虫虫首页| 资源下载| 资源专辑| 精品软件
登录| 注册

experimental

  • 高精度双向DC电源电流采样电路设计

    为适应双向DC/DC功率变换的电流采样需求,一种高精度高边电流采样电路被提出。其基本思想是在功率电路的高边串入采样电阻,借助电流镜原理并引入偏置电流电路,将双向电流均转换为正向电压输出。通过理论分析与仿真结合的方法对电流镜采样原理及4种不同的偏置电流电路方案进行对比,最后通过实验数据验证了高精度高边电流采样电路的有效性。实验数据表明,该采样电路可在-25~75℃的温度工作范围内,针对-10~+10 A范围内的电流采样实现优于5%的采样精度。Current sensing plays an important role in controlling,monitoring or protection functions of power systems.To meet the current sensing requirement of bidirectional DC/DC converters,a high-accuracy bidirectional current sensing circuit is proposed.The proposed current sensing circuit inserts a resistor in the path of the current to be sensed,while the current mirror and biased current circuit are introduced.Therefore,the bidirectional current can be expressed by positive voltage.By theoretical analysis and simulation,the sampling theory is analyzed and four biased current circuits are compared.At last,experimental results verified the proposed method.It is demonstrated that the proposed current sensing circuit can achi...

    标签: 双向DC电源 电流采样

    上传时间: 2022-04-22

    上传用户:

  • 基于无迹卡尔曼滤波算法的锂电池SOC估计

    应用无迹卡尔曼滤波算法(UKF)进行锂电池的SOC估计,采用Thevenin二阶RC等效电路模型,对HPPC电池脉冲充放电实验数据进行Matlab处理,得到较为准确的模型.通过在Matlab中编写算法程序,对不同工况的估计值与实际值进行误差估算及对比分析,通过此算法进行SOC估计,得到该算法可有效降低系统误差并纠正SOC的初值偏差.The non trace Calman filter (UKF) is applied to the SOC estimation of lithium battery. The Thevenin two order RC equivalent circuit model is used to process the HPPC battery pulse charge discharge experimental data by Matlab processing, and a more accurate model is obtained. By writing algorithm program in Matlab, the error estimation and comparison analysis of the estimated value and actual value of different states are carried out, and the SOC estimation is carried out by this algorithm. The algorithm can effectively reduce the system error and correct the initial value deviation of the SOC.

    标签: 卡尔曼滤波

    上传时间: 2022-05-03

    上传用户:默默

  • 基于DSP28335+IR2110芯片的移相全桥驱动电路设计

    为解决移相全桥电路驱动及相角控制问题,设计了一种数字控制的移相全桥驱动电路.以TPL521为光耦隔离、IR2110为栅极驱动芯片.由DSP产生PWM信号,经过光耦隔离和逻辑电路后送至IR2110进行相角控制.文章对IR2110驱动电路原理进行分析及参数进行设计,对TMS320F28335进行设置并给出部分代码.实验结果表明:通过TMS320F28335可产生的不同相角的PWM波形,满足了移相全桥对不同相角控制的要求.In order to solve the problem of phase-shifted full-bridge circuit driving and phase angle control,a digitally controlled phaseshifted full-bridge driving circuit was designed. TPL521 optocoupler isolation,IR2110 gate driver chip. PWM signals are generated by the DSP and sent to the IR2110 for phase angle control after optocoupler isolation and logic circuits. This text carries on the analysis to the principle of IR2110 drive circuit and parameter design,set up and give out some code to TMS320F28335. The experimental results show that the PWM waveforms with different phase angles generated by TMS320F28335 can meet the requirements of phase-shifted full-bridge control for different phase angles.

    标签: dsp28335 ir2110 芯片

    上传时间: 2022-05-03

    上传用户:zhanglei193

  • 基于PSIM仿真的开关电源Boost电路的设计

    基于PSIM仿真软件,分析了Boost电路拓扑结构,设定了参数要求进行电路仿真设计,通过电路仿真软件PSIM对Boost电路工作在CCM模式下,合理设置占空比参数。实验结果表明理论分析与仿真的一致性和参数设计的正确性,输出电压和电流参数稳定,Boost电路输出效率高。This design is based on PSIM simulation software,analyzes the topology of Boost circuit,sets the parameter re- quirements for circuit simulation design,and reasonably sets the duty cycle parameters for Boost circuit working in CCM mode through PSIM simulation software.The experimental results show that the theoretical analysis and simulation are consis- tent and the parameter design is correct,the output voltage and current parameters are stable.

    标签: psim 开关电源 boost

    上传时间: 2022-05-04

    上传用户: