fast calculation of image moments based on Fluss and Tuk s method described in "On the Calculation of Moments"
标签： calculation described Calculat moments
上传时间： 2013-12-24
上传用户：515414293
fuzzy systems for wind has been described in this controller run using matlab
标签： controller described systems matlab
上传时间： 2017-07-05
上传用户：亚亚娟娟123
Feeding antennas with proper signals can be difficult. The signal is often described as a voltage, and voltages are not well defined in electromagnetic wave formulations. There are several tricks to model voltage generators in such situations, and one is the magnetic frill. This model shows the basic steps of defining a magnetic frill voltage generator for a dipole antenna, and it also compares the resulting antenna impedance with known results.
标签： difficult described antennas Feeding
上传时间： 2013-12-25
上传用户：yulg
Feeding antennas with proper signals can be difficult. The signal is often described as a voltage, and voltages are not well defined in electromagnetic wave formulations. There are several tricks to model voltage generators in such situations, and one is the magnetic frill. This model shows the basic steps of defining a magnetic frill voltage generator for a dipole antenna, and it also compares the resulting antenna impedance with known results.
标签： difficult described antennas Feeding
上传时间： 2013-12-21
上传用户：GavinNeko
Fp Growth sample, found on other sites with the main part described.
标签： described Growth sample found
上传时间： 2013-12-15
上传用户：xlcky
本书阐述了用vc++来开发usb接口的程序。开发环境：vc6.0，格式：pdf-The book described by vc++ To develop procedures for usb int
标签： writeUSBprogram VC
上传时间： 2013-07-26
上传用户：asdfasdfd
This note describes some of the unique IC design techniques incorporated into a fast, monolithic power buffer, the LT1010. Also, some application ideas are described such as capacitive load driving, boosting fast op amp output current and power supply circuits.
上传时间： 2013-11-12
上传用户：671145514
针对科研实验中对拉压千斤顶加载过程控制的需要，采用ATmega128单片机控制步进电机进而实现对执行系统的电动泵站实行自动控制。对力和位移的数据采集与处理及用步进电机控制电动泵站手柄的技术细节作了重点描述。通过单片机的A/D变换器对AMP放大模块采集的电桥信号作量化处理，千斤顶的操控手柄位置依电动油泵阀门开启的方向和大小作若干定位，单片机根据力或位移传感器信号，实时控制步进电机驱动手柄旋转到相应操控位置。 Abstract: This article describes the use of ATmega128 AVR microcontroller series of DBS electric pumping stations and QF100/200 separate twoway hydraulic jack to automate the process of manipulating the work of the technical content. Articles on force and displacement data acquisition and processing， and stepper motor control electric pump with the handle of the key technical details were described. Through the MCU’s A / D converter module is collected on the AMP amplification quantify the signal bridge， jack handle position control valve opening according to the direction of electric pumps for a number of positioning and size of the microcontroller based on force or displacement sensor signals， real-time control stepper motor drive control handle rotate to the appropriate location.
上传时间： 2014-01-16
上传用户：hasan2015
详细介绍工控软件组态王与单片机多机串口通讯的设计原理。分析组态王提供的直接与单片机串口通信方法的优点，给出系统基于RS-485总线传输的接口电路原理图。根据组态王提供的通讯协议和单片机多机串口通讯的原理，给出程序设计流程与思路。 Abstract: In this paper，the design principle of communication between multi-SCM and KingView by serial ports is described in detail.We analysis the advantage of method supplied by KingView,by which KingView can communicate with serial ports of SCM directly，and provide the system’s interface circuit based on the RS-485transmission line.We provide flow diagram of programming and thinking on the basis of communication protocol supplied by KingView and principle of communication among multi-SCM through serial ports.
上传时间： 2013-12-19
上传用户：tecman
介绍了当前普通标记机控制系统现状及其存在缺点，给出气动标记机及相频修正PWM模式的工作原理。采用ATmega16单片机和USB转换RS232接口器件CH341T实现驱动控制系统与PC的实时通讯，标记控制系统可升级到USB接口。采用基于ATmega16的相频修正PWM替换555振荡电路产生的PWM，可直接通过软件调整PWM信号。使用达林顿三极管TIP122替代直流继电器驱动高频电磁阀，使得电磁阀驱动电路简单，成本低廉。该控制系统已成功应用于气动标记机。 Abstract: In this paper,the actuality and demerit of the common gas marking machine control systems are described.The operation principle of the gas marking machine and the phase and frequency correct PWM of ATmega16is introduced.The real-time communication between the driving control system and PC by CH341T which its function is translated USB to RS232is realized,the control systems is updated grade to USB interface.The PWM signal can be adjustable by software for the555surge circuit was substituted by the phase and frequency.The high frequency electromagnetic value’s driving circuit by DC relay is replaced by TIP122,therefore,the circuit is become simple and the cost cheap.The control systems has been widely used in gas marking machine.
上传时间： 2013-10-18
上传用户：1427796291
