nesc language introduction. nesC is an extension to C [2] designed to embody the structuring concepts and execution model of TinyOS [1]. TinyOS is an event-driven operating system designed for sensor network nodes that have very limited resources (e.g., 8K bytes of program memory, 512 bytes of RAM). TinyOS has been reimplemented in nesC. This manual describes v1.1 of nesC, changes from v1.0 are summarised in Section 3.
标签： introduction structuring extension language
上传时间： 2017-09-04
上传用户：66666
To use this function just define a variable say var, var = pnseq(a, b, c) for a, b and c refer to the zip file
标签： var function variable define
上传时间： 2014-01-06
上传用户：zhuoying119
AN INTRODUCTION TO MATHEMATICAL. optimal control.
标签： INTRODUCTION MATHEMATICAL optimal control
上传时间： 2017-09-12
上传用户：GHF
An e-book on wireless ad-hoc and sensor networks introduction to protocols and platforms
标签： introduction and protocols platforms
上传时间： 2017-09-12
上传用户：wkchong
针对目前使用的RS232接口数字化B超键盘存在PC主机启动时不能设置BIOS，提出一种PS2键盘的设计方法。基于W78E052D单片机，采用8通道串行A/D转换器设计了8个TGC电位器信息采集电路，电位器位置信息以键盘扫描码序列形式发送，正交编码器信号通过XC9536XL转换为单片机可接收的中断信号，软件接收到中断信息后等效处理成按键。结果表明，在满足开机可设置BIOS同时，又可实现超声特有功能，不需要专门设计驱动程序，接口简单，成本低。 Abstract: Aiming at the problem of the digital ultrasonic diagnostic imaging system keyboard with RS232 interface currently used couldn?蒺t set the BIOS when the PC boot， this paper proposed a design method of PS2 keyboards. Based on W78E052D microcontroller，designed eight TGC potentiometers information acquisition circuit with 8-channel serial A/D converter， potentiometer position information sent out with keyboard scan code sequentially.The control circuit based on XC9536 CPLD is used for converting the mechanical actions of the encoders into the signals that can be identified by the MCU， software received interrupt information and equivalently treatmented as key. The results show that the BIOS can be set to meet the boot， ultrasound specific functionality can be achieved at the same time， it does not require specially designed driver，the interface is simple and low cost.
上传时间： 2013-10-10
上传用户：asdfasdfd
The Kannel Open Source WAP and SMS gateway works as both an SMS gateway, for implementing keyword based services via GSM text messages, and a WAP gateway, via UDP. The SMS part is fairly mature, the WAP part is early in its development. In this release, the GET request for WML pages and WMLScript files via HTTