高速板设计技术的PDF文档,详细的讲述了高速板走线应该注意的问题,希望对你有用!
上传时间: 2017-03-20
上传用户:lyy1234
高速板设计技术的PDF文档,详细的讲述了高速板走线应该注意的问题,希望对你有用!
上传时间: 2017-03-20
上传用户:myworkpost
择PCB板材必须在满足设计需求和可量产性及成本中间取得平衡点。设计需求包含电气和机构这两部分。通常在设计非常高速的PCB板子(大于GHz的频率)时这材质问题会比较重要。例如,现在常用的FR-4材质,在几个GHz的频率时的介质损(dielectric loss)会对信号衰减有很大的影响,可能就不合用。就电气而言,要注意介电常数(dielectric constant)和介质损在所设计的频率是否合用。
上传时间: 2017-04-29
上传用户:VRMMO
定时器T1方式1+软件计数循环定时1Sec,控制LED闪烁,加入中断函数
上传时间: 2013-12-26
上传用户:asddsd
长数显示清无效零,连续触发清有重启功能,用于计数清零器中
上传时间: 2017-05-26
上传用户:kikye
本代码为编码开关代码,编码开关也就是数字音响中的 360度旋转的数字音量以及显示器上用的(单键飞梭开 关)等类似鼠标滚轮的手动计数输入设备。 我使用的编码开关为5个引脚的,其中2个引脚为按下 转轮开关(也就相当于鼠标中键)。另外3个引脚用来 检测旋转方向以及旋转步数的检测端。引脚分别为a,b,c b接地a,c分别接到P2.0和P2.1口并分别接两个10K上拉 电阻,并且a,c需要分别对地接一个104的电容,否则 因为编码开关的触点抖动会引起轻微误动作。本程序不 使用定时器,不占用中断,不使用延时代码,并对每个 细分步数进行判断,避免一切误动作,性能超级稳定。 我使用的编码器是APLS的EC11B可以参照附件的时序图 编码器控制流水灯最能说明问题,下面是以一段流水 灯来演示。
上传时间: 2017-07-03
上传用户:gaojiao1999
用2*2矩阵键盘实现手动计数,我用的是单片机中断实现该功能
上传时间: 2017-07-15
上传用户:sxdtlqqjl
高速PCB设计指南,对在设计高速PCB的过程中需要注意的问题进行了分析和介绍。
上传时间: 2017-07-22
上传用户:chenbhdt
(1)用8 个LED 发光管的来回滚动显示或跳跃运动显示来模拟靶的移动,用按1~8 数字键(对应8 个LED)来模拟射击,如果在某个LED 点亮期间按下相应数字键,表示射中并熄灯(全部熄),记录射中次数。 (2)比赛规则可有以下两种: 比赛规则1:靶始终来回不断地移动(一旦射中则从头开始滚动),在规定的时间(如50 秒)和规定的射击次数(如20 次)内看谁的射中次数多谁获胜; 比赛规则2:总共有若干个(如20 个)移动靶,每个靶的移动时间限制在一定的时间范围内(如5 秒),要求在此时间内射击,若射中则记一分并出现下一个移动靶,若未射中或在规定时间内未射击则不记分并出现下一个移动靶。同样看谁的射中次数多谁就获胜。 (3) 要求精确定时中断计时
上传时间: 2017-07-30
上传用户:anng
该程序用事件管理器B的定时器4定时时间来触发A/D采样的启动。采样时采用级联模式,一次做16个转换,转换通道分别是0~15。转换完成后,在A/D中断服务子程序中将转换结果读出。该程序做一次A/D采样。
上传时间: 2017-09-25
上传用户:标点符号