Abstract: The application note addresses how G3-PLC, a powerline communications protocol approvedby the International Telecommunications Union (ITU), enables mesh networking in advanced metering
上传时间： 2013-11-17
上传用户：erkuizhang
本文主要通过介绍PLC通讯的意义和三菱FX系列PLC的四种通讯方式，并重点介绍FX系列PLC与计算机无协议通讯，主要从无协议通讯的硬件、配线、数据寄存器设置、PLC与计算机无协议通讯的指令用法、PLC程序编写和计算机VB程序的编写来说明无协议通讯的过程和一般方法。 My dissertation introduces the significance of PLC communications and the four means of communication of Mitsubishi FX’s PLC, And highlights the no protocol communications of FX series PLC and computer, no protocol communications hardware, wiring, Register data set, and the usage of command about no protocol communications, How to write PLC program and computer VB program to illustrate the process of no protocol communications and general method.
上传时间： 2014-11-29
上传用户：Jerry_Chow
The NCV7356 is a physical layer device for a single wire data linkcapable of operating with various Carrier Sense Multiple Accesswith Collision Resolution (CSMA/CR) protocols such as the BoschController Area Network (CAN) version 2.0. This serial data linknetwork is intended for use in applications where high data rate is notrequired and a lower data rate can achieve cost reductions in both thephysical media components and in the microprocessor and/ordedicated logic devices which use the network.The network shall be able to operate in either the normal data ratemode or a high-speed data download mode for assembly line andservice data transfer operations. The high-speed mode is onlyintended to be operational when the bus is attached to an off-boardservice node. This node shall provide temporary bus electrical loadswhich facilitate higher speed operation. Such temporary loads shouldbe removed when not performing download operations.The bit rate for normal communications is typically 33 kbit/s, forhigh-speed transmissions like described above a typical bit rate of83 kbit/s is recommended. The NCV7356 features undervoltagelockout, timeout for faulty blocked input signals, output blankingtime in case of bus ringing and a very low sleep mode current.
上传时间： 2013-10-24
上传用户：s蓝莓汁
The LPC2292/2294 microcontrollers are based on a 16/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, together with 256 kB of embedded high-speed flash memory. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at the maximum clock rate. For critical code size applications, the alternative 16-bit Thumb mode reduces code by more than 30 pct with minimal performance penalty. With their 144-pin package, low power consumption, various 32-bit timers, 8-channel 10-bit ADC, 2/4 (LPC2294) advanced CAN channels, PWM channels and up to nine external interrupt pins these microcontrollers are particularly suitable for automotive and industrial control applications as well as medical systems and fault-tolerant maintenance buses. The number of available fast GPIOs ranges from 76 (with external memory) through 112 (single-chip). With a wide range of additional serial communications interfaces, they are also suited for communication gateways and protocol converters as well as many other general-purpose applications. Remark: Throughout the data sheet, the term LPC2292/2294 will apply to devices with and without the /00 or /01 suffix. The suffixes /00 and /01 will be used to differentiate from other devices only when necessary.
上传时间： 2014-12-30
上传用户：aysyzxzm
Linear Technology offers some of the highest performance RF and signal chain solutions for wireless and cellularinfrastructure. These products support worldwide standards including, LTE, WiMAX, GSM,W-CDMA, TD-SCDMA,CDMA, and CDMA2000. Other wireless systems include broadband microwave data links, secure communications,satellite receivers, broadband wireless access, wireless broadcast systems, RFID readers and cable infrastructure
上传时间： 2013-11-04
上传用户：kiklkook
Abstract: While many questions still surround the creation and deployment of the smart grid, the need for a reliablecommunications infrastructure is indisputable. Developers of the IEEE 1901.2 standard identified difficult channel conditionscharacteristic of low-frequency powerline communications and implemented an orthogonal frequency division multiplexing (OFDM)architecture using advanced modulation and channel-coding techniques. This strategy helped to ensure a robust communicationsnetwork for the smart grid.
