NXP Semiconductor designed the LPC2400 microcontrollers around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interFaces that include both JTAG andembedded Trace. The LPC2400 microcontrollers have 512 kB of on-chip high-speedFlash memory. This Flash memory includes a special 128-bit wide memory interface andaccelerator architecture that enables the CPU to execute sequential instructions fromFlash memory at the maximum 72 MHz system clock rate. This feature is available onlyon the LPC2000 ARM Microcontroller family of products. The LPC2400 can execute both32-bit ARM and 16-bit Thumb instructions. Support for the two Instruction Sets meansEngineers can choose to optimize their application for either performance or code size atthe sub-routine level. When the core executes instructions in Thumb state it can reducecode size by more than 30 % with only a small loss in performance while executinginstructions in ARM state maximizes core performance.
上传时间： 2013-11-15
上传用户：zouxinwang
Abstract: This application note explains the hardware of different types of 1-Wire® interFaces and software examples adapted to this hardware with a focus on serial ports. Depending on the types of iButtons required for a project and the type of computer to be used, the most economical interface is easily found. The hardware examples shown are basically two different types: 5V general interface and 12V RS-232 interface. Within the 5V group a common printed circuit board could be used for all circuits described. The variations can be achieved by different populations of components. The same principal is used for the 12V RS-232 interface. The population determines if it is a Read all or a Read/Write all type of interface. There are other possible circuit implementations to create a 1-Wire interface. The circuits described in this application note cover many different configurations. For a custom application, one of the described options can be adapted to meet individual needs.
标签： iButtons Reading Writing and
上传时间： 2013-10-29
上传用户：long14578
摘 要 瞬态仿真领域的许多工作需要获得可视化数据, 仿真电路不能将输出参数绘制成图形时研究工作将受到很大影响. 而权威电路仿真软件PSpice 在这个方面不尽如人意. 本文提出了一种有效的解决办法: 通过MATLAB 编程搭建一个PSpice 与MATLAB 的数据接口,使PSpice输出数据文件可以导入到MATLAB中绘制图形. 这令我们能够很方便地获得数据的规律以有效地分析仿真结果, 这项技术对于教学和工程实践都有比较实际的帮助.关键词: 瞬态仿真 仿真程序 PSpice MATLAB 可视化数据The Data Transfer from Pspice to MATLABWu hao Ning yuanzhong Liang yingAbstract Many works in the area of transient simulation has shown how a emulator such asPSpice can be interfaced to an control analysis package such as MATLAB to get viewdata. Thepaper describes how such interFaces can be made using the MATLAB programming. The platformas a typical platform will solve the problem that PSpice software sometimes can not draw the datato a picture. It can make us find the rule from numerous data very expediently, so we can analyzethe outcome of the simulation. And it also can be used in the field of education.Keywords Transient Simulation Emulator PSpice MATLAB Viewdata1 引言科学研究和工程应用常需要进行电路仿真 PSpice可进行直流 交流 瞬态等基本电路特性分析 也可进行蒙托卡诺 MC 统计分析 最坏情况 Wcase 分析 优化设计等复杂电路特性分析 它是国际上仿真电路的权威软件 而MATLAB的主要特点有 高效方便的矩阵和数组运算 编程效率高 结构化面向对象 方便的绘图功能 用户使用方便 工具箱功能强大 两者各有着重点 两种软件结合应用 对研究工作有很重要的意义香港理工大学Y. S. LEE 等人首先将PSpice和MATLAB结合 开发了电力电子电路优化用的CAD 程序MATSPICE[6] 将两者相结合的关键在于 如何用MATLAB 获取PSpice的仿真数据 对此参考文献 6 里没有详细叙述 本文着重说明用MATLAB 读取PSpice仿真数据的具体方法本论文利用MATLAB对PSpice仿真出的数据处理绘制出后者无法得到或是效果不好的仿真图形 下面就两者结合使用的例子 进行具体说明
上传时间： 2013-10-20
上传用户：wuchunzhong
The exacting technological demands created byincreasing bandwidth requirements have given riseto significant advances in FPGA technology thatenable engineers to successfully incorporate highspeedI/O interFaces in their designs. One aspect ofdesign that plays an increasingly important role isthat of the FPGA package. As the interFaces get fasterand wider, choosing the right package has becomeone of the key considerations for the systemdesigner.
上传时间： 2013-10-22
上传用户：1234xhb
Consumer display applications commonly use high-speed LVDS interFaces to transfer videodata. Spread-spectrum clocking can be used to address electromagnetic compatibility (EMC)issues within these consumer devices. This application note uses Spartan®-6 FPGAs togenerate spread-spectrum clocks using the DCM_CLKGEN primitive.
