介绍了基于单片机C8051F020的通用串口适配器的设计与实现方法，即由单片机控制的智能化一对多口收发信号转换器。通过采用C51对单片机进行编程，控制与RS-232（标准RS-232电平）、RS232(TTL电平)、RS-422接口的数据通信；采用C++ Builder作为开发平台，通过RS-232接口实现上位机对适配器各个通信端口的控制。 Abstract: Design and realization of a universal serial port adapter based on the MCU C8051F020 are introduced.The adapter is an intelligent one-to-more receiving and transmitting signal converter controlled by the MCU. By programming the MCU with the language C51,MCU control data communication between the MCU and RS-232(RS-232 level),RS-232(TTL level),RS-422 port; Using C++ Builder as the development plane, by one RS232 port, the upper PC can control each of the communication port of the adapter.
上传时间： 2013-11-19
上传用户：hebanlian
介绍了电力操作电源与智能电池巡检系统的特点，给出了一种基于超低功耗单片机MSP430 F149针对中小型变电站自动化运行的专用设备的基本设计原理及实现方法，最后给出了详细硬件构成和软件实现。该系统能满足中小型变电站安全、可靠、自动运行的要求，并通过与上位机的串行通信实现变电站的远程管理和控制。 Abstract: The characters of the intelligent battery data logging system of the electric operation power are introduced.The basic design principle and the implemented methods of the special equipment which only designed for the middle or small transformer substation based on MSP430F149 are prescribed. Finally, the hardware block diagram and the software flow chart are also given. The function that the system finally needs to realize can basically meet with the middle or small transformer substation’s satisfy, reliably,and automatic running.And it can also realize the transformer substation long-distance management and control by serial communicating with the host computer.
上传时间： 2013-11-25
上传用户：黄华强
基于幅移键控技术ASK（Amplitude-Shift Keying），以C8051F340单片机作为监测终端控制器，C8051F330D单片机作为探测节点控制器，采用半双工的通信方式，通过监控终端和探测节点的无线收发电路，实现数据的双向无线传输。收发电路采用直径为0.8 mm的漆包线自行绕制成圆形空心线圈天线，天线直径为（3.4±0.3）cm。试验表明，探测节点与监测终端的通信距离为24 cm，通过桥接方式，节点收发功率为102 mW时，节点间的通信距离可达20 cm。与传统无线收发模块相比，该无线收发电路在受体积、功耗、成本限制的场合有广阔的应用前景。 Abstract: Based on ASK technology and with the C8051F340 and C8051F330D MCU as the controller， using half-duplex communication mode， this paper achieves bi-directional data transfer. Transceiver circuit constituted by enameled wire which diameter is 0.8mm and wound into a diameter （3.4±0.3） cm circular hollow coil antenna. Tests show that the communication distance between detection and monitoring of the terminal is 24cm，the distance is up to 20cm between two nodes when using the manner of bridging and the node transceiver power is 102mW. Compared with the conventional wireless transceiver modules， the circuit has wide application prospect in small size， low cost and low power consumption and other characteristics.
上传时间： 2013-10-19
上传用户：xz85592677
为了在工业生产及过程控制中准确测量温度，设计了一种基于低功耗MSP430单片机的数字温度计。整个系统通过单片机MSP430F1121A控制DS18B20读取温度，采用数码管显示，温度传感器DS18B20与单片机之间通过串口进行数据传输。MSP430系列单片机具有超低功耗，且外围的整合性高，DS18B20只需一个端口即可实现数据通信，连接方便。通过多次实验证明，该系统的测试结果与实际环境温度一致，除了具有接口电路简单、测量精度高、误差小、可靠性高等特点外，其低成本、低功耗的特点使其拥有更广阔的应用前景。 Abstract: In order to obtain accurate measuring temperature in industrial production and process control， a digital thermometer based on MSP430 MCU is designed. The system uses MSP430F1121A MCU to control DS18B20， and gets the temperature data， which is displayed on the LED. The temperature sensor DS18B20 and MCU transmit data through serial communication. MSP430 series has ultra-low power and high integration， DS18B20 only needs one port to achieve data communication. Through many experimental results prove， this system is consistent with actual environment temperature. The system has characteristics of interface circuit simple， high measuring accuracy， minor error， high reliability， besides， the characteristics of low cost and low power make it having vaster application prospect.
上传时间： 2013-10-16
上传用户：wettetw
基于AT89C52单片机的步进电机控制系统设计 摘 要: 提出了一个由AT89C52单片机控制步进电机的实例。可以通过键盘输入相关数据, 并根据需要, 实时对步进电机工作方式进行设置, 具有实时性和交互性的特点。该系统可应用于步进电机控制的大多数场合。实践表明, 系统性能优于传统的步进电机控制器。 关键词: 单片机; 步进电动机; 直流固态继电器; 实时控制 ABSTRACT: A stepp ing motor control system based on AT89C52 chip microcomputer was described.The data can be inputwith keyboard, and stepp ingmotorwas controlled by these data. According to the demand, users can set the workingmodel of stepp ingmotor in real2time. This system can be widely used in stepp ing motor controlling. The p ractice showed that the performance of this system outdid the tradi-tional stepp ing motor controller.
上传时间： 2013-11-22
上传用户：vodssv
基于LabVIEW和单片机的空调温度场测量系统的研究:室内温度是空调系统舒适性的重要指标,对其及时、准确地测量显得非常重要。介绍单片机AT89C51 和数字式、单总线型温度传感器DS18B20 组成矩形测量网络采集空调室内40 点温度,LabVIEW作为开发平台,二者之间通过串口实现数据通信,利用LabVIEW强大的数据处理和显示功能对采集的空调温度场数据进行实时处理、分析和显示,详细介绍了系统的硬件结构和软件模块的设计方案。关键词:单片机;DS18B20 ;LabVIEW;串行通信 Abstract : Temperature is a very important criterion of air condition system′s comfort , so it is very significant to measure it accurately and real timely. This paper int roduces a data acquisition system of measuring 40 point s temperature for air condition room based on single wire digital sensor DS18B20 and microcont roller AT89C51 which are composed of rectangle measuring meshwork. The data communication between LabVIEW and microcont roller is executed via serial port ,and the temperature field data of air condition room are processed analyzed and displayed on LabVIEW. The hardware and software modules are also given in detail.Keywords : single chip ;DS18B20 ;LabVIEW; serial communication
上传时间： 2014-05-05
上传用户：KSLYZ
提出了一个由AT89C52单片机控制步进电机的实例。可以通过键盘输入相关数据, 并根据需要, 实时对步进电机工作方式进行设置, 具有实时性和交互性的特点。该系统可应用于步进电机控制的大多数场合。实践表明, 系统性能优于传统的步进电机控制器。关键词: 单片机; 步进电动机; 直流固态继电器; 实时控制Con trol System of Stepp ingMotor Ba sed on AT89C52 ChipM icrocomputerMENGWu2sheng, L ILiang (College of Automatization, Northwestern Polytechnical Unversity, Xipan 710072, China)ABSTRACT: A stepp ing motor control system based on AT89C52 chip microcomputer was described.The data can be inputwith keyboard, and stepp ingmotorwas controlled by these data. According to the demand, users can set the workingmodel of stepp ingmotor in real2time. This system can be widely used in stepp ing motor controlling. The p ractice showed that the performance of this system outdid the tradi tional stepp ing motor controller.KEY WORDS: Chip microcomputer; Stepp ingmotor; DCSSR; Real2time control
标签： Control System ingMot Stepp
上传时间： 2013-11-19
上传用户：leesuper
基于多点网络的水厂自动监控系统设计Design of MPI Based Automatic Monitoring and Control System in Water Works刘 美 俊(湖南工程学院，湘潭411101)摘要针对水厂工作水泵多、现场离控制站距离远的特点，提出了一种基于MPI多点网络的自动监控系统的设计方法，分析了系统的工作原理，介绍了系统中数据的采集与处理、主站与从站的通信原理以及系统软件的设计。由于这种系统的主、从站PLC之间采用MPI网络通信，具有运行可靠、性能价格比高的特点，所以适用于中小规模水厂的分布式监控场合。关键词多点网络主站从站监控系统Abstract Ina ccordancew ithth efe atuersof w aterw orks,i. e. ，manyp umpsin o perationa ndth ep umps， farfor mt hec ontrolst ation,th em ethodo fdesigninga na utomati(〕monitoringa ndc ontorlsy stemb asedo nM PIis p resented.Th eo perationalpr incipleo fth esy stemi san alyzed,th ed atac olection,data processing; communication between master station and slave station as wel as design and system software are discussed. Because MPI network communicationis used among master station, slave stations and PLC, the system is reliable and high cost-efective. It is， suitable for smal and mediumsized water works for distrbuted monitoring and control.Keywords MPI Masterst ation Slaves tation Monitoringa ndc ontorlsy stem 自来 水 厂 的自动控制系统一般分为两大部分，一对组态硬件要求较高，投资较大。