A MEMS microphone IC is unique among Analog Devices, Inc., products in that its input is an acoustic pressure wave. For this reason, some specifications included in the data sheets for these parts may not be familiar, or familiar specifications may be applied in unfamiliar ways. This application note explains the specifica-tions and terms found in MEMS microphone data sheets so that the microphone can be appropriately designed into a system.
上传时间： 2013-10-31
上传用户：masochism
Abstract: If sensitive analog systems are run from one supply without the sufficient bypassing to eliminate noise,
上传时间： 2013-11-23
上传用户：qiulin1010
Abstract: This design idea explains how to implement an 8-bit analog-to-digital converter (ADC), using a microcontroller
上传时间： 2013-10-30
上传用户：爱死爱死
Abstract: The DS4830 optical microcontroller's analog-to-digital converter (ADC) offset can change with temperature and gainselection. However, the DS4830 allows users to measure the ADC internal offset. The measured ADC offset is added to the ADCoffset register to nullify the offset error. This application note demonstrates the DS4830's ADC internal offset calibration in theapplication program.
上传时间： 2014-12-23
上传用户：萍水相逢
Abstract: This tutorial discusses methods for digitally adjusting the output voltage of a DC-DC converter. The digital adjustmentmethods are with a digital-to-analog converter (DAC), a trim pot (digital potentiometer), and PWM output of a microprocessor.Each method is assessed and several DACs and digital potentiometers presented.
上传时间： 2013-11-20
上传用户：zycidjl
Abstract: This article discusses application circuits for Maxim force/sense digital-to-analog converters (DACs). Applications include:selectable fixed-gain DAC, programmable gain DAC, photodiode bias control, amperometric sensor control, digitally programmablecurrent source, Kelvin load sensing, temperature sensing, and high current DAC output. A brief description of the various DAC outputconfigurations is also given.
标签： DAC
上传时间： 2013-11-04
上传用户：youmo81
Abstract: Using a DAC and a microprocessor supervisor, the system safety can be improved in industrial controllers, programmablelogiccontrollers (PLC), and data-acquisition systems. The analog output is set to zero-scale (or pin-programmable midscale) when amicroprocessor failure, optocoupler failure, or undervoltage condition occurs. A simple application is shown on how to implement thisfunction.
上传时间： 2013-10-17
上传用户：sjb555
以某高速实时频谱仪为应用背景，论述了5 Gsps采样率的高速数据采集系统的构成和设计要点，着重分析了采集系统的关键部分高速ADC（analog to digital，模数转换器）的设计、系统采样时钟设计、模数混合信号完整性设计、电磁兼容性设计和基于总线和接口标准（PCI Express）的数据传输和处理软件设计。在实现了系统硬件的基础上，采用Xilinx公司ISE软件的在线逻辑分析仪（ChipScope Pro）测试了ADC和采样时钟的性能，实测表明整体指标达到设计要求。给出上位机对采集数据进行处理的结果，表明系统实现了数据的实时采集存储功能。
上传时间： 2014-11-26
上传用户：黄蛋的蛋黄
Precision 16-bit analog outputs with softwareconfigurableoutput ranges are often needed in industrialprocess control equipment, analytical and scientificinstruments and automatic test equipment. In the past,designing a universal output module was a daunting taskand the cost and PCB real estate associated with thisfunction were problematic, if not prohibitive.
上传时间： 2014-12-23
上传用户：如果你也听说
High input impedance and a wide input range are twohighly desirable features in a precision analog-to-digitalconverter, and the LTC®2449 delta-sigma ADC has both.With just a few external components, the LTC2449 formsan exceptional measurement system with very high inputimpedance and an input range that extends 300mV beyondthe supply rails.
上传时间： 2013-11-02
上传用户：ywcftc277