上传时间： 2013-10-18
上传用户：myworkpost
为满足无线网络技术具有低功耗、节点体积小、网络容量大、网络传输可靠等技术要求，设计了一种以MSP430单片机和CC2420射频收发器组成的无线传感节点。通过分析其节点组成，提出了ZigBee技术中的几种网络拓扑形式，并研究了ZigBee路由算法。针对不同的传输要求形式选用不同的网络拓扑形式可以尽大可能地减少系统成本。同时针对不同网络选用正确的ZigBee路由算法有效地减少了网络能量消耗，提高了系统的可靠性。应用试验表明，采用ZigBee方式通信可以提高传输速率且覆盖范围大，与传统的有线通信方式相比可以节约40%左右的成本。 Abstract: To improve the proposed technical requirements such as low-ower， small nodes， large capacity and reliable network transmission， wireless sensor nodes based on MSP430 MCU and CC2420 RF transceiver were designed. This paper provided network topology of ZigBee technology by analysing the component of the nodes and researched ZigBee routing algorithm. Aiming at different requirements of transmission mode to choose the different network topologies form can most likely reduce the system cost. And aiming at different network to choose the correct ZigBee routing algorithm can effectively reduced the network energy consumption and improved the reliability of the system. Results show that the communication which used ZigBee mode can improve the transmission rate， cover more area and reduce 40% cost compared with traditional wired communications mode.
上传时间： 2013-10-09
上传用户：robter
通过比较各种隔离数字通信的特点和应用范围，指出塑料光纤在隔离数字通信中的优势。使用已经标准化的TOSLINK接口，有利于节省硬件开发成本和简化设计难度。给出了塑料光纤的硬件驱动电路，说明设计过程中的注意事项，对光收发模块的电压特性和频率特性进行全面试验，并给出SPI口使用塑料光纤隔离通信的典型应用电路图。试验结果表明，该设计可为电力现场、电力电子及仪器仪表的设计提供参考。 Abstract: y comparing characteristics and applications area of various isolated digital communications， this article indicates advantages of plastic optical fiber in isolated digital communications. Using the standardized TOSLINK interface， it helps to control costs and difficulty in hardware development and design. Then it gives the hardware driver circuit of plastic optical fiber module， explains the noticed details in design process， gives results on the basis of the optical transceiver module voltage characteristics and frequency characteristics tests. Finally，it gives typical application circuit of the SPI communication port by using plastic optical fiber isolation .The results show that this design can be referenced for the power field， power electronics and instrumentation design.
上传时间： 2014-01-10
上传用户：gundan
Single-Ended and Differential S-Parameters Differential circuits have been important incommunication systems for many years. In the past,differential communication circuits operated at lowfrequencies, where they could be designed andanalyzed using lumped-element models andtechniques. With the frequency of operationincreasing beyond 1GHz, and above 1Gbps fordigital communications, this lumped-elementapproach is no longer valid, because the physicalsize of the circuit approaches the size of awavelength.Distributed models and analysis techniques are nowused instead of lumped-element techniques.Scattering parameters, or S-parameters, have beendeveloped for this purpose [1]. These S-parametersare defined for single-ended networks. S-parameterscan be used to describe differential networks, but astrict definition was not developed until Bockelmanand others addressed this issue [2]. Bockelman’swork also included a study on how to adapt single-ended S-parameters for use with differential circuits[2]. This adaptation, called “mixed-mode S-parameters,” addresses differential and common-mode operation, as well as the conversion betweenthe two modes of operation.This application note will explain the use of single-ended and mixed-mode S-parameters, and the basicconcepts of microwave measurement calibration.
上传时间： 2014-03-25
上传用户：yyyyyyyyyy
GSM是Global System For Mobile communications的缩写。由欧洲电信标准组织ETSI制订的一个数字移动通信标准。GSM是全球移动通信系统(Global System of Mobile communication) 的简称。它的空中接口采用时分多址技术。
上传时间： 2013-10-09
上传用户：1142895891
