Abstract: For many first-time users, finding the right logger that meets their needs can be a challenging task. In simple
上传时间： 2014-01-19
上传用户：缥缈
Abstract: A laser module designer can use a fixed resistor, mechanical pot, digital pot, or a digital-to-analogconverter (DAC) to control the laser driver's modulation and bias currents. The advantages of a programmablemethod (POT or DAC) are that the manufacturing process can be automated and digital control can be applied(e.g., to compensate for temperature). Using POTs can be a more simple approach than a DAC. There can be aslight cost advantage to using a POT, but this is usually not significant relative to other pieces of the design.Using a DAC can offer advantages, including improved linearity (translating to ease of software implementationand ability to hit the required accuracy), increased board density, a wider range of resolutions, a betteroptimization range, ease of use with a negative voltage laser driver, and unit-to-unit consistency
上传时间： 2013-11-13
上传用户：ca05991270
Abstract: As electronic systems take over many of the mechanical functions in a car—ranging from engine timing to steering andbraking—there is a growing concern about fault tolerance. There should not be a single point of failure that would prevent a car fromat least "limping" off the road or making it to the nearest service station. Redundant systems, watchdog timers, and other controlcircuits are used to reroute signals and perform other functions that ensure that a vehicle can safely make it off the road when afailure occurs.
上传时间： 2013-11-10
上传用户：diets
IntroductionAs chip designers pack more functions into ICs,pin counts continue to grow and the space betweenpins keeps shrinking. Pin spacings of 0.5 mm and0.65 mm are not at all uncommon. The power ofthese new ICs is wonderful, to be sure, but trou-bleshooting them can be a chore because connect-ing scopes and logic analyzers has become muchmore difficult and less dependable.
标签： Agilent Probing Wedge High
上传时间： 2013-10-22
上传用户：蒋清华嗯
Internal Interrupts are used to respond to asynchronous requests from a certain part of themicrocontroller that needs to be serviced. Each peripheral in the TriCore as well as theBus Control Unit, the Debug Unit, the Peripheral Control Processor (PCP) and the CPUitself can generate an Interrupt Request.So what is an external Interrupt?An external Interrupt is something alike as the internal Interrupt. The difference is that anexternal Interrupt request is caused by an external event. Normally this would be a pulseon Port0 or Port1, but it can be even a signal from the input buffer of the SSC, indicatingthat a service is requested.The User’s Manual does not explain this aspect in detail so this ApNote will explain themost common form of an external Interrupt request. This ApNote will show that there is aneasy way to react on a pulse on Port0 or Port1 and to create with this impulse an InterruptService Request. Later in the second part of the document, you can find hints on how todebounce impulses to enable the use of a simple switch as the input device.Note: You will find additional information on how to setup the Interrupt System in theApNote “First steps through the TriCore Interrupt System” (AP3222xx)1. It would gobeyond the scope of this document to explain this here, but you will find selfexplanatoryexamples later on.
上传时间： 2013-10-27
上传用户：zhangyigenius
The use of the Wind River VxWorks Real-Time Operating System (RTOS) on Virtex™-4embedded PowerPC™ processors continues to be a popular choice for high performanceFPGA designs. The introduction of the Wind River Workbench design environment has enableda new and easier way for designers to control the configuration of the VxWorks kernel. Thisguide shows the steps required to build and configure a ML403 Embedded DevelopmentPlatform to boot and run the VxWorks RTOS. A VxWorks bootloader is created, programmedinto Flash, and used to boot the design. The concepts presented here can be scaled to anyPowerPC enabled development platform.
上传时间： 2013-10-26
上传用户：agent
Radio frequency (RF) can be a complex subject to navigate, but it does not have to be. If you are just getting started with radios or maybe you cannot find that old reference book about antenna aperture, this guide can help. It is intended to provide a basic understanding of RF technology, as well act as a quick reference for those who “know their stuff” but may be looking to brush up on that one niche term that they never quite understood. This document is also a useful reference for Maxim’s products and data sheets, an index to deeper analysis found in our application notes, and a general reference for all things RF.
上传时间： 2013-10-23
上传用户：685
Radio frequency (RF) can be a complex subject to navigate, but it does not have to be. If you are just getting started with radios or maybe you cannot find that old reference book about antenna aperture, this guide can help. It is intended to provide a basic understanding of RF technology, as well act as a quick reference for those who “know their stuff” but may be looking to brush up on that one niche term that they never quite understood. This document is also a useful reference for Maxim’s products and data sheets, an index to deeper analysis found in our application notes, and a general reference for all things RF.
标签： 无线技术
上传时间： 2013-10-08
上传用户：kinochen
The tar file contains the following files: ptfsf.c: heart of the perfect TFSF code ptfsf.h: header file for same ptfsf-demo.c: FDTD code which demonstrates use of perfect TFSF code. Essentially this program used to generate results shown in the paper ptfsf-file-maker.c: code to generate an incident-field file using the "perfect" incident fields ptfsf-demo-file.c: FDTD code which uses the perfect incident fields stored in a file fdtdgen.h: defines macros used in much of my code Makefile: simple make-file to compile programs Also include are some simple script files to run the programs with reasonable values. The code assumes a two-dimensional computational domain with TMz polarization (i.e., non-zero field Ez, Hx, and Hy). The program is currently written so that the incident field always strikes the lower-left corner of the total-field region first. (If you want a different corner, that should be a fairly simple tweak to the code, but for now you ll have to make that tweak yourself.)
标签： ptfsf following the contains
上传时间： 2013-11-28
上传用户：风之骄子
This the third edition of the Writing Device Drivers articles. The first article helped to simply get you acquainted with device drivers and a simple framework for developing a device driver for NT. The second tutorial attempted to show to use IOCTLs and display what the memory layout of Windows NT is. In this edition, we will go into the idea of contexts and pools. The driver we write today will also be a little more interesting as it will allow two user mode applications to communicate with each other in a simple manner. We will call this the “poor man’s pipes” implementation.
标签： the articles Drivers edition
上传时间： 2014-01-16
上传用户：ommshaggar
