Agilent 34401A Service Guide.pdfIEC Measurement Category II includes electrical devices connected to mains at an outlet on a branch circuit. Such devices include most small appliances, test equipment, and other devices that plug into a branch outlet or socket. The 34401A may be used to make measurements with the HI and LO inputs connected to mains in such devices, or to the branch outlet itself (up to 300 VAC). However, the 34401A may not be used with its HI and LO inputs connected to mains in permanently installed electrical devices such as the main circuit-breaker panel, sub-panel disconnect boxes, or permanently wired motors. Such devices and circuits are subject to overvoltages that may exceed the protection limits of the 34401A. Note: Voltages above 300 VAC may be measured only in circuits that are isolated from mains. However, transient overvoltages are also present on circuits that are isolated from mains. The Agilent 34401A are designed to safely withstand occasional transient overvoltages up to 2500 Vpk. Do not use this equipment to measure circuits where transient overvoltages could exceed this level. Additional Notices Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC This product complies with the WEEE Directive (2002/96/EC) marking requirement. The affixed product label (see below) indicates that you must not discard this electrical/electronic product in domestic household waste. Product Category: With reference to the equipment types in the WEEE directive Annex 1, this product is classified as a "Monitoring and Control instrumentation" product. Do not dispose in domestic household waste. To return unwanted products, contact your local Agilent office, or see www.agilent.com/environment/product for more information. Agilent 34138A Test Lead Set The Agilent 34401A is compatible with the Agilent 34138A Test Lead Set described below. Test Lead Ratings Test Leads - 1000V, 15A Fine Tip Probe Attachments - 300V, 3A Mini Grabber Attachment - 300V, 3A SMT Grabber Attachments - 300V, 3A Operation The Fine Tip, Mini Grabber, and SMT Grabber attachments plug onto the probe end of the Test Leads. Maintenance If any portion of the Test Lead Set is worn or damaged, do not use. Replace with a new Agilent 3413
标签： agilent
上传时间： 2022-02-20
上传用户：
电子书-RTL Design Style Guide for Verilog HDL540页A FF having a fixed input value is generated from the description in the upper portion of Example 2-21. In this case, ’0’ is output when the reset signal is asynchronously input, and ’1’ is output when the START signal rises. Therefore, the FF data input is fixed at the power supply, since the typical value ’1’ is output following the rise of the START signal. When FF input values are fixed, the fixed inputs become untestable and the fault detection rate drops. When implementing a scan design and converting to a scan FF, the scan may not be executed properl not be executed properly, so such descriptions , so such descriptions are not are not recommended. recommended.[1] As in the lower part of Example 2-21, be sure to construct a synchronous type of circuit and ensure that the clock signal is input to the clock pin of the FF. Other than the sample shown in Example 2-21, there are situations where for certain control signals, those that had been switched due to the conditions of an external input will no longer need to be switched, leaving only a FF. If logic exists in a lower level and a fixed value is input from an upper level, the input value of the FF may also end up being fixed as the result of optimization with logic synthesis tools. In a situation like this, while perhaps difficult to completely eliminate, the problem should be avoided as much as possible.
标签： RTL verilog hdl
上传时间： 2022-03-21
上传用户：canderile
电学中的测量技术涉及范围非常广,电流测量在电学计量中占有非常重要的位置。如何精确地进行电流测量是精密测量的一大难题。传统的电流检测电路多采用运算放大芯片与片外电流检测电路相结合的方式,电路集成度很低,需要较多的接口和资源才能完成对电路的检测。本文把所有电路部分都集成在一块芯片上,包括检测电阻,运算放大器电路及模拟转数字转换电路,从而在电路内部可以进行电流检测,使电路更好的集成化。前置电路使用二级共源共栅结构的运算放大器,减小沟道长度调制效应造成的电流误差。10位SAR ADC中采用电容驱动能力强的传输门保证了模数转化器的有效精度。比较器模块采用再生锁存器与迟滞比较器作为基础单元组合解决精密测量的问题。本设计可以作为嵌入芯片内的一小部分而检测芯片中的微小电流1mA~100mA,工作电压在1.8v左右,电流检测精度预期达到10uA的需求。The measurement technology in electricity involves a wide range,and current measurement plays a very important position in electrical measurement.How to accurately measure current is a big problem in precision measurement. The traditional current detecting circuit adopts the combination of the operational amplifier chip and theoff-chip current detecting circuit, The circuit integration is very low, and more interfaces and resources are needed tocomplete the circuit detection.This topic integrates all the circuit parts into one chip, including detection resistance, operational amplifier circuit andanalog to digital conversion circuit. Highly integrated circuit makes the external resources on the chip more intensive,so that current detection can be carried out inside the circuit, so that the circuit can be better integrated. Thefront-end circuit of this project uses two-stage cascade operational amplifier and cascade tube to reduce the currenterror caused by channel length modulation effect. In 10-bit SAR ADC, the transmission gate with strong capacitivedriving ability ensures the effective accuracy of the analog-to-digital converter. Comparator module uses regenerativelatch and hysteresis comparator as basic unit to solve the difficult problem of precision measurement. This topic can beused as a small part of the embedded chip to detect the micro-current in the chip 1 mA~100 mA, the working voltageis about 1.8v, and the current detection accuracy is expected to reach the requirement of 10 uA.
上传时间： 2022-04-03
上传用户：
S32K1xx Series Reference Manual 用户手册--2029页 Supports S32K116, S32K118, S32K142, S32K144, S32K146, and S32K148S32K是一款符合AEC-Q100规范、基于32位ARM Cortex-M4F和Cortex-M0+内核的MCU，适用于通用汽车和高可靠性工业应用。The S32K1xx product series further extends the highly scalable portfolio of Arm® Cortex®-M0+/M4F MCUs in the automotive industry. It builds on the legacy of the KEA series, while introducing higher memory options alongside a richer peripheral set extending capability into a variety of automotive applications. With a 2.70–5.5 V supply and focus on automotive environment robustness, the S32K product series devices are well suited to a wide range of applications in electrically harsh environments, and are optimized for cost-sensitive applications offering low pin-count options. The S32K product series offers a broad range of memory, peripherals, and package options. It shares common peripherals and pin counts, allowing developers to migrate easily within an MCU family or among the MCU families to take advantage of more memory or feature integration. This scalability allows developers to use the S32K product series as the standard for their end product platforms, maximizing hardware and software reuse and reducing time to market
标签： S32K116 S32K118 S32K142 S32K144
上传时间： 2022-04-16
上传用户：jason_vip1
为了提高超高频RFID系统中阅读器在低信噪比的情况下仍具有较高的识别能力,提出一种基于FPGA系统结合软件无线电方法实现超高频RFID射频前端电路方案。超高频射频识别系统必须符合EPC Class 1generation 2标准,所设计的电路系统以Xilinx公司的XC6SLX16-2CSG324FPGA芯片为硬件基础,将数字基带调制解调和中频滤波电路在FPGA系统中设计实现,重点阐述了射频前端电路的设计结构、AD/DA转换电路,以及数字滤波器的设计。实验结果表明,所设计的超高频RFID阅读器简化了前端电路系统结构,提升了稳定性,增强了抗干扰能力。该电路系统在信噪比较低的情况下,能够较好地实现915MHz频率的射频接收和发送。In order to improve the reader UHF RFID system still has a higher ability to identify,in the case of low signal-to-noise ratio.The UHF RFID systems must comply with EPC Class 1 generation 2 standard.In this paper,the design of the circuit system based on Xilinx＇s XC6SLX16-2CSG324 FPGA chip,and presents UHF RFID RF front-end circuit with software radio based on FPGA system.Digital baseband modem and IF filter circuit is designed and implemented in the FPGA system,and focused on designing the structure of the RF front-end circuit,AD/DA conversion circuits,and digital filter.Experimental results show that the UHF RFID reader de...
