A code that show the count back to a date determinate.
标签： determinate count code back
上传时间： 2013-12-20
上传用户：hasan2015
On-The-Go Supplement to the USB 2.0 Specification Revision 1.0
标签： Specification Supplement On-The-Go Revision
上传时间： 2017-09-27
上传用户：wangyi39
PICKIT™ 2 PROGRAMMER-TO-GO USER GUIDE The PICkit 2 Programmer-To-Go functionality allows a PIC MCU memory image to be downloaded into the PICkit 2 unit for later programming into a specific PIC MCU. No software or PC is required to program devices once the PICkit 2 unit is set up for Programming-To-Go. A USB power source for the PICkit 2 is all that is needed.
标签： PROGRAMMER-TO PICKIT 8482
上传时间： 2013-10-29
上传用户：ca05991270
The PCA9541 is a 2-to-1 I2C-bus master selector designed for high reliability dual masterI2C-bus applications where system operation is required, even when one master fails orthe controller card is removed for maintenance. The two masters (for example, primaryand back-up) are located on separate I2C-buses that connect to the same downstreamI2C-bus slave devices. I2C-bus commands are sent by either I2C-bus master and are usedto select one master at a time. Either master at any time can gain control of the slavedevices if the other master is disabled or removed from the system. The failed master isisolated from the system and will not affect communication between the on-line masterand the slave devices on the downstream I2C-bus.
上传时间： 2013-10-09
上传用户：3294322651
Internal Interrupts are used to respond to asynchronous requests from a certain part of themicrocontroller that needs to be serviced. Each peripheral in the TriCore as well as theBus Control Unit, the Debug Unit, the Peripheral Control Processor (PCP) and the CPUitself can generate an Interrupt Request.So what is an external Interrupt?An external Interrupt is something alike as the internal Interrupt. The difference is that anexternal Interrupt request is caused by an external event. Normally this would be a pulseon Port0 or Port1, but it can be even a signal from the input buffer of the SSC, indicatingthat a service is requested.The User’s Manual does not explain this aspect in detail so this ApNote will explain themost common form of an external Interrupt request. This ApNote will show that there is aneasy way to react on a pulse on Port0 or Port1 and to create with this impulse an InterruptService Request. Later in the second part of the document, you can find hints on how todebounce impulses to enable the use of a simple switch as the input device.Note: You will find additional information on how to setup the Interrupt System in theApNote “First steps through the TriCore Interrupt System” (AP3222xx)1. It would gobeyond the scope of this document to explain this here, but you will find selfexplanatoryexamples later on.
上传时间： 2013-10-27
上传用户：zhangyigenius
The PL2303 USB to Serial adapter is your smart and convenient accessory forconnecting RS-232 serial devices to your USB-equipped Windows host computer. Itprovides a bridge connection with a standard DB 9-pin male serial port connector inone end and a standard Type-A USB plug connector on the other end. You simplyattach the serial device onto the serial port of the cable and plug the USB connectorinto your PC USB port. It allows a simple and easy way of adding serial connectionsto your PC without having to go thru inserting a serial card and traditional portconfiguration.This USB to Serial adapter is ideal for connecting modems, cellular phones, PDAs,digital cameras, card readers and other serial devices to your computer. It providesserial connections up to 1Mbps of data transfer rate. And since USB does not requireany IRQ resource, more devices can be attached to the system without the previoushassles of device and resource conflicts.Finally, the PL-2303 USB to Serial adapter is a fully USB Specification compliantdevice and therefore supports advanced power management such as suspend andresume operations as well as remote wakeup. The PL-2303 USB Serial cable adapteris designed to work on all Windows operating systems.
上传时间： 2013-11-01
上传用户：ghostparker
Abstract: This article explains the recent trend in heart-rate and fitness monitors to go wireless toeliminate cables to allow free movement, and allow convenient data collection without the need to plug intheir devices. It details a typical wireless system, using the MAX1472 crystal-referenced phase-lockedloop (PLL) VHF/UHF transmitter.
标签： Heart-RateFitness Monitors Wireless Go
上传时间： 2013-11-11
上传用户：xiaowei314
CHM decompiler is a program that converts the internal files of CHM files back into the HHP, HHC, and HHK, etc. used to compile the documentation. CHM decompiler是一个把CHM 文件的内部文件转换成 HHP, HHC,和HHK等的程序。它用于编译文件。
标签： files decompiler CHM the
上传时间： 2015-01-10
上传用户：myworkpost
This Unix C code monitors a web server every few minutes by trying to retrieve its home page. It sends you email when it can t connect, and every so often while the server is still down. It sends a final message when it comes back up. If you have email paging, just direct the email to your pager address.
标签： monitors retrieve minutes server
上传时间： 2015-01-11
上传用户：pompey
Library of C functions that allows a program to use WinSock 2 functionality if it is available or fall back to WinSock 1.1 if it isn t.
标签： functionality functions available Library
上传时间： 2015-01-18
上传用户：LIKE