上传时间： 2014-12-28
上传用户：yan2267246
The Tri-Mode Ethernet MAC (TEMAC) UltraController-II module is a minimal footprint,embedded network processing engine based on the PowerPC™ 405 (PPC405) processor coreand the TEMAC core embedded within a Virtex™-4 FX Platform FPGA. The TEMACUltraController-II module connects to an external PHY through Gigabit Media IndependentInterface (GMII) and Management Data Input/Output (MDIO) interFaces and supports tri-mode(10/100/1000 Mb/s) Ethernet. Software running from the processor cache reads and writesthrough an On-Chip Memory (OCM) interface to two FIFOs that act as buffers between thedifferent clock domains of the PPC405 OCM and the TEMAC.
上传时间： 2013-10-26
上传用户：yuzsu
In today’s world of modular networking and telecommunications design, it is becomingincreasingly difficult to keep alignment with the many different and often changing interFaces,both inter-board and intra-board. Each manufacturer has their own spin on the way in whichdevices are connected. To satisfy the needs of our customers, we must be able to support alltheir interface requirements. For us to be able to make products for many customers, we mustadopt a modular approach to the design. This modularity is the one issue that drives the majorproblem of shifting our bits from one modular interface to another.
上传时间： 2013-11-25
上传用户：suicone
A Computer-On-Module, or COM, is a Module with all components necessary for a bootable host computer, packaged as a super component. A COM requires a Carrier Board to bring out I/O and to power up. COMs are used to build single board computer solutions and offer OEMs fast time-to-market with reduced development cost. Like integrated circuits, they provide OEMs with significant freedom in meeting form-fit-function requirements. For all these reasons the COM methodology has gained much popularity with OEMs in the embedded industry. COM Express® is an open industry standard for Computer-On-Modules. It is designed to be future proof and to provide a smooth transition path from legacy parallel interFaces to LVDS (Low Voltage Differential Signaling) interFaces. These include the PCI bus and parallel ATA on the one hand and PCI Express and Serial ATA on the other hand.
上传时间： 2013-11-05
上传用户：Wwill
The #1 Step-by-Step Guide to labviewNow Completely Updated for labview 8! Master labview 8 with the industry's friendliest, most intuitive tutorial: labview for Everyone, Third Edition. Top labview experts Jeffrey Travis and Jim Kring teach labview the easy way: through carefully explained, step-by-step examples that give you reusable code for your own projects! This brand-new Third Edition has been fully revamped and expanded to reflect new features and techniques introduced in labview 8. You'll find two new chapters, plus dozens of new topics, including Project Explorer, AutoTool, XML, event-driven programming, error handling, regular expressions, polymorphic VIs, timed structures, advanced reporting, and much more. Certified labview Developer (CLD) candidates will find callouts linking to key objectives on NI's newest exam, making this book a more valuable study tool than ever. Not just what to d why to do it! Use labview to build your own virtual workbench Master labview's foundations: wiring, creating, editing, and debugging VIs; using controls and indicators; working with data structures; and much more Learn the "art" and best practices of effective labview development NEW: Streamline development with labview Express VIs NEW: Acquire data with NI-DAQmx and the labview DAQmx VIs NEW: Discover design patterns for error handling, control structures, state machines, queued messaging, and more NEW: Create sophisticated user interFaces with tree and tab controls, drag and drop, subpanels, and more Whatever your application, whatever your role, whether you've used labview or not, labview for Everyone, Third Edition is the fastest, easiest way to get the results you're after!
上传时间： 2013-10-14
上传用户：shawvi
The LPC2292/2294 microcontrollers are based on a 16/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, together with 256 kB of embedded high-speed flash memory. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at the maximum clock rate. For critical code size applications, the alternative 16-bit Thumb mode reduces code by more than 30 pct with minimal performance penalty. With their 144-pin package, low power consumption, various 32-bit timers, 8-channel 10-bit ADC, 2/4 (LPC2294) advanced CAN channels, PWM channels and up to nine external interrupt pins these microcontrollers are particularly suitable for automotive and industrial control applications as well as medical systems and fault-tolerant maintenance buses. The number of available fast GPIOs ranges from 76 (with external memory) through 112 (single-chip). With a wide range of additional serial communications interFaces, they are also suited for communication gateways and protocol converters as well as many other general-purpose applications. Remark: Throughout the data sheet, the term LPC2292/2294 will apply to devices with and without the /00 or /01 suffix. The suffixes /00 and /01 will be used to differentiate from other devices only when necessary.
上传时间： 2014-12-30
上传用户：aysyzxzm
