Wi-Fi pollution, or an excessive number of access points in the area, especially on the same or neighboring channel, can prevent access and interfere with the use of other access points by others, caused by overlapping channels in the 802.11g/b spectrum
标签： especially pollution excessive the
上传时间： 2017-07-29
上传用户：我们的船长
The C500 microcontroller family usually provides only one on-chip synchronous serialchannel (SSC). If a second SSC is required, an emulation of the missing interface mayhelp to avoid an external hardware solution with additional electronic components.The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using optimized SW routines with a performance up to 25KBaud in Slave Mode with half duplex transmission and an overhead less than 60% atSAB C513 with 12 MHz. Due to the implementation in C this performance is not the limitof the chip. A pure implementation in assembler will result in a strong reduction of theCPU load and therefore increase the maximum speed of the interface. In addition,microcontrollers like the SAB C505 will speed up the interface by a factor of two becauseof an optimized architecture compared with the SAB C513.Moreover, this solution lays stress on using as few on-chip hardware resources aspossible. A more excessive consumption of those resources will result in a highermaximum speed of the emulated interface.Due to the restricted performance of an 8 bit microcontroller a pin compatible solution isprovided only; the internal register based programming interface is replaced by a set ofsubroutine calls.The attached source files also contain a test shell, which demonstrates how to exchangeinformation between an on-chip HW-SSC and the emulated SW-SSC via 5 external wiresin different operation modes. It is based on the SAB C513 (Siemens 8 bit microcontroller).A table with load measurements is presented to give an indication for the fraction of CPUperformance required by software for emulating the SSC.
标签： synchronous Emulating serial
上传时间： 2014-01-31
上传用户：z1191176801
The SP2526A device is a dual +3.0V to +5.5V USB Supervisory Power Control Switch ideal for self-powered and bus-powered Universal Serial Bus (USB) applications. Each switch has low on-resistance (110mΩ typical) and can supply 500mA minimum. The fault currents are limited to 1.0A typical and the flag output pin for each switch is available to indicate fault conditions to the USB controller. The thermal shutdown feature will prevent damage to the device when subjected to excessive current loads. The undervoltage lockout feature will ensure that the device will remain off unless there is a valid input voltage present.
标签： High-Side Switch Power Dual USB
上传时间： 2019-03-06
上传用户：bhitr
The AZ1117 is a series of low dropout three-terminal regulators with a dropout of 1.15V at 1A output current. The AZ1117 series provides current limiting and thermal shutdown. Its circuit includes a trimmed bandgap reference to assure output voltage accuracy to be within 1% for 1.5V, 1.8V, 2.5V, 2.85V, 3.3V, 5.0V and adjustable versions or 2% for 1.2V version. Current limit is trimmed to ensure specified output current and controlled short-circuit current. On-chip thermal shutdown provides protection against any combination of overload and ambient temperature that would create excessive junction temperature. The AZ1117 has an adjustable version, that can provide the output voltage from 1.25V to 12V with only 2 external resistors.
上传时间： 2019-04-11
上传用户：heaven0o0o0
The PW4554 is a cost-effective, fully integrated high input voltage single-cell Li-ion battery charger.The charger uses a CC/CV charge profile required by Li-ion battery. The charger accepts an inputvoltage up to 24V but is disabled when the input voltage exceeds the OVP threshold, typically 6.8V,to prevent excessive power dissipation. The 24V rating eliminates the over-voltage protection circuitrequired in a low input voltage charger
标签： pw4554
上传时间： 2022-02-11
上传用户：
为了确保最佳性能，请仔细阅读本手册。请将其保存在安全的地方，以备将来参考。将本机安装在阴凉，干燥，清洁的地方-远离窗户的热源，过多的振动灰尘，湿气和冷源。避免嗡嗡声的变压器，电动机。为避免起火或电击，请勿使本机遭受雨淋或浸水。绝对不要机柜。如果有东西掉入设备中，请与经销商联系。不要在开关，控件或连接线上用力。移动设备时，请先拔下电源插头和与其他设备相连的电线。切勿自己拉电线。机柜上的开口可确保设备正常通风。如果这些开口被阻塞，则机柜内部的温度将迅速升高。因此，请避免将物品放在这些开口处，并将其安装在后方10厘米，两侧20厘米，深30厘米9通风条件确保设备的顶部面板至少留出一定空间。否则不仅会损坏设备，还会引起火灾。To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference Install this unit in a cool, dry, clean place -away from windows heat sources, sources of excessive vibration dust, moisture and cold. Avoid sources of humming transformers, motors). To prevent fire or electrical shock do not expose the unit to rain or water.
上传时间： 2022-04-02
上传用户：
