The bootloader is stored in the internal boot ROM memory (system memory) of STM32devices. It is programmed by ST during production. Its main task is to download theapplication program to the internal Flash memory through one of the available serialperipherals (USART, CAN, USB, etc.). A communication protocol is defined for each serialinterface, with a compatible command set and sequences
上传时间： 2014-09-06
上传用户：417313137
NXP Semiconductor designed the LPC2400 microcontrollers around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded Trace. The LPC2400 microcontrollers have 512 kB of on-chip high-speedFlash memory. This Flash memory includes a special 128-bit wide memory interface andaccelerator architecture that enables the CPU to execute sequential instructions fromFlash memory at the maximum 72 MHz system clock rate. This feature is available onlyon the LPC2000 ARM Microcontroller family of products. The LPC2400 can execute both32-bit ARM and 16-bit Thumb instructions. Support for the two Instruction Sets meansEngineers can choose to optimize their application for either performance or code size atthe sub-routine level. When the core executes instructions in Thumb state it can reducecode size by more than 30 % with only a small loss in performance while executinginstructions in ARM state maximizes core performance.
上传时间： 2013-11-15
上传用户：zouxinwang
FeaturesThe following standard features are provided.• Choice of RTOS scheduling policy1. Pre-emptive:Always runs the highest available task. Tasks of identical priorityshare CPU time (fully pre-emptive with round robin time slicing).2. Cooperative:Context switches only occur if a task blocks, or explicitly callstaskYIELD().• Co-routines (light weight tasks that utilise very little RAM).• Message queues• Semaphores [via macros]• Trace visualisation ability (requires more RAM)• Majority of source code common to all supported development tools• Wide range of ports and examples
上传时间： 2013-10-13
上传用户：13162218709
The HCS12X family is the successor to the HCS12family, with many additional features. One new feature isthe increased memory available to the CPU and themethods available to access it. This document focuses onthe improved memory map configuration.
上传时间： 2013-11-13
上传用户：王者A
The PCA9670 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plusfamily.The PCA9670 is a drop-in upgrade for the PCF8574 providing higher Fast-mode Plus(Fm+) I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(200 mA versus 100 mA) that supports having all 25 mA LEDs on at the same time andmore device addresses (64 versus 8) are available to allow many more devices on the buswithout address conflicts.
上传时间： 2013-10-15
上传用户：stella2015
The PCA9672 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plusfamily.The PCA9672 is a drop-in upgrade for the PCF8574 providing higher Fast-mode Plus(Fm+) I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(200 mA versus 100 mA) that supports having all LEDs on at the same time and moredevice addresses (16 versus 8) are available to allow many more devices on the buswithout address conflicts.
上传时间： 2013-10-23
上传用户：jasonheung
The PCA9673 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plusfamily.The PCA9673 is a drop in upgrade for the PCF8575 providing higher Fast-mode Plus(Fm+) I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(400 mA versus 100 mA) that supports having all 25 mA LEDs on at the same time andmore device addresses (16 versus 8) are available to allow many more devices on the buswithout address conflicts.
上传时间： 2013-10-29
上传用户：wkchong
The PCA9674/74A is a drop-in upgrade for the PCF8574/74A providing higher Fast-modePlus I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(200 mA versus 100 mA) that supports having all LEDs on at the same time and moredevice addresses (64 versus 8) are available to allow many more devices on the buswithout address conflicts.
上传时间： 2013-10-22
上传用户：wwwwwen5
The outputs of the PCA9518 are immediately available as soon as there is a voltage present on thesupply >~1V and behave as described above. The power-on reset of the PCA9518A keeps the outputsturned off during power-up and maintains the high impedance of the outputs throughout the power-upcycle. There is an additional built-in delay after power-up that allows the analog circuits to stabilize beforethe part is activated.
标签： Replacement 9518 NXP PCA
上传时间： 2013-10-26
上传用户：13817753084
The TL2575 and TL2575HV represent superior alternatives to popular three-terminal linear regulators. Due totheir high efficiency, the devices significantly reduce the size of the heatsink and, in many cases, no heatsink isrequired. Optimized for use with standard series of inductors available from several different manufacturers, theTL2575 and TL2575HV greatly simplify the design of switch-mode power supplies by requiring a minimaladdition of only four to six external components for operation.
标签： STEP-DOWN SWITCHING SIMPLE 1A
上传时间： 2013-11-20
上传用户：jelenecheung
