Abstract: A laser module designer can use a fixed resistor, mechanical pot, digital pot, or a digital-to-analogconverter (DAC) to control the laser driver's modulation and bias currents. The advantages of a programmablemethod (POT or DAC) are that the manufacturing process can be automated and digital control can be applied(e.g., to compensate for temperature). Using POTs can be a more simple approach than a DAC. There can be aslight cost advantage to using a POT, but this is usually not significant relative to other pieces of the design.Using a DAC can offer advantages, including improved linearity (translating to ease of software implementationand ability to hit the required accuracy), increased board density, a wider range of resolutions, a betteroptimization range, ease of use with a negative voltage laser driver, and unit-to-unit consistency
上传时间: 2013-11-13
上传用户:ca05991270
Abstract: IC switches and multiplexers are proliferating, thanks to near-continual progress in lowering the supply voltage,incorporating fault-protected inputs, clamping the output voltage, and reducing the switch resistances. The latest of these advancesis the inclusion of precision resistors to allow two-point calibration of gain and offset in precision data-acquisition systems.
上传时间: 2013-11-12
上传用户:acwme
The purpose of this application note is to show an example of how a digital potentiometer can be used in thefeedback loop of a step-up DC-DC converter to provide calibration and/or adjustment of the output voltage.The example circuit uses a MAX5025 step-up DC-DC converter (capable of generating up to 36V,120mWmax) in conjunction with a DS1845, 256 position, NV digital potentiometer. For this example, the desiredoutput voltage is 32V, which is generated from an input supply of 5V. The output voltage can be adjusted in35mV increments (near 32V) and span a range wide enough to account for resistance, potentiometer and DCDCconverter tolerances (27.6V to 36.7V).
上传时间: 2014-12-23
上传用户:781354052
BP8Y系列频敏变阻器(以下简称变阻器)专用于电机功率1.5~200kW,频率为50Hz的YZR系列起重及冶金用三相异步电动机频繁操作条件下的起动及反接设备。该变阻器直接连接于异步电动机的转子回路中, 不需另装接触器等短接设备;能使电动机获得接近恒转矩的机械特性,是极为理想的起动元件。
上传时间: 2013-11-04
上传用户:guojin_0704
转换器是指将一种信号转换成另一种信号的装置。信号是信息存在的形式或载体。在自动化仪表设备和自动控制系统中,常将一种信号转换成另一种与标准量或参考量比较后的信号,以便将两类仪表联接起来,因此,转换器常常是两个仪表(或装置)间的中间环节。
上传时间: 2013-11-18
上传用户:a3318966
为了对中频PCM信号进行直接解调,提出一种全新的数字化PCM中频解调器的设计方法。在实现过程中,采用大规模的FPGA芯片对位帧同步器进行了融合,便于设备的集成化和小型化。这种新型的中频解调器比传统的基带解调器具有硬件成本低和误码率低等优点。
上传时间: 2013-12-20
上传用户:jiangxiansheng
看门狗是一个计数器,它需要在一定的看门狗延时周期内被清零,如果没有清零动作,看门狗电路将产生一个复位信号使系统重新启动或建立一个非屏蔽终端、执行故障恢复子程序。
上传时间: 2013-10-30
上传用户:曹云鹏
基于数字微镜器件(Digital Micro-mirror Device,DMD)的哈达玛变换光谱技术是一种新型的光谱成像技术,在国内很少有专门的文献介绍[1-3]。文中先介绍了本实验采用的哈达玛光谱仪样机的原理以及哈达玛成像光谱仪优于传统模板的独特之处,即获得多通道高能量高信噪比的光谱数据,然后描述对采集到的数据做高信噪比,高分辨率压缩处理,最后说明此方法实时性强、图像失真小、实用价值高、应用范围广。
上传时间: 2013-11-25
上传用户:eastimage
BP8R3系列频敏变阻器(以下简称变阻器)适用于电机功率22~2240kW,频率为50Hz的绕线型三相异步电动机不频繁操作条件下的偶尔短时起动。
上传时间: 2013-10-08
上传用户:togetsomething
以双音多频信号为例,通过运用快速傅里叶变换和Hanning窗等数学方法,分析了信号频率,电平和相位之间的关系,推导出了计算非整周期正弦波形信噪比的算法,解决了数字信号处理中非整周期正弦波形信噪比计算精度低下的问题。以C编程语言进行实验,证明了算法的正确性和可重用性,并可极大的提高工作效率。
上传时间: 2014-01-18
上传用户:laomv123