Abstract: This application note describes how to design boost converters using the MAX17597 peakcurrent-mode controller. boost converters can be operated in discontinuous conduction mode (DCM) orcontinuous conduction mode (CCM). This operating mode can affect the component choices, stress levelin power devices, and controller design. Formulas for calculating component values and ratingsare alsopresented.
上传时间： 2013-11-16
上传用户：zcs023047
Integrated EMI/Thermal Design forSwitching Power SuppliesWei ZhangThesis submitted to the Faculty of theVirginia Polytechnic Institute and State Universityin partial fulfillment of the requirements for the degree of Integrated EMI/Thermal Design forSwitching Power SuppliesWei Zhang(ABSTRACT)This work presents the modeling and analysis of EMI and thermal performancefor switch power supply by using the CAD tools. The methodology and design guidelinesare developed.By using a boost PFC circuit as an example, an equivalent circuit model is builtfor EMI noise prediction and analysis. The parasitic elements of circuit layout andcomponents are extracted analytically or by using CAD tools. Based on the model, circuitlayout and magnetic component design are modified to minimize circuit EMI. EMI filtercan be designed at an early stage without prototype implementation.In the second part, thermal analyses are conducted for the circuit by using thesoftware Flotherm, which includes the mechanism of conduction, convection andradiation. Thermal models are built for the components. Thermal performance of thecircuit and the temperature profile of components are predicted. Improved thermalmanagement and winding arrangement are investigated to reduce temperature.In the third part, several circuit layouts and inductor design examples are checkedfrom both the EMI and thermal point of view. Insightful information is obtained.
上传时间： 2013-11-10
上传用户：1595690
介绍了独立太阳能光伏发电的意义，采用非隔离型boost/Buck拓扑结构为主电路拓扑，重点分析了主电路的工作原理。设计了基于TMS320LF2812的控制系统硬件电路、控制系统软件及数字PID控制器，给出了基于数字化控制的双向DC-DC变换器的充放电试验、升降压快速切换试验及其技术参数。数字化控制双向DC-DC变换器实现了太阳能板、蓄电池二者之间的稳定充放电及其快速切换。
上传时间： 2014-12-24
上传用户：arnold
，。。。。
上传时间： 2013-11-25
上传用户：hongmo
滑模
上传时间： 2013-10-09
上传用户：wch1989
滑模控制技术
标签： Buck-boost 逆变器 离散 滑模控制
上传时间： 2013-11-11
上传用户：zhengzg
boost LED drivers are often used to drive LEDs in series. If an LED fails while open,overvoltage protection (OVP) is necessary to avoid the damage to a boost integrated circuit (IC) or output capacitor. This application report presents the solutions to increase the TPS61043 LED driver OVP threshold.
标签： Overvoltage Protection Solutions Driver
上传时间： 2013-10-14
上传用户：jiangfire
针对开关电源中的整流电路和其本身的非线性负载特性产生大量谐波污染公共电网问题，提出了一种高功率因素校正电路。采用英飞凌（Infineon）公司的CCM控制模式功率因素校正芯片ICE2PCS01控制驱动MOSFET开关管，并与升压电感、输出电容等组成boost拓扑结构，输入电流与基准电流比较后的误差电流经过放大，再与PWM波比较，得到开关管驱动信号，快速而精确地使输入电流平均值与输入整流电压同相位，接近正弦波。结果表明，该电路方案能大大减小输入电流的谐波分量，在AC176V-264V的宽电压输入范围内得到稳定的DC380V输出，功率因素高达0.98。
上传时间： 2014-01-25
上传用户：13517191407
普通的PWM变换器具有结构简洁、控制简单、频率恒定、输出特性好等优点，故广泛应用于社会生活的各个领域中。本文以boost基本电路为基础，采用简单的无源谐振网络，设计实现了开关管的软开关。这种新型的无源软开关解决了输出二极管反向恢复问题，具有结构简单、高频率、高效率、易于控制等优点。该设计可用于以IGBT为开关器件的高压场合。分析了该变换器的工作原理、实现条件、设计谐振网络的参数、并进行了仿真。
上传时间： 2014-12-24
上传用户：ginani
Abstract: The DS1875 features a pulse-width modulation (PWM) controller that can be used to control aDC-DC converter. The DC-DC converter can then be used to generate the high bias voltages necessaryfor avalanche photodiodes (APDs). This application note describes the operation of a boost converterthat uses the DS1875. Discussion covers the selection of the inductor and switching frequency, and theselection of components that improve the efficiency of the converter. Test data are presented.
上传时间： 2013-10-26
上传用户：lyson