标签： 915mhz 超高频 rfid 阅读 射频 前端 电路 设计
上传时间： 2022-04-17
上传用户：shjgzh
ContentsMIPI是什么？o D-PHY物理层特点•МIРI 的数据传送oDSI&CSI应用MIPI：手机产业处理界面MIPI协议是手机行业的领导者倡导一个开放的移动接口标准MIPI Spec：DCS-显示命令接口DBI-显示总线接口DPI-显示像素接口DSI一显示串行接口CSI一显示摄像接口D-PHY物理层MIPI特点低功耗模式·动态调整到低功耗模式、高速传送模式和低信号摆幅模式。高速模式每通道可以传送500-1000Mbps低成本物理层EMI（抗辐射）数据包报头（4 bytes）数据标识符（DI*1byte：包含虚拟数据通道[7：6]和数据类型[5：0].，数据包*2byte：要传送的数据，长度固定两个字节。误差校正码（ECC）"1byte：可以把两个位的错误纠正例程数据包报头（4 bytes）数据标识符（Di）*1byte：包含虚拟数据通道[7：6]和数据类型[5：0].字数（WC）*2byte：传送数据的长度，固定为两个字节错误校验码（ECC）*1byte：可以修复两个位的错误有效传送数据（0~65535 bytes）最大字节-2^16.数据包页脚（2 bytes）：校验如果数据包的有效长度为0，那么校验位为FFFFh如果校验码不能计算，那么校验码的值为0000h数据包的长度：e4+（0-65535）+2-6~ 65541 bytesSync Event（H Start，H end，v Start，V end），Data Type =xx 0001（x1h）同步事件是两个字的数据包（1个字节的指令和一个字节的校验，因些他们可以精确的表示同步事件的开始和结束.干单个司步开始或同步结束事件的长度和位置在前面的图中有说明。同步事件的定义如下：Data Type= 00 0001（01h）场同步开始Data Type= 01 0001（11h）场同步结束Data Type= 10 0001（21b）行同步开始.Data Type= 11 0001（31h）行同步结束为了尽可能精确的体理一个同步事件，那么开始标识位必须放在第一位，结束标识位必须放在最后一位，行同步也是一样。同步事件的开始和结束应该是成对出现的，假如只有一个同步事件（通常是开始），那么这个数据也是可以传送出去的。
标签： mipi
上传时间： 2022-05-08
上传用户：
In this presentation, we will look at what the Serial Peripheral Interface, otherwise known as the SPI, is. and how it is used to communicate data to and from the PICmicro microcontroller.SPl is frequently used when few 1/O lines are available, but communication between two or more devices must be fast and easy to implement.In this presentation, we will discuss the following topics: We will first cover an Overview of SPI This section of the tutorial will introduce you to SPI and its concepts.Next, we will examine the use of SPI on the PICmicro MCU.The details of how SPI is implemented on a PICmicro device will be examined.Then, a Code Walkthrough will be given.The walkthough will explore code for both an SPI Master and SPI Slave. The example will have the Master generate data for sending to the slave.Finally, there will be a few resources given at the end of the presentation. These resources will allow you to explore in more detail the SPI interface
标签： spi协议
上传时间： 2022-06-20
上传用户：