相对而言，MPI网是水源地深水泵的工作控制，一是水厂区变频恒压供络速度可达187.5 M bps，通过一级中继器传输距离可水控制，两部分的实际距离通常都比较远。某厂水源达Ikm 。根据水厂的具体情况，确定以MPI方式组地有3台深井泵给水厂区的蓄水池供水。水厂区的成网络，主站PLC为S7-300系列的CPU3121FM，从任务是对水池的水进行消毒处理后，通过加压泵向管站为S7-200系列的CPU222。这样既满足了系统要路恒压供水。选用Siemens公司的S7系列可编程控求，又相对于Profibus网络节省了三分之一的成本，制器(PLC)和上位机组成实时数据采集和监控系统， 这种分布式监控系统具有较高的性能价格比。系统对深水泵进行远程控制，对供水泵采用变频器进行恒中PLC的物理层采用RS - 485接口，网络延伸选用压控制以保证整个水厂的电机设备安全、可靠地运带防雷保护的中继器，使系统的安全运行得到了保行。证。MPI网络的拓扑结构如图1所示。1 多点网络(NWI)监控系统的组成Sie me ns 公司S7系列PLC通常有MP」多点网络与Profibus现场总线网络两种组网方式。Profibus现场总线的应用目前较为普遍，通用性较好，它由Profibus一DP, Profibus一FMS, Profibus一PA组成。Profibus - DP型用于分散外设间的数据传输，传输速率为9.6kbps一12Mbps，主要用于现场控制器与分散1/0之间的通信，可满足交直流调速系统快速响应的时间要求，特别适合于加工自动化领域的应用;Profibus - FMS主要解决车间级通信问题，完成中等传输速度的循环或非循环数据交换任务，适用于纺织、楼宇自动化、可编程控制器、低压开关等;Profibus - PA型采用了OSI模型的物理层和数据链路层，适用于过程自动化的总线类型。
上传时间： 2013-10-09
上传用户：fac1003
基于USB接口的数据采集模块的设计与实现Design and Implementation of USB-Based Data Acquisition Module路 永 伸(天津科技大学电子信息与自动化学院，天津300222)摘要文中给出基于USB接口的数据采集模块的设计与实现。硬件设计采用以Adpc831与PDIUSBDI2为主的器件进行硬件设计，采用Windriver开发USB驱动，并用Visual C十十6.0对主机软件中硬件接口操作部分进行动态链接库封装。关键词USB 数据采集Adpc831 PDNSBDI2 Windriver动态链接库Abstract T hed esigna ndim plementaitono fU SB-BasedD ataA cquisiitonM oduleis g iven.Th ec hips oluitonm ainlyw ithA dpc831a ndP DTUSBD12i sused for hardware design. The USB drive is developed场Wmdriver, and the operation on the hardware interface is packaged into Dynamic Link Libraries场Visual C++6.0. Keywords USB DataA cquisition Adttc831 PDfUSBD12 Windriver0 引言US B总 线 是新一代接口总线，最初推出的目的是为了统一取代PC机的各类外设接口，迄今经历了1.0,1.1与2.0版本3个标准。在国内基于USB总线的相关设计与开发也得到了快速的发展，很多设计者从各自的应用领域，用不同方案设计出了相应的装置[1,2]。数据采集是工业控制中一个普遍而重要的环节，因此开发基于USB接口的数据采集模块具有很强的现实应用意义。虽然 US B总线标准已经发展到2.0版本，但由于工业控制现场干扰信号的情况比较复杂，高速数据传输的可靠性不容易被保证，并且很多场合对数据采集的实时性要求并不高，开发2.0标准产品的成本又较1.1标准产品高，所以笔者认为，在工业控制领域，目前开发基于USB总线1.1标准实现的数据采集模块的实用意义大于相应2.0标准模块。
上传时间： 2013-10-23
上传用户：q3290766
为了在CDMA系统中更好地应用QDPSK数字调制方式，在分析四相相对移相（QDPSK)信号调制解调原理的基础上，设计了一种QDPSK调制解调电路，它包括串并转换、差分编码、四相载波产生和选相、相干解调、差分译码和并串转换电路。在MAX+PLUSⅡ软件平台上，进行了编译和波形仿真。综合后下载到复杂可编程逻辑器件EPM7128SLC84-15中，测试结果表明，调制电路能正确选相，解调电路输出数据与QDPSK调制输入数据完全一致，达到了预期的设计要求。 Abstract: In order to realize the better application of digital modulation mode QDPSK in the CDMA system， a sort of QDPSK modulation-demodulation circuit was designed based on the analysis of QDPSK signal modulation-demodulation principles. It included serial/parallel conversion circuit, differential encoding circuit, four-phase carrier wave produced and phase chosen circuit, coherent demodulation circuit, difference decoding circuit and parallel/serial conversion circuit. And it was compiled and simulated on the MAX+PLUSⅡ software platform,and downloaded into the CPLD of EPM7128SLC84-15.The test result shows that the modulation circuit can exactly choose the phase，and the output data of the demodulator circuit is the same as the input data of the QDPSK modulate. The circuit achieves the prospective requirement of the design.
上传时间： 2014-01-13
上传用户：qoovoop
