Advances in low power electronics now allow placementof battery-powered sensors and other devices in locationsfar from the power grid. Ideally, for true grid independence,the batteries should not need replacement, but instead berecharged using locally available renewable energy, suchas solar power. This Design Note shows how to producea compact battery charger that operates from a small2-cell solar panel. A unique feature of this design is thatthe DC/DC converter uses power point control to extractmaximum power from the solar panel.
上传时间： 2014-01-20
上传用户：wettetw
Linear Technology’s DC/DC step-down μModule®regulators are complete switchmode power supplies in asurface-mount package. They include the DC/DC controller,inductor, power switches and supporting circuitry.These highly integrated regulators also provide an easysolution for applications that require negative outputvoltages. In other words, these products can operate asinverting buck-boost regulators. As a result, the lowestpotential in the circuit is not the standard 0V, but –VOUT,which must be tied to the μModule regulator’s GND. Allsignals are now referred to –VOUT.
上传时间： 2013-10-22
上传用户：ztj182002
The LTC®3610 is a high power monolithic synchronousstep-down DC/DC regulator that can deliver up to 12Aof continuous output current from a 4V to 24V (28Vmaximum) input supply. It is a member of a high currentmonolithic regulator family (see Table 1) that featuresintegrated low RDS(ON) N-channel top and bottomMOSFETs. This results in a high effi ciency and highpower density solution with few external components.This regulator family uses a constant on-time valleycurrent mode architecture that is capable of operatingat very low duty cycles at high frequency and with veryfast transient response. All are available in low profi le(0.9mm max) QFN packages.
上传时间： 2013-11-07
上传用户：moerwang
A recent trend in the design of portable devices has beento use ceramic capacitors to filter DC/DC converter inputs.Ceramic capacitors are often chosen because of theirsmall size, low equivalent series resistance (ESR) and highRMS current capability. Also, recently, designers havebeen looking to ceramic capacitors due to shortages oftantalum capacitors.
上传时间： 2013-11-05
上传用户：comer1123
The LTM4600 DC/DC μModule regulator is a complete highpower density stepdown regulator for 10A continuous (14Apeak) loads. The device has two voltage options: 20VINmaximum for the LTM4600EV and 28VIN maximum for theLTM4600HVEV each housed in a small 15mm ¥ 15mm ¥2.8mm LGA surface mount package.
上传时间： 2013-10-10
上传用户：adada
The design of battery-powered equipment can often bequite challenging. Since few ICs can operate directly fromthe end-of-life voltage from a 2-cell battery (about 1.8V),most systems require a DC/DCconverter. The systemdesigner often has a limited area in which to place the DC/DC converter; associated inductors and capacitors must be
上传时间： 2013-11-23
上传用户：wys0120
The latest generation of Texas Instruments (TI) boardmountedpower modules utilizes a pin interconnect technologythat improves surface-mount manufacturability.These modules are produced as a double-sided surfacemount(DSSMT) subassembly, yielding a case-less constructionwith subcomponents located on both sides of theprinted circuit board (PCB). Products produced in theDSSMT outline use the latest high-efficiency topologiesand magnetic-component packaging. This providescustomers with a high-efficiency, ready-to-use switchingpower module in a compact, space-saving package. Bothnonisolated point-of-load (POL) switching regulators andthe isolated dc/dc converter modules are being producedin the DSSMT outline.TI’s plug-in power product line offers power modules inboth through-hole and surface-mount packages. The surfacemountmodules produced in the DSSMT outline use asolid copper interconnect with an integral solder ball fortheir
上传时间： 2013-10-10
上传用户：1184599859
简介采用模数转换器(ADC)的现代电子系统要求更低功耗和更高性能。本文描述了采用线性电源和开关电源之间的差异，并论证了将高效DC-DC转换器和高性能模数转换器组合使用，可以显著降低系统功耗，同时不降低模数转换器的性能。
上传时间： 2013-10-27
上传用户：哈哈hah
加利福尼亚州米尔皮塔斯 (MILPITAS, CA) – 2009 年 8 月 31 日 – 凌力尔特公司 (Linear Technology Corporation) 推出隔离式 RS485 微型模块 (uModule®) 收发器 LTM2881，该器件针对大的地至地差分电压和共模瞬变提供了保护作用。在实际的 RS485系统中，各节点之间的地电位差异很大，常常超出可容许范围，这有可能导致通信中断或收发器受损。LTM2881 运用内部感应信号隔离来对逻辑电平接口和线路收发器实施隔离，以中断接地环路，从而实现了大得多的共模电压范围和 >30kV/μs 的卓越共模抑制性能。一个低 EMI DC-DC 转换器负责向收发器供电，并提供了一个用于给任何外部支持元件供电的 5V 隔离电源输出。凭借 2,500VRMS 的电流隔离、板上辅助电源和一个完全符合标准的 RS485 发送器和接收器，LTM2881 不需要使用外部元件，从而确保了一款适合隔离串行数据通信的完整、小型μModule 解决方案。
上传时间： 2013-10-25
上传用户：ljj722
常见DC/DC电源变换器的拓扑类型见表1～表3所列。表中给出不同的电路结构，同时也给出相应的电压及电流波形(设相关的电感电流为连续工作方式)。PWM表示脉宽调制波形，U1为直流输入电压，UDS为功率丌关管S1(MOSFFT)的漏一源极电压。ID1为S1的漏极电流。IF1为D1的工作电流，U0为输出电压，IL为负载电流。T为周期，t为UO呈高电平(或低电平)的时问及开关导通时间，D为占空比，有关系式：D=t/T。C1、C2均为输入端滤波电容，CO为输出端滤波电容，L1、L2为电感。 1、常见单管DC/DC电源变换器
上传时间： 2013-10-19
上传用户：1966640071
