Features • Compatible with MCS-51® Products • 8K Bytes of In-System Programmable (ISP) Flash Memory – Endurance: 1000 Write/erase Cycles • 4.0V to 5.5V Operating Range • Fully Static Operation: 0 Hz to 33 MHz • Three-level Program Memory Lock • 256 x 8-bit Internal RAM • 32 Programmable I/O Lines • Three 16-bit Timer/Counters • Eight Interrupt Sources • Full Duplex UART Serial Channel • Low-power Idle and Power-down Modes • Interrupt Recovery from Power-down Mode • Watchdog Timer • Dual Data Pointer • Power-off Flag
标签： 8226 Programmable Compatible In-System
上传时间： 2015-06-27
上传用户：dianxin61
Nand Flash Translation Layer 用于nandflash的操作。 bad block memory map garbage collection average erase
标签： Translation collection nandflash average
上传时间： 2014-07-02
上传用户：lingzhichao
/* Check_SST_39VF400A Check manufacturer and device ID /* CFI_Query CFI Query Entry/Exit command sequence /* erase_One_Sector erase a sector of 2048 words /* erase_One_Block erase a block of 32K words /* erase_Entire_Chip erase the contents of the entire chip /* Program_One_Word Alter data in one word /* Program_One_Sector Alter data in 2048 word sector /* Program_One_Block Alter data in 32K word block
标签： manufacturer Check_SST CFI_Query command
上传时间： 2013-12-15
上传用户：jjj0202
第一版YL2410开发板的BIOS 功能比较简单，上电之后，LCD显示蓝色、绿色、红色三个竖条 同时串口显示如下： Power on reset ************************************ * * * YL2410 Board BIOS V2006 * * Http://www.ucdragon.com * * * ************************************ NAND Flash Boot Please select function : 0 : USB download file（通过USB下载文件） 1 : Uart download file（通过串口下载文件） 2 : Write Nand flash with download file（将下载的文件烧写到NandFlash） 3 : Load Pragram from Nand flash and run（从NandFlash装载文件并运行） 4 : erase Nand flash regions（擦除NandFlash区域） 5 : Write NOR flash with download file（将下载的文件烧写到NorFlash） 6 : Set boot params（设置Linux启动相关参数） 7 : Set AutoBoot parameter,1:linux 2:wince(设置WINCE自启动）
上传时间： 2015-09-15
上传用户：Amygdala
The goal of this library is to make ODBC recordsets look just like an STL container. As a user, you can move through our containers using standard STL iterators and if you insert(), erase() or replace() records in our containers changes can be automatically committed to the database for you. The library s compliance with the STL iterator and container standards means you can plug our abstractions into a wide variety of STL algorithms for data storage, searching and manipulation. In addition, the C++ reflection mechanism used by our library to bind to database tables allows us to add generic indexing and lookup properties to our containers with no special code required from the end-user. Because our code takes full advantage of the template mechanism, it adds minimal overhead compared with using raw ODBC calls to access a database.
标签： recordsets container library ODBC
上传时间： 2015-10-11
上传用户：xlcky
This leon3 design is tailored to the Altera NiosII Startix2 Development board, with 16-bit DDR SDRAM and 2 Mbyte of SSRAM. As of this time, the DDR interface only works up to 120 MHz. At 130, DDR data can be read but not written. NOTE: the test bench cannot be simulated with DDR enabled because the Altera pads do not have the correct delay models. * How to program the flash prom with a FPGA programming file 1. Create a hex file of the programming file with Quartus. 2. Convert it to srecord and adjust the load address: objcopy --adjust-vma=0x800000 output_file.hexout -O srec fpga.srec 3. Program the flash memory using grmon: flash erase 0x800000 0xb00000 flash load fpga.srec
标签： Development Startix2 tailored Altera
上传时间： 2014-01-19
上传用户：chongcongying
FLASH文件系统的源码，Flash memory is a nonvolatile memory, which allows the user to electrically program (write) and erase information. The exponential growth of flash memory has made this technology an indispensable part of hundreds of millions of electronic devices. Flash memory has several significant differences with volatile (RAM) memory and hard drive technologies which requires unique software drivers and file systems. This paper provides an overview of file systems for flash memory and focuses on the unique software requirements of flash memory devices.
上传时间： 2015-11-29
上传用户：问题问题
NAND Flash Boot Please select function : 0 : USB download file（通过USB下载文件） 1 : Uart download file（通过串口下载文件） 2 : Write Nand flash with download file（将下载的文件烧写到NandFlash） 3 : Load Pragram from Nand flash and run（从NandFlash装载文件并运行） 4 : erase Nand flash regions（擦除NandFlash区域） 5 : Write NOR flash with download file（将下载的文件烧写到NorFlash） 6 : Set boot params（设置Linux启动相关参数） 7 : Set AutoBoot parameter,1:linux 2:wince(设置WINCE自启动）
标签： download USB function Please
上传时间： 2016-02-15
上传用户：s363994250
Making a cheap 1M SPI Rom Emulator 8 second to copy from parallel to SPI re-Program STM Serial Flash M25P10 by reading 29010 parallel ROM Running on standard 8051 32 I/O, a TTL 7407 as bus switch. Total programming time is about 8 seconds including erase, Program
标签： re-Program SPI Emulator parallel
上传时间： 2016-03-22
上传用户：wanqunsheng
Name Function --- --- --- --- --- --- Check_SST_39VF160 Check manufacturer and device ID CFI_Query CFI Query Entry/Exit command sequence erase_Entire_Chip erase the contents of the entire chip erase_One_Sector erase a sector of 2048 word erase_One_Block erase a block of 32K word Program_One_Word Alter data in one word Program_One_Sector Alter data in 2048 word sector Program_One_Block Alter data in 32K word block Check_Toggle_Ready End of internal program or erase detection using Toggle bit Check_Data_Polling End of internal program or erase detection using Data# polling
标签： manufacturer Check_SST Function CFI_Que
上传时间： 2013-12-21
上传用户：徐孺
