text disabled
上传时间： 2013-12-22
上传用户：wang0123456789
The SN65LBC170 and SN75LBC170 aremonolithic integrated circuits designed forbidirectional data communication on multipointbus-transmission lines. Potential applicationsinclude serial or parallel data transmission, cabledperipheral buses with twin axial, ribbon, ortwisted-pair cabling. These devices are suitablefor FAST-20 SCSI and can transmit or receivedata pulses as short as 25 ns, with skew lessthan 3 ns.These devices combine three 3-state differentialline drivers and three differential input linereceivers, all of which operate from a single 5-Vpower supply.The driver differential outputs and the receiverdifferential inputs are connected internally to formthree differential input/output (I/O) bus ports thatare designed to offer minimum loading to the buswhenever the driver is disabled or VCC = 0. Theseports feature a wide common-mode voltage rangemaking the device suitable for party-lineapplications over long cable runs.
上传时间： 2013-10-13
上传用户：ytulpx
The PCA9541 is a 2-to-1 I2C-bus master selector designed for high reliability dual masterI2C-bus applications where system operation is required, even when one master fails orthe controller card is removed for maintenance. The two masters (for example, primaryand back-up) are located on separate I2C-buses that connect to the same downstreamI2C-bus slave devices. I2C-bus commands are sent by either I2C-bus master and are usedto select one master at a time. Either master at any time can gain control of the slavedevices if the other master is disabled or removed from the system. The failed master isisolated from the system and will not affect communication between the on-line masterand the slave devices on the downstream I2C-bus.
上传时间： 2013-10-09
上传用户：3294322651
This example provides a description of how to use the USART with hardware flowcontrol and communicate with the Hyperterminal.First, the USART2 sends the TxBuffer to the hyperterminal and still waiting fora string from the hyperterminal that you must enter which must end by '\r'character (keypad ENTER button). Each byte received is retransmitted to theHyperterminal. The string that you have entered is stored in the RxBuffer array. The receivebuffer have a RxBufferSize bytes as maximum. The USART2 is configured as follow: - BaudRate = 115200 baud - Word Length = 8 Bits - One Stop Bit - No parity - Hardware flow control enabled (RTS and CTS signals) - Receive and transmit enabled - USART Clock disabled - USART CPOL: Clock is active low - USART CPHA: Data is captured on the second edge - USART LastBit: The clock pulse of the last data bit is not output to the SCLK pin
上传时间： 2013-10-31
上传用户：yy_cn
TIMER.ASM ********* [ milindhp@tifrvax.tifr.res.in ] Set Processor configuration word as = 0000 0000 1010 b. a] -MCLR tied to VDD (internally). b] Code protection off. c] WDT disabled. d] Internal RC oscillator [4 MHZ].
标签： configuration Processor milindhp tifrvax
上传时间： 2015-05-24
上传用户：wqxstar
SAM9261 BasicMMU Example code with ADS1.2 (163 kB) The goal of this project is to show how to use a PC100 SDRAM and the MMU to perform a rating with a 100MHz Bus Clock. The rating is based on Dhrystone 2.1. It shows the rate when I+D Caches are disabled or enabled, with or without MMU and I Cache is disable or enabled, with or without MMU.
标签： BasicMMU Example project 9261
上传时间： 2013-12-28
上传用户：zhanditian
EDB (Evan s Debugger) is a QT4 based binary mode debugger with the goal of having usability on par with OllyDbg. It uses a plugin architecture, so adding new features can be done with ease. The current release is for Linux, but future releases will target more platforms. Release focus: Major feature enhancements Changes: A new disassembly engine. A bug that could cause crashing was fixed. There is a new flags breakdown in the register view, an environment view plugin, and improved analysis (including a good speed increase). A bug in QT where disabled events could be triggered has been worked around.
标签： usability Debugger debugger binary
上传时间： 2013-12-21
上传用户：gundamwzc
The source code for this package is located in src/gov/nist/sip/proxy. The proxy is a pure JAIN-SIP application: it does not need proprietary nist-sip classes in addition of those defined in JAIN-SIP 1.1, you can substitute the NIST-SIP stack by another JAIN-SIP-1.1 compliant stack and it should interoperate. he proxy can act as presence server and be able to process NOTIFY and SUBSCRIBE requests. If this parameter is disabled, the proxy will simply forward those kind of requests following the appropriate routing decision.
标签： proxy The JAIN-SIP package
上传时间： 2015-11-30
上传用户：ippler8
NAME: u2440mon.c DESC: u2440mon entry point,menu,download HISTORY: Mar.25.2002:purnnamu: S3C2400X profile.c is ported for S3C2410X. Mar.27.2002:purnnamu: DMA is enabled. Apr.01.2002:purnnamu: isDownloadReady flag is added. Apr.10.2002:purnnamu: - Selecting menu is available in the waiting loop. So, isDownloadReady flag gets not needed - UART ch.1 can be selected for the console. Aug.20.2002:purnnamu: revision number change 0.2 -> R1.1 Sep.03.2002:purnnamu: To remove the power noise in the USB signal, the unused CLKOUT0,1 is disabled.
标签： 2440 mon download purnnamu
上传时间： 2016-05-12
上传用户：wff
I made a lot of changed on this object,such as * // 1.Encapsulates all code in one userobjet,since PB does not * // support "Address of Function" , so we can not set new * // WndProc, just makes the object more easy to use. * // 2.Uses structure array instead of Datastore * // 3.Calc width of menuitem at runtime(MEASUREITEM) * // 4.Draw disabled status
标签： Encapsulates userobjet changed object
上传时间： 2014-01-14
上传用户：lx9076
