ABSTRACTThe flyback power stage is a popular choice for single and multiple output dc-to-dc converters at powerlevels of 150 Watts or less. Without the output inductor required in buck derived topologies, such as theforward or push-pull converter, the component count and cost are reduced. This application note will reviewthe design procedure for the power stage and control electronics of a flyback converter. In these isolatedconverters, the error signal from the secondary still needs to cross the isolation boundary to achieveregulation. By using the UC3965 Precision Reference with Low Offset Error Amplifier on the secondaryside to drive an optocoupler and the UCC3809 Economy Primary Side Controller on the primary side, asimple and low cost 50 Watt isolated power supply is realized.
标签： 隔离
上传时间： 2021-11-24
上传用户：kingwide
This Section covers the design of power transformers used in buck-derived topologies: forward converter, bridge, half-bridge, and full-wave centertap. Flyback transformers (actually coupled inductors) are covered in a later Section. For more specialized applications, the principles discussed herein will generally apply.
上传时间： 2021-12-16
上传用户：fliang
以STC12C5A60S2单片机为控制核心,采用2.4G(JF24D)无线遥控模块进行无线发射与接收,设计了一种双电机遥控船模控制系统.该系统通过切换档杆实现前进后退,方向盘左右转动、暂停按钮等控制直流电机的正转、反转、暂停,使得电机驱动的遥控船模实现前进后退、左右转向、暂停等功能,有效解决了驱动功率小和船模之间相互干扰等问题,可广泛应用于遥控船模领域.Using STC12C5A60S2 single-chip microcomputer as the controller and 2.4 G(JF24D)wireless remote control module for wireless transmission and reception, a dual-motor remote control ship model control system is designed. The system realizes forward and backward by switching the gear lever. The steering wheel rotates left and right and the pause button controls the forward, reverse and pause of the dc motor. The remote controller of ship model driven by the motor realizes forward and backward, left and right steering, pause and other functions. The ship model control system can effectively solve the problems of small driving power and mutual interference between ship models, and can be widely used in the field of remote controller of ship model.
上传时间： 2022-03-27
上传用户：
设计功率MOSFET驱动电路时需重点考虑寄生参数对电路的影响。米勒电容作为MOSFET器件的一项重要参数,在驱动电路的设计时需要重点关注。重点观察了MOSFET的开通和关断过程中栅极电压、漏源极电压和漏源极电流的变化过程,并分析了米勒电容、寄生电感等寄生参数对漏源极电压和漏源极电流的影响。分析了栅极电压在米勒平台附近产生振荡的原因,并提出了抑制措施,对功率MOSFET的驱动设计具有一定的指导意义。When designing the drive circuit of power MOSFET,the influence of parasitic parameters on the circuit should be concerned.As an important parameter of MOSFET device,Miller capacitance should be considered in the design of drive circuit.The variation of gate voltage,drain source voltage and drain source current during the turn-on and turn-off of MOSFET were observed.The influences of parasitic parameters such as Miller capacitance and parasitic inductance on drain source voltage and drain source current were analyzed.The reasons of gate voltage oscillation nearby Miller plateau were analyzed,and the restraining measures were put forward.This research was instructive for the drive design of power MOSFET.
标签： mosfet
上传时间： 2022-04-02
上传用户：默默
以单片机控制A/D转换器TLC549为例,对A/D转换器的主要技术指标进行了分析研究,在Proteus平台下,完成了A/D转换电路的构建,采用器件工作时序方式进行程序编写,借助仿真图表、虚拟仪器等工具对A/D转换的数据进行测量并对失调误差、增益误差、微分非线性、积分非线性和转换时间等重要参数进行了详细分析。结果表明:使用Proteus软件可对A/D转换过程进行定性分析,将抽象的A/D转换器技术指标直观化、形象化展现出来,有助于学生更好地理解A/D转换过程。The main technical indicators of A/D converter were analyzed and studied with an example from A/D converter TLC2543 which is controlled by using SCM.It was completed the construction of the A/D converter circuit under the Proteus software.The programming based on the operation sequence of the chip is put forward.With the aid of the simulation tools such as virtual instrument,simulation charts provided by Proteus,the important parameters of circuit such as offset error,gain error,differential nonlinearity(DNL),integral nonlinearity (INL) and conversion time are analyzed detailedly.Simulation results show that the A/D conversion process can be qualitatively analyzed and visualized the abstract indicators of A/D.The system can help students better to understand the SCM conversion process.
上传时间： 2022-04-04
上传用户：
抢答器是一种智力竞赛常用的器件,抢答器的设计方法千差万别,文章利用常用的数字电子器件,设计了八路抢答器电路的设计、仿真及实现的全过程,提出两种可行的设计方案:方案1采用74ls373实现电路锁存,74ls148实现电路编码,74ls74及数码管实现电路显示;方案二采用CD4511BCN和LMC555CM集成电路及数码管实现抢答器的控制和显示。本文设计用的器件简单,容易理解,适用于初学电子技术的人员。Answer scrambler is a common device in intelligence competition, and its design methods vary greatly. This paper designs the whole process of design, simulation and Realization of the circuit of eight-way answer scrambler by using common digital electronic devices, and puts forward two feasible design schemes: scheme 1 uses 74 ls373 to realize circuit latching, 74 ls148 to realize circuit coding,74 ls74 and digital tube to realize circuit. The second scheme uses CD4511 BCN, LMC555 CM integrated circuit and digital tube to control and display the answerer. The device designed in this paper is simple and easy to understand, and it is suitable for the beginners of electronic technology.
标签： 抢答器
上传时间： 2022-04-05
上传用户：
le flows through MOS channel while Ih flows across PNP transistor Ih= a/(1-a) le, IE-le+lh=1/(1-a)' le Since IGBT has a long base PNP, a is mainly determined by ar si0 2ar= 1/cosh(1/La), La: ambipolar diff length a-0.5 (typical value)p MOSFET channel current (saturation), le=U"Cox"W(2"Lch)"(Vc-Vth)le Thus, saturated collector current Ic, sat=1/(1-a)"le=-1/(1-a)"UCox"W/(2Lch)"(Vo-Vth)2Also, transconductance gm, gm= 1/(1-a)"u' Cox W/Lch*(Vo-Vth)Turn-On1. Inversion layer is formed when Vge>Vth2. Apply positive collector bias, +Vce3. Electrons flow from N+ emitter to N-drift layer providing the base current for the PNP transistor4. Since J1 is forward blased, hole carriers are injected from the collector (acts as an emitter).5. Injected hole carriers exceed the doping level of N-drift region (conductivity modulation). Turn-Off1. Remove gate bias (discharge gate)2. Cut off electron current (base current, le, of pnp transistor)
标签： igbt
上传时间： 2022-06-20
上传用户：wangshoupeng199
3-phase Sensor-less Fan Motor DriverAM2355NThe AM2355N is a 3-phase sensor-less DC fan motor driver IC. It senses the BEMF (BackElectro-Motive Force) of the motor in rotation and provides corresponding commutation current tothe motor. Rotation speed can be controlled by PWM input signal. The drivers include LockDetection, Thermal Shutdown, and Over-current Protection. Forward and Reverse control.www.junmintech.com
标签： am2355n
上传时间： 2022-07-26
上传用户：
