The PW8205A8TS is the highest performance trench N-ch MOSFETs with extreme high cell density,which provide excellent RDSON and gate charge for most of the small power switching and loadswitch applications. The meet the RoHS and Product requirement with full function reliabilityapproved .
标签： 8205a8
上传时间： 2022-02-14
上传用户：wangshoupeng199
SCB10H series pressure elements are high performance absolute pressure sensors. The sensors are based on Murata's proven capacitive 3D-MEMS technology. They enable exceptional possibility for OEM customers to integrate pressure measurement function in an optimal way into their products. SCB10H series elements can be designed to match the application specific pressure range. It is a bare capacitive sensor element that enables optimized application specific package and electronics design.
标签： 传感器
上传时间： 2022-03-03
上传用户：
对某四轮独立驱动电动汽车轮毂电机进行研究,设计一种永磁无刷直流电机控制器.以STM32F103RBT6芯片为基础,对电机驱动电路、采样电路和保护电路分别进行硬件设计与分析;同时,采用模块化软件设计方案,对该控制器的软件系统进行升级.实验验证表明:所设计的电机控制器能使电机响应迅速、转速稳定、无超调,且电动车动力输出性能良好.A permanent magnet brushless direct current motor controller was designed by studying the hub motor of a four-wheel independent drive electric vehicle.Based on STM32 F103RBT6 chip,the hardware design and analysis of motor drive circuit,sampling circuit and protection circuit were carried out respectively.At the same time,modular software design scheme was adopted to upgrade the software system of the controller.Experimental results show that the designed motor controller can ensure the motor fast response,stable speed,no overshoot,and good power output performances.
上传时间： 2022-03-26
上传用户：qingfengchizhu
随着光伏发电系统快速发展,以及电动汽车充电桩的普及,传统的剩余电流保护器无法满足实际需求。介绍了一款B型剩余电流保护器,采用磁调制剩余电流互感器和零序电流互感器采集剩余电流。根据GB/T 22794—2017标准要求,可识别1 kHz及以下的正弦交流、带和不带直流分量的脉动直流、平滑直流等剩余电流信号。经信号调理电路将电压信号送到单片机进行采集和判断。通过试验测试,该样机在测试精度和速度上均符合国家标准的相关要求。The rapid development of photovoltaic power generation systems and the popularity of electric vehicle charging piles make the traditional residual current protective devices unable to meet the actual demand.This paper proposed a type B residual current protective device,which uses the magnetically modulated residual current transformer and the zero sequence current transformer to acquire the residual current.According to the requirements of GB/T 22794—2017,the type B residual current protective device can detect sinusoidal AC residual current of 1kHz and below 1kHz,pulsating DC residual current with and without DC component,smooth DC residual current and so on.The signal processing circuit sends the voltage signal to the MCU for acquisition and judgment.Through experimental tests,the device meets the relevant requirements of national standards in terms of test accuracy and speed.
标签： 电流保护器
上传时间： 2022-03-27
上传用户：
在半导体制冷技术的工作性能及其优缺点研究的基础上,设计了以单片机为核心控制元件,以TEC1-12706为执行元件的半导体制冷温度控制系统。采用高精度分段式PID控制算法配合PWM输出控制的方法实现温度控制;选择数字传感器DS18B20为温度检测元件,还包含1602液晶显示模块、按键调整输入模块和H桥驱动模块等。实际测试表明,该系统结构简单易行,操作方便,工作性能优良,同时针对该系统专门设计的温控算法,使半导体制冷器能更好地适应不同工况而充分发挥其制冷制热工作特性。Based on the study of the performance and advantages and disadvantages of thermoelectric cooler(TEC)technology,a thermoelectric cooling temperature control system with single-chip microcomputer as the core control element and TEC1-12706 as the executive element was designed. High precision piecewise PID control algorithm combined with PWM output control method is adopted to realize temperature control. The digital sensor DS18B20 is selected as the temperature detection element. It also includes 1602 LCD module,key adjustment input module and H bridge drive module. The actual test shows that the system has simple structure,convenient operation and excellent performance. Meanwhile,the temperature control algorithm specially designed for the system can make the semiconductor cooler better adapt to different working conditions and give full play to its refrigeration and heating characteristics.
