B_CFE PIN=6 sbit p_U2270B_OutPut = P3^7;//p_U2270B_OutPut PIN=2 sbit wtd_sck = P1^7;//SPI总线 sbit wtd_si = P1^3; sbit wtd_so = P1^2; sbit iic_data = P1^2;//lcd IIC sbit iic_clk = P1^7; sbit led_light = P1^6;//测试绿灯 sbit led_light1 = P1^5;//测试红灯 sbit led_light_ok = P1^1;//读卡成功标志 sbit fengmingqi = P1^5; /***********全局变量************************************/ uchar data Nkey_a[4] = {0xA0, 0xA1, 0xA2, 0xA3};//初始密码 //uchar idata card_snr[4]; //配置字 uchar data bankdata[28] = {1,2,3,4,5,6,7,1,2,3,4,5,6,7,1,2,3,4,5,6,7,1,2,3,4,5,6,7}; //存储卡上用户数据(1-7)7*4=28 uchar data cominceptbuff[6] = {1,2,3,4,5,6};//串口接收数组ram uchar command; //第一个命令 uchar command1;// //uint temp; uchar j,i; uchar myaddr = 8; //uchar ywqz_count,time_count; //ywqz jishu: uchar bdata DATA; sbit BIT0 = DATA^0; sbit BIT1 = DATA^1; sbit BIT2 = DATA^2; sbit BIT3 = DATA^3; sbit BIT4 = DATA^4; sbit BIT5 = DATA^5; sbit BIT6 = DATA^6; sbit BIT7 = DATA^7; uchar bdata DATA1; sbit BIT10 = DATA1^0; sbit BIT11 = DATA1^1; sbit BIT12 = DATA1^2; sbit BIT13 = DATA1^3; sbit BIT14 = DATA1^4; sbit BIT15 = DATA1^5; sbit BIT16 = DATA1^6; sbit BIT17 = DATA1^7; bit i_CurrentLevel;//i_CurrentLevel BIT 00H(Saves current level of OutPut pin of U2270B) bit timer1_end; bit read_ok = 0; //缓存定时值,因用同一个定时器 union HLint { uint W; struct { uchar H;uchar L; } B; };//union HLint idata a union HLint data a; //缓存定时值,因用同一个定时器 union HLint0 { uint W; struct { uchar H; uchar L; } B; };//union HLint idata a union HLint0 data b; /**********************函数原型*****************/ //读写操作 void f_readcard(void);//全部读出1~7 AOR唤醒 void f_writecard(uchar x);//根据命令写不同的内容和操作 void f_clearpassword(void);//清除密码 void f_changepassword(void);//修改密码 //功能子函数 void write_password(uchar data *data p);//写初始密码或数据 void write_block(uchar x,uchar data *data p);//不能用通用指针 void write_bit(bit x);//写位 /*子函数区*****************************************************/ void delay_2(uint x) //延时,时间x*10us@12mhz,最小20us@12mhz { x--; x--; while(x) { _nop_(); _nop_(); x--; } _nop_();//WDT_CONTR=0X3C;不能频繁的复位 _nop_(); } ///////////////////////////////////////////////////////////////////// void initial(void) { SCON = 0x50; //串口方式1,允许接收 //SCON =0x50; //01010000B:10位异步收发,波特率可变,SM2=0不用接收到有效停止位才RI=1, //REN=1允许接收 TMOD = 0x21; //定时器1 定时方式2(8位),定时器0 定时方式1(16位) TCON = 0x40; //设定时器1 允许开始计时(IT1=1) TH1 = 0xfD; //FB 18.432MHz 9600 波特率 TL1 = 0xfD; //fd 11.0592 9600 IE = 0X90; //EA=ES=1 TR1 = 1; //启动定时器 WDT_CONTR = 0x3c;//使能看门狗 p_U2270B_Standby = 0;//单电源 PCON = 0x00; IP = 0x10;//uart you xian XXXPS PT1 PX1 PT0 PX0 led_light1 = 1; led_light = 0; p_U2270B_OutPut = 1; } /************************************************/ void f_readcard()//读卡 { EA = 0;//全关,防止影响跳变的定时器计时 WDT_CONTR = 0X3C;//喂狗 p_U2270B_CFE = 1;// delay_2(232); //>2.5ms /* // aor 用唤醒功能来防碰撞 p_U2270B_CFE = 0; delay_2(18);//start gap>150us write_bit(1);//10=操作码读0页 write_bit(0); write_password(&bankdata[24]);//密码block7 p_U2270B_CFE =1 ;// delay_2(516);//编程及确认时间5.6ms */ WDT_CONTR = 0X3C;//喂狗 led_light = 0; b.W = 0; while(!