using gpio of 2812 This program requires the DSP281x V1.00 header files. As supplied, this project is configured for "boot to H0" operation.
标签： requires supplied program project
上传时间： 2013-12-21
上传用户：Andy123456
The W78E58B is an 8-bit microcontroller which has an in-system programmable Flash EPROM for firmware updating. The instruction set of the W78E58B is fully compatible with the standard 8052. The W78E58B contains a 32K bytes of main ROM and a 4K bytes of auxiliary ROM which allows the contents of the 32KB main ROM to be updated by the loader program located at the 4KB auxiliary ROM 512 bytes of on-chip RAM four 8-bit bi-directional and bit-addressable I/O ports an additional 4- bit port P4 three 16-bit timer/counters a serial port. These peripherals are supported by a eight sources two-level interrupt capability. To facilitate programming and verification, the ROM inside the W78E58B allows the program memory to be programmed and read electronically. Once the code is confirmed, the user can protect the code for security
标签： microcontroller programmable in-system W78E58B
上传时间： 2017-04-27
上传用户：yiwen213
Want to try a copy of Linux 2.6.29-rc5 in progess with Angstom and Opie? Opie probably isn t good for much but testing but it is kind of fun. This has a very slow boot, which is much improved since this NAND image was made. NAND image of Linux 2.6.9-rc5 with Angstrom and Opie for test. Download file. Set to NOR and power on. Install using the vivi command "Restore NAND Flash from HOST thru USB" Turn off, set to NAND, turn on. Enjoy.
标签： Opie probably Angstom progess
上传时间： 2013-12-17
上传用户：gaojiao1999
dm642通过网络接收烧写文件，然后烧写到flash当中，无需flashburn。此工程是从dm642_5a中copy过来的，加上了boot代码，为的是生成hex文件，烧在flash中，可以独立的运行。
上传时间： 2013-12-10
上传用户：JasonC
基于LPC2478硬件平台的IAP和远程WEB应用。 系统共分为三个部分，BOOT区，LOW区和HIGH区。可通过WEB实现对芯片的远程IAP在线升级.
上传时间： 2017-06-28
上传用户：huannan88
Introduction to Kernel Extension Concepts 1:Hello Kernel: Creating a Kernel Extension With Xcode 2:Hello I/O Kit: Creating a Device Driver With Xcode 3:Hello Debugger: Debugging a Device Driver With GDB 4:Packaging Your KEXT for Distribution and Installation 5:Loading Kernel Extensions at Boot Time 6:Kernel Extension Dependencies 7：Kernel Extension Ownership and Permissions
标签： Kernel Extension Introduction Concepts
上传时间： 2013-12-31
上传用户：tuilp1a
This program requires the DSP2833x header files. // // This program requires an external I2C RTC connected to // the I2C bus at address 0x6f. // // As supplied, this project is configured for "boot to SARAM" // operation. The 2833x Boot Mode table is shown below. // For information on configuring the boot mode of an eZdsp, // please refer to the documentation included with the eZdsp,
标签： requires program This external
上传时间： 2017-07-12
上传用户：dianxin61
This program requires the DSP2833x header files. // // As supplied, this project is configured for "boot to SARAM" // operation. The 2833x Boot Mode table is shown below. // For information on configuring the boot mode of an eZdsp, // please refer to the documentation included with the eZdsp,
标签： configured requires supplied program
上传时间： 2014-01-10
上传用户：lixinxiang
广嵌GEC2410开发板实验程序及PDF文档 GEC2410实战手册目录 一、基本接口实验 1.1 ARM汇编指令编程实验 1.2 Thumb和ARM指令混合编程实验 1.3 C和ARM汇编混合编程实验 1.4 C编程实现LED控制实验 1.5 ARM启动及工作模式切换实验 1.6 外部中断应用实验 1.7 看门狗定时器应用实验 1.8 PWM控制蜂鸣器实验 1.9 实时时钟及闹钟设计实验 1.10 Nor flash 应用实验 1.11 Nand flash 应用实验 二、人机接口实验 2.1 矩阵键盘扫描实验 2.2 ADC模数转换实验 2.3 TFT液晶屏显示实验 2.4 触摸屏控制实验 2.5 汉字字符显示实验 2.6 SD卡应用实验 三、通信接口实验 3.1 串口通信应用实验 3.2 红外模块控制实验 3.3 IIC 总线应用实验 3.4 TFTP以太网通讯实验 3.5 USB device 实验 3.6 IIS音频接口实验. 四、实时操作系统实验 4.1 U－boot在GEC2410上的移植 4.2 嵌入式linux内核移植实现 4.3 uC/OS-II在GEC2410上的移植 4.4 uC/OS-II应用程序设计 4.5 WinCE的BSP设计及hello world实现 4.6 Nucleus PLUS 在GEC2410上的移植 4.7 Nucleus PLUS应用程序设计 共30个实验
上传时间： 2014-01-27
上传用户：懒龙1988
Commented (pt-br) source code of Joshi, one of the first viruses that infect executable files instead of boot sectors.
标签： executable Commented viruses infect
上传时间： 2014-01-12
上传用户：wanghui2438