上传时间： 2022-03-27
上传用户：
基于药物治疗在临床治疗中的重要性,分析目前服药提醒装置存在的不足,以STM32F103VET6单片机为控制核心,设计了一种多功能电子药箱。该系统包括显示模块、语音模块和数据存储模块。显示模块通过触摸屏电路和LED指示灯电路,与语音模块相配合,实现了服药提醒及指导的功能;数据存储模块通过EEPROM存储电路,能够实现掉电时服药信息不丢失的功能。并且为了实现电子药箱的智能化控制,开发了手机APP,两者之间可通过WIFI进行数据通信。经测试,该药箱能够有效地帮助慢性病患者按时、定量、正确服用药物,适合在家庭中推广使用,具有较高的应用价值和实践意义。Based on the importance of drug therapy in clinical treatment, this paper analyzes the shortcomings of current drug reminder devices, and designs a multi-function electronic medicine box with STM32 F103 VET6 microcontroller as the control core. The system includes a display module, a voice module, and a data storage module. The display module cooperates with the voice module through the touch screen circuit and the LED indicator circuit to realize the function of reminding and guiding the medicine;the data storage module can realize the function of not losing the medication information when the power is off through the EEPROM storage circuit.After testing, the medicine box can effectively help chronic diseases patients to take drugs on time, in a quantitative and correct manner,and is suitable for popularization in the family, and has high application value and practical significance.
标签： 电子药箱
上传时间： 2022-03-27
上传用户：
温度控制如今已成为当代社会研究的热点之一,而温度检测在现代设备参数检测中也是一项极其重要的技术,应用十分广泛。与传统的测温方法相比,红外测温方法具有时间短、精度高、使用简单方便等优点。本文以环境温度为被测对象,设计了以STC89C52单片机为控制中心的红外测温装置,能够实现对目标温度的实时采集、处理、显示和报警等功能。本设计主要是由STC89C52单片机、红外测温传感器、LCD1602液晶显示器、按键和蜂鸣器等部分组成,采用非接触的方式对目标温度进行实时检测。Temperature control has become one of the hotspots in contemporary social research,and temperature detection is an extremely important technology in modern equipment parameter detection.Compared with traditional method,the infrared temperature measuring method has advantages of short time,high precision and convenient operation,etc.This paper consider environment temperature as research objects and designs an infrared temperature measuring device which employs the STC89C52singlechipas-control center,and it can realize timely collection,processing,display and alarm function of the target temperature.The design is mainly composed of STC89C52 singlechip,infrared temperature sensor,LCD1602monitor,keys and buzzer,etc.This design detects the target temperature by non-contact method.
上传时间： 2022-03-27
上传用户：jiabin
CAN总线是汽车上应用最广泛的车载网络总线,具有实时性强、可靠性高、成本低等优点。鉴于此,介绍了一种利用飞思卡尔系列单片机MC9S12XS128作为控制器,利用其内部的MSCAN模块、CAN收发器TJA1040等外围元件进行CAN总线通信节点设计。该设计能够实现CAN总线数据的发送与接收,可应用于汽车及其他各种CAN总线通信系统。CAN bus is the most widely used on-board network bus in automobiles. It has the advantages of realtime, high reliability and low cost. In view of this,this paper introduces the design of CAN bus communication node by using Freescale MC9S12XS128 as controller,using its internal MSCAN module,CAN transceiver TJA1040 and other peripheral components. This design can realize the sending and receiving of CAN bus data,and can be used in automobile and other CAN bus communication systems.
上传时间： 2022-03-27
上传用户：
本设计介绍了一种基于STM32单片机控制的智能水杯,可利用插口式电源或无线充电底座为加热器提供能量,并在达到某种饮品所需温度时进行保温。水杯内置充电电池,可选用USB接口或无线充电。在水杯内部设置无线模块,用户利用手机App与水杯进行匹配进行加热操作,加热完后水杯会通过手机App和液晶显示屏实时反馈液体温度,通过指示灯显示电量情况等,给用户进行提醒。该智能水杯设计创新,实用价值较高。This paper introduces an intelligent water cup based by STM32 microcontroller,it can provide energy for the heater by socket type power supply or wireless charging base,and hold temperature needed for some kind of drink.Builtedin rechargeable battery,water cup can use USB or wireless charging.The wireless module is set up inside it,and customers can use mobile App to match and heat.After heating,water cup feeds back liquid temperature through the mobile App,and then displays on LCD,reminds users through the indicator light.The intelligent water cup is designed innovatively and has high practical value.
上传时间： 2022-03-28
上传用户：
文章提出了一种基于AT89S51单片机的智能家居系统的设计,该系统具有室内煤气以及烟雾的检测、家庭室内防盗等功能。文章详细分析了系统的总体设计,详尽分析并设计了煤气传感器模块、烟雾传感器模块、人体红外感应传感器模块、报警模块等各硬件部分,并利用PROTUES软件进行了系统仿真。仿真结果证明:系统具有成本低、效率高、操作方便等优点,达到了预期设计的效果。This paper presents the design of an intelligent home system based on AT89S51 microcontroller.The system has the functions of detecting indoor gas and smoke,guarding against theft in the home,and so on.The overall design of the system is analyzed in detail.The gas sensor module,smoke sensor module,human infrared sensor module,alarm module and other hardware parts are analyzed and designed in detail,and the system simulation is carried out using PROTUES software.The simulation results show that the system has the advantages of low cost,high efficiency,convenient operation and so on,and achieves the expected design effect.
上传时间： 2022-03-28
上传用户：