(read_ok == 1)) { //while(p_U2270B_OutPut);//等一个稳定的低电平?超时判断? while(!p_U2270B_OutPut);//等待上升沿的到来同步信号检测1 TR0 = 1; //deng xia jiang while(p_U2270B_OutPut);//等待下降沿 TR0 = 0; a.B.H = TH0; a.B.L = TL0; TH0 = TL0 = 0; TR0 = 1;//定时器晚启动10个周期 //同步头 if((324 < a.W) && (a.W < 353)) ;//检测同步信号1 else { TR0 = 0; TH0 = TL0 = 0; goto read_error; } //等待上升沿 while(!p_U2270B_OutPut); TR0 = 0; a.B.H = TH0; a.B.L = TL0; TH0 = TL0 = 0; TR0 = 1;//b.N1<<=8; if(a.B.L < 195);//0.5p else { TR0 = 0; TH0 = TL0 = 0; goto read_error; } //读0~7块的数据 for(j = 0;j < 28;j++) { //uchar i; for(i = 0;i < 16;i++)//8个位 { //等待下降沿的到来 while(p_U2270B_OutPut); TR0 = 0; a.B.H = TH0; a.B.L = TL0; TH0 = TL0 = 0; TR0 = 1; if(t2_max < a.W/*)&&(a.W < t2_max)*/)//1P { b.W >>= 2;//先左移再赋值 b.B.L += 0xc0; i++; } else if(t1_min < a.B.L/*)&&(a.B.L < t1_max)*/)//0.5p { b.W >>= 1; b.B.L += 0x80; } else { TR0 = 0; TH0 = TL0 = 0; goto read_error; } i++; while(!p_U2270B_OutPut);//上升 TR0 = 0; a.B.H = TH0; a.B.L = TL0; TH0 = TL0 = 0; TR0 = 1; if(t2_min < a.W/*)&&(a.W < t2_max)*/)//1P { b.W >>= 2; i++; } else if(t1_min < a.B.L/*a.W)&&(a.B.L < t1_max)*/)//0.5P //else if(!(a.W==0)) { b.W >>= 1; //temp+=0x00; //led_light1=0;led_light=1;delay_2(40000); } else { TR0 = 0; TH0 = TL0 = 0; goto read_error; } i++; } //取出奇位 DATA = b.B.L; BIT13 = BIT7; BIT12 = BIT5; BIT11 = BIT3; BIT10 = BIT1; DATA = b.B.H; BIT17 = BIT7; BIT16 = BIT5; BIT15 = BIT3; BIT14 = BIT1; bankdata[j] = DATA1; } read_ok = 1;//读卡完成了 read_error: _nop_(); } } /***************************************************/ void f_writecard(uchar x)//写卡 { p_U2270B_CFE = 1; delay_2(232); //>2.5ms //psw=0 standard write if (x == write_command0)//写密码:初始化密码 { uchar i; uchar data *data p; p = cominceptbuff; p_U2270B_CFE = 0; delay_2(31);//start gap>330us write_bit(1);//写操作码1:10 write_bit(0);//写操作码0 write_bit(0);//写锁定位0 for(i = 0;i < 35;i++) { write_bit(1);//写数据位1 } p_U2270B_CFE = 1; led_light1 = 0; led_light = 1; delay_2(40000);//测试使用 //write_block(cominceptbuff[4],p); p_U2270B_CFE = 1; bankdata[20] = cominceptbuff[0];//密码存入 bankdata[21] = cominceptbuff[1]; bankdata[22] = cominceptbuff[2]; bankdata[23] = cominceptbuff[3]; } else if (x == write_command1)//配置卡参数:初始化 { uchar data *data p; p = cominceptbuff; write_bit(1);//写操作码1:10 write_bit(0);//写操作码0 write_bit(0);//写锁定位0 write_block(cominceptbuff[4],p); p_U2270B_CFE= 1; } //psw=1 pssword mode else if(x == write_command2) //密码写数据 { uchar data*data p; p = &bankdata[24]; write_bit(1);//写操作码1:10 write_bit(0);//写操作码0 write_password(p);//发口令 write_bit(0);//写锁定位0 p = cominceptbuff; write_block(cominceptbuff[4],p);//写数据 } else if(x == write_command3)//aor //唤醒 { //cominceptbuff[1]操作码10 X xxxxxB uchar data *data p; p = cominceptbuff; write_bit(1);//10 write_bit(0); write_password(p);//密码 p_U2270B_CFE = 1;//此时数据不停的循环传出 } else //停止操作码 { write_bit(1);//11 write_bit(1); p_U2270B_CFE = 1; } p_U2270B_CFE = 1; delay_2(560);//5.6ms } /************************************/ void f_clearpassword()//清除密码 { uchar data *data p; uchar i,x; p = &bankdata[24];//原密码 p_U2270B_CFE = 0; delay_2(18);//start gap>150us //操作码10:10xxxxxxB write_bit(1); write_bit(0); for(x = 0;x < 4;x++)//发原密码 { DATA = *(p++); for(i = 0;i < 8;i++) { write_bit(BIT0); DATA >>= 1; } } write_bit(0);//锁定位0:0 p = &cominceptbuff[0]; write_block(0x00,p);//写新配置参数:pwd=0 //密码无效:即清除密码 DATA = 0x00;//停止操作码00000000B for(i = 0;i < 2;i++) { write_bit(BIT7); DATA <<= 1; } p_U2270B_CFE = 1; delay_2(560);//5.6ms } /*********************************/ void f_changepassword()//修改密码 { uchar data *data p; uchar i,x,addr; addr = 0x07;//block7 p = &Nkey_a[0];//原密码 DATA = 0x80;//操作码10:10xxxxxxB for(i = 0;i < 2;i++) { write_bit(BIT7); DATA <<= 1; } for(x = 0;x < 4;x++)//发原密码 { DATA = *(p++); for(i = 0;i < 8;i++) { write_bit(BIT7); DATA >>= 1; } } write_bit(0);//锁定位0:0 p = &cominceptbuff[0]; write_block(0x07,p);//写新密码 p_U2270B_CFE = 1; bankdata[24] = cominceptbuff[0];//密码存入 bankdata[25] = cominceptbuff[1]; bankdata[26] = cominceptbuff[2]; bankdata[27] = cominceptbuff[3]; DATA = 0x00;//停止操作码00000000B for(i = 0;i < 2;i++) { write_bit(BIT7); DATA <<= 1; } p_U2270B_CFE = 1; delay_2(560);//5.6ms } /***************************子函数***********************************/ void write_bit(bit x)//写一位 { if(x) { p_U2270B_CFE = 1; delay_2(32);//448*11.0592/120=42延时448us p_U2270B_CFE = 0; delay_2(28);//280*11.0592/120=26写1 } else { p_U2270B_CFE = 1; delay_2(92);//192*11.0592/120=18 p_U2270B_CFE = 0; delay_2(28);//280*11.0592/120=26写0 } } /*******************写一个block*******************/ void write_block(uchar addr,uchar data *data p) { uchar i,j; for(i = 0;i < 4;i++)//block0数据 { DATA = *(p++); for(j = 0;j < 8;j++) { write_bit(BIT0); DATA >>= 1; } } DATA = addr <<= 5;//0地址 for(i = 0;i < 3;i++) { write_bit(BIT7); DATA <<= 1; } } /*************************************************/ void write_password(uchar data *data p) { uchar i,j; for(i = 0;i < 4;i++)// { DATA = *(p++); for(j = 0;j < 8;j++) { write_bit(BIT0); DATA >>= 1; } } } /*************************************************/ void main() { initial(); TI = RI = 0; ES = 1; EA = 1; delay_2(28); //f_readcard(); while(1) { f_readcard(); //读卡 f_writecard(command1); //写卡 f_clearpassword(); //清除密码 f_changepassword(); //修改密码 } }
