The PCA9517 is a CMOS integrated circuit that provides level shifting between lowvoltage (down to 0.9 V) and higher voltage (2.7 V to 5.5 V) I2C-bus or SMBus applications.While retaining all the operating modes and features of the I2C-bus system during thelevel shifts, it also permits extension of the I2C-bus by providing bidirectional buffering forboth the data (SDA) and the clock (SCL) lines, thus enabling two buses of 400 pF. Usingthe PCA9517 enables the system designer to isolate two halves of a bus for both voltageand capacitance. The SDA and SCL pins are over voltage tolerant and arehigh-impedance when the PCA9517 is unpowered.
标签： translating Level 9517 PCA
上传时间： 2013-12-25
上传用户：wsf950131
The PCA9518 is a BiCMOS integrated circuit intended forapplication in I2C and SMBus systems.While retaining all the operating modes and features of the I2Csystem, it permits extension of the I2C-bus by buffering both thedata (SDA) and the clock (SCL) lines, thus enabling virtuallyunlimited buses of 400 pF.
标签： Expandable 5channel 9518 PCA
上传时间： 2013-10-23
上传用户：dumplin9
The PCA9541 is a 2-to-1 I2C-bus master selector designed for high reliability dual masterI2C-bus applications where system operation is required, even when one master fails orthe controller card is removed for maintenance. The two masters (for example, primaryand back-up) are located on separate I2C-buses that connect to the same downstreamI2C-bus slave devices. I2C-bus commands are sent by either I2C-bus master and are usedto select one master at a time. Either master at any time can gain control of the slavedevices if the other master is disabled or removed from the system. The failed master isisolated from the system and will not affect communication between the on-line masterand the slave devices on the downstream I2C-bus.
上传时间： 2013-10-09
上传用户：3294322651
The PCA9548A is an octal bidirectional translating switch controlled via the I2C-bus. TheSCL/SDA upstream pair fans out to eight downstream pairs, or channels. Any individualSCx/SDx channel or combination of channels can be selected, determined by thecontents of the programmable control register.An active LOW reset input allows the PCA9548A to recover from a situation where one ofthe downstream I2C-buses is stuck in a LOW state. Pulling the RESET pin LOW resets theI2C-bus state machine and causes all the channels to be deselected as does the internalPower-on reset function.
上传时间： 2013-10-13
上传用户：bakdesec
The LPC2292/2294 microcontrollers are based on a 16/32-bit ARM7TDMI-S CPU with real-time emulation and embedded trace support, together with 256 kB of embedded high-speed flash memory. A 128-bit wide memory interface and a unique accelerator architecture enable 32-bit code execution at the maximum clock rate. For critical code size applications, the alternative 16-bit Thumb mode reduces code by more than 30 pct with minimal performance penalty. With their 144-pin package, low power consumption, various 32-bit timers, 8-channel 10-bit ADC, 2/4 (LPC2294) advanced CAN channels, PWM channels and up to nine external interrupt pins these microcontrollers are particularly suitable for automotive and industrial control applications as well as medical systems and fault-tolerant maintenance buses. The number of available fast GPIOs ranges from 76 (with external memory) through 112 (single-chip). With a wide range of additional serial communications interfaces, they are also suited for communication gateways and protocol converters as well as many other general-purpose applications. Remark: Throughout the data sheet, the term LPC2292/2294 will apply to devices with and without the /00 or /01 suffix. The suffixes /00 and /01 will be used to differentiate from other devices only when necessary.
上传时间： 2014-12-30
上传用户：aysyzxzm
The LPC1850/30/20/10 are ARM Cortex-M3 based microcontrollers for embeddedapplications. The ARM Cortex-M3 is a next generation core that offers systemenhancements such as low power consumption, enhanced debug features, and a highlevel of support block integration.The LPC1850/30/20/10 operate at CPU frequencies of up to 150 MHz. The ARMCortex-M3 CPU incorporates a 3-stage pipeline and uses a Harvard architecture withseparate local instruction and data buses as well as a third bus for peripherals. The ARMCortex-M3 CPU also includes an internal prefetch unit that supports speculativebranching.The LPC1850/30/20/10 include up to 200 kB of on-chip SRAM data memory, a quad SPIFlash Interface (SPIFI), a State Configuration Timer (SCT) subsystem, two High-speedUSB controllers, Ethernet, LCD, an external memory controller, and multiple digital andanalog peripherals.