一、建焊盘打开建立焊盘的软件Pad Designer路径：包括采用的制式，现在选公制单位毫米，精度3，右侧问是否需要多重钻孔，这个功能一般是用于做非圆孔。一般圆孔不用勾选。下面设定钻孔样式，一般是圆孔，钻孔内部是否镀铜 plated（no plated即为不镀铜，一般用于塑胶件定位孔），再是钻孔直径，设置精度，是否偏移等。如果是表贴元件，钻孔直径设为0。如果是表面安装元件，把signle layer mode勾选。焊盘一般需要 begin layer和end layer，还有就是soldmask_top，soldmask_bottom，pastemask top，pastemask bottom这几个层面。对表面安装元件来说，只需要begin layer，soldermask_top以及pastemask_top就可以了。鼠标左键点击begin layer，会发现最下面三个对话框被刷新，在下面填入需要的值：从左到右：规则焊盘，热焊盘，反焊盘。1规则焊盘下面需要填入焊盘形状，长宽，是否有偏移。1热焊盘，要求选择焊盘类型，尺寸等；1反焊盘，作用是设定焊盘与周边间距，一般比规则焊盘略大6-10mil。鼠标点击soldermask_top，下面对话框刷新出该选项。按照需要填入数据。Pastemask top同样处理。右边上角还有视图角度选择，Xsection为水平视图，TOP为从上往下看。
标签： cadence allegro
上传时间： 2022-07-02
上传用户：XuVshu
MotioninterfaceTM is becoming a "must-have"function being adopted by smartphone and tablet manufacturers due to the enormous value it adds to the end user experience. In smartphones, it finds use in applications such as gesture commands for applications and phone control, enhanced gaming, augmented reality, panoramic photo capture and viewing, and pedestrian and vehicle navigation. With its ability to precisely and accurately track user motions, MotionTracking technology can convert handsets and tablets into powerful 3D intelligent devices that can be used in applications ranging from health and fitness monitoring to location-based services. Key requirements for Motionlnterface enabled devices are small package size, low power consumption, high accuracy and repeatability, high shock tolerance, and application specific performance programmability-all at a low consumer price point.
标签： mpu6050
上传时间： 2022-07-06
上传用户：zhaiyawei
VIP专区-嵌入式/单片机编程源码精选合集系列（1）资源包含以下内容：1. 一个微型的tcp栈实现.2. 对am29f040的flash的操作.3. 一个含socket接口的小型tcp/ip协议栈.4. 一个测试端口测试程序.5. 压缩包中一个为一般操作系统下的fft.6. AES快速算法和蓝牙设备中用的E0算法(用于加密)、E1算法、E2算法、E3算法（用于密钥管理和鉴权等）等.7. 一个日历时钟DS12887或146818的C语言源程序.8. 一个ascii 码值计算原代码的例子.9. 一个嵌入式操作系统(microwindows)的源代码.10. nut/OS的源码.11. 嵌入式开发中的一些图形函数与汉字处理程序.12. 嵌入式触摸屏实验.13. C语言显示汉字.14. 日本的实时嵌入式操作系统norti源码.15. internich公司实现的一个非常非常小的OS.16. 在WinCe平台上开发的数据库管理程序,里面有一个可排序列表控件的实现和Excel的CVS文件的读写类.17. 任天堂模拟器.18. 一个漂亮.19. 怎样建立一个最小的linux系统.20. rtlinux3.0 的源代码.21. Low end Microchip PICs C函数.22. 一个利用中断修改后进行的A/D采集功能的使用软件..23. asm 开发.24. c_c++嵌入式系统编程.25. 控制系统组态软件的开发.26. 电动机书籍和电动机手册全集.27. 数字信号处理c语言程序集.28. CEComm: Windows CE 4.0下的串口调试程序 串口精灵源代码 TTY:Windows 下的类似超级终端的原代码. TAPICase: Windows 下用TAPI拨号的例子 image.29. MZ28AT命令说明书.doc.30. jtag工具.31. 嵌入式GUI 系统..32. 此程序实现了类似protel电路画图程序。.33. 液晶取字模程序.34. 嵌入式web平台.35. 嵌入式 Web Server 源码.36. 嵌入式 Web Server 源码.37. 嵌入式软件VP310tuner驱动程序.38. vp310.39. 44b0+lwip.40. cypress fx2扩展io代码.
上传时间： 2013-06-14
上传用户：eeworm