标签： 12345
上传时间： 2017-10-20
上传用户：my_lcs
300个C51单片机设计proteus仿真源码软件源码:100000秒以内的计时程序10秒的秒表12864LCD图形滚动演示128X64LED160128LCD图文演示1602字符液晶滚动演示程序1602液晶显示的DS1302实时时钟16×16点阵(滚动显示)16×16点阵2(滚动显示)2io5键盘模拟音量数码管显示2×20串行字符液晶演示32x16汉字44行列键盘485全双工通信4×4键盘矩阵控制条形LED显示4个独立式按键控制LED开关4个独立式按键控制LED移位4只数码管滚动显示0~3555可调PWM发生器555的应用6264扩展内存6个16×16点阵74HC154译码器应用74HC59574HC595串入并出芯片应用74LS138译码器应用74LS148扩展中断8051双机通信简例8255并行口扩展实例89C51PWM8x8LED汉字显示8x8点阵做的贪吃蛇游戏8×8LED点阵屏显示数字8只数码管同时显示不同字符8只数码管显示多个不同字符8只数码管滚动显示8~F8只数码管滚动显示单个数字8只数码管滚动显示数字串8只数码管闪烁显示8通道自动温度检测系统仿真（含原程序）ADC0808 PWM实验ADC0809模数转换与显示ADC0832模数转换与显示AT89C51对直流电动机的驱动AVR_UartBCD译码数码管显示数字c51 可预设电压的数控电源（功能强大）clockConterCPU控制的独立式键盘扫描实验da、ad。液晶，传递函数模型综合应用的实例DIY51式数控电源DS1621温度传感器实验ds18b20DS18B20温度传感器实验DS18B20温度检测及其液晶显示HorseLightI2CIIC-24C04与数码管IIC-24C04与蜂鸣器INT0与INT1中断计数INT0中断3位计数INT0及INT1中断计数INT0和INT1控制条形LEDINT1中断5位计数IO并行口直接驱动单个数码管K1-K4 分组控制LEDK1-K4 控制LED移位K1-K4 控制数码管加减演示K1-K4 控制数码管移位显示K1-K4 键状态显示key_lcdks0108 液晶12864LCD频率计仿真LED代码查询V1[1].1LED模拟交通灯LED闪烁M16_AN_CompareM16_EEPROMM16_HorseMAX7221控制数码管动态显示my16key_cNT0中断控制LEDNT0中断计数NumberDisplayP3口流水灯PCF8574PCF8583+LCD1602PCF8591模数与数模转换实验proteus ADDC的练习程序PWMPWMLEDPWM控制LED的亮度仿真程序PWM控制马达的方法PWM波输出（可调）PWM电机正反转pwm程序实例PWM调温RAM扩展练习sscom32串口调试TIMER0与TIMER1控制条形LEDTIMER0控制LED二进制计数TIMER0控制单只LED闪烁TIMER0控制四只LED滚动闪烁TIMER0控制流水灯ULN2803usart_t《lcd1602仿真实例》一个数控直流稳压电源一个步进电机的仿真一步一步教你51_PC串口通信万能逻辑电路实验三机通讯串口仿真mcu_pc串口方式1串行数据转换为并行数据交通灯从左到右的流水灯光藕隔离驱动电机内部函数intrins.h应用举例净水控制器仿真电路刚做好的十个字的led屏模拟有程序包含单片机寄存器的头文件单只按键控制单只数码管滚动显示单只数码管循环显示0-9单只数码管循环显示0~F单片机与PC机串口通讯仿真单片机之间双向通信单片机向PC发送数据单片机向主机发送字符串单片机接收PC发出的数据单片机控制的电动自行车驱动系统单片机数据发送程序发一个用定时器做的PWM基于1602+ds12b80+ds1302+音乐+电子书+流水灯的多功能电子表基于ADC0832的数字电压表基于AT24C02的多机通信基于AT89C51+MAX7219的频率计 附带proteus仿真电路图 实际硬件电路测试通过基于DS1302的日历时钟基于yjwpm测试过的DS18B20仿真实例多功能电子钟多点温度测量多路开关状态指示大屏幕仿真子电路做的一个H型电机驱动电路字符串函数string.h应用举例字符函数ctype.h应用举例宏定义应用举例定时器中断控制的独立式键盘扫描实验定时器控制交通指示灯定时器控制数码动态显示定时器控制数码管动管显示对I2C总线上挂接多个AT24C0
上传时间： 2021-10-27
上传用户：wangshoupeng199
#nclude<reg51.h>#include<intrins.h>#销nclude<math.h>#include<string.h>struct PID{unsigned int SetPoint；//设定目标 Desired Value unsigned int Proportion；//比例常数Proportional Const unsigned int integral；//积分常数Integral Const unsigned int Derivative://微分常数Derivative Const unsigned int LastError；//Emorl-1]unsigned int PrevError；//Errorl-2]unsigned int SumError；//Sums of Errors struct PID spid；//PID Control Structure unsigned int rout；//PID Response（Output）unsigned int rin://PID Feedback（Input）sbit data1=P100；sbit clk=P141；sbit plus=P240；sbit subs=P241：sbit stop=P22；sbit output=P34；sbit DQ=P33；unsigned char flag，flag_1=0；unsigned char high_time，low_time，.count=0，/占空比调节参数unsigned char set_temper=35；unsigned char temper；unsigned chari：unsigned charj=0；unsigned ints；
上传时间： 2022-07-02
上传用户：xsr1983