上传时间： 2014-12-31
上传用户：zhuoying119
The LPC4350/30/20/10 are ARM Cortex-M4 based microcontrollers for embeddedapplications. The ARM Cortex-M4 is a next generation core that offers systemenhancements such as low power consumption, enhanced debug features, and a highlevel of support block integration.The LPC4350/30/20/10 operate at CPU frequencies of up to 150 MHz. The ARMCortex-M4 CPU incorporates a 3-stage pipeline, uses a Harvard architecture withseparate local instruction and data buses as well as a third bus for peripherals, andincludes an internal prefetch unit that supports speculative branching. The ARMCortex-M4 supports single-cycle digital signal processing and SIMD instructions. Ahardware floating-point processor is integrated in the core.The LPC4350/30/20/10 include an ARM Cortex-M0 coprocessor, up to 264 kB of datamemory, advanced configurable peripherals such as the State Configurable Timer (SCT)and the Serial General Purpose I/O (SGPIO) interface, two High-speed USB controllers,Ethernet, LCD, an external memory controller, and multiple digital and analog peripherals
上传时间： 2013-10-28
上传用户：15501536189
附件有二个文当，都是dxp2004教程 ，第一部份DXP2004的相关快捷键，以及中英文对照的意思。第二部份细致的讲解的如何使用DXP2004。 dxp2004教程第一部份： 目录 1 快捷键 2 常用元件及封装 7 创建自己的集成库 12 板层介绍 14 过孔 15 生成BOM清单 16 顶层原理图: 16 生成PCB 17 包地 18 电路板设计规则 18 PCB设计注意事项 20 画板心得 22 DRC 规则英文对照 22 一、Error Reporting 中英文对照 22 A ： Violations Associated with buses 有关总线电气错误的各类型（共 12 项） 22 B ：Violations Associated Components 有关元件符号电气错误（共 20 项） 22 C ： violations associated with document 相关的文档电气错误（共 10 项） 23 D ： violations associated with nets 有关网络电气错误（共 19 项） 23 E ： Violations associated with others 有关原理图的各种类型的错误 (3 项 ) 24 二、 Comparator 规则比较 24 A ： Differences associated with components 原理图和 PCB 上有关的不同 ( 共 16 项 ) 24 B ： Differences associated with nets 原理图和 PCB 上有关网络不同（共 6 项） 25 C ： Differences associated with parameters 原理图和 PCB 上有关的参数不同（共 3 项） 25 Violations Associated withbuses栏 —总线电气错误类型 25 Violations Associated with Components栏 ——元件电气错误类型 26 Violations Associated with documents栏 —文档电气连接错误类型 27 Violations Associated with Nets栏 ——网络电气连接错误类型 27 Violations Associated with Parameters栏 ——参数错误类型 28 dxp2004教程第二部份 路设计自动化（ Electronic Design Automation ） EDA 指的就是将电路设计中各种工作交由计算机来协助完成。如电路图（ Schematic ）的绘制，印刷电路板（ PCB ）文件的制作执行电路仿真（ Simulation ）等设计工作。随着电子工业的发展，大规模、超大规模集成电路的使用是电路板走线愈加精密和复杂。电子线路 CAD 软件产生了， Protel 是突出的代表，它操作简单、易学易用、功能强大。 1.1 Protel 的产生及发展 1985 年 诞生 dos 版 Protel 1991 年 Protel for Widows 1998 年 Protel98 这个 32 位产品是第一个包含 5 个核心模块的 EDA 工具 1999 年 Protel99 既有原理图的逻辑功能验证的混合信号仿真，又有了 PCB 信号完整性 分析的板级仿真，构成从电路设计到真实板分析的完整体系。 2000 年 Protel99se 性能进一步提高，可以对设计过程有更大控制力。 2002 年 Protel DXP 集成了更多工具，使用方便，功能更强大。 1.2 Protel DXP 主要特点 1 、通过设计档包的方式，将原理图编辑、电路仿真、 PCB 设计及打印这些功能有机地结合在一起，提供了一个集成开发环境。 2 、提供了混合电路仿真功能，为设计实验原理图电路中某些功能模块的正确与否提供了方便。 3 、提供了丰富的原理图组件库和 PCB 封装库，并且为设计新的器件提供了封装向导程序，简化了封装设计过程。 4 、提供了层次原理图设计方法，支持“自上向下”的设计思想，使大型电路设计的工作组开发方式成为可能。 5 、提供了强大的查错功能。原理图中的 ERC （电气法则检查）工具和 PCB 的 DRC （设计规则检查）工具能帮助设计者更快地查出和改正错误。 6 、全面兼容 Protel 系列以前版本的设计文件，并提供了 OrCAD 格式文件的转换功能。 7 、提供了全新的 FPGA 设计的功能，这好似以前的版本所没有提供的功能。
上传时间： 2015-01-01
上传用户：zhyfjj
目录 目录 1 快捷键 2 常用元件及封装 7 创建自己的集成库 12 板层介绍 14 过孔 15 生成BOM清单 16 顶层原理图: 16 生成PCB 17 包地 18 电路板设计规则 18 PCB设计注意事项 20 画板心得 22 DRC 规则英文对照 22 一、Error Reporting 中英文对照 22 A ： Violations Associated with buses 有关总线电气错误的各类型（共 12 项） 22 B ：Violations Associated Components 有关元件符号电气错误（共 20 项） 22 C ： violations associated with document 相关的文档电气错误（共 10 项） 23 D ： violations associated with nets 有关网络电气错误（共 19 项） 23 E ： Violations associated with others 有关原理图的各种类型的错误 (3 项 ) 24 二、 Comparator 规则比较 24 A ： Differences associated with components 原理图和 PCB 上有关的不同 ( 共 16 项 ) 24 B ： Differences associated with nets 原理图和 PCB 上有关网络不同（共 6 项） 25 C ： Differences associated with parameters 原理图和 PCB 上有关的参数不同（共 3 项） 25 Violations Associated withbuses栏 —总线电气错误类型 25 Violations Associated with Components栏 ——元件电气错误类型 26 Violations Associated with documents栏 —文档电气连接错误类型 27 Violations Associated with Nets栏 ——网络电气连接错误类型 27 Violations Associated with Parameters栏 ——参数错误类型 28
上传时间： 2013-11-21
上传用户：旭521
Today’s digital systems combine a myriad of chips with different voltage configurations.Designers must interface 2.5V processors with 3.3V memories—both RAM and ROM—as wellas 5V buses and multiple peripheral chips. Each chip has specific power supply needs. CPLDsare ideal for handling the multi-voltage interfacing, but do require forethought to ensure correctoperation.
上传时间： 2013-11-10
上传用户：yy_cn
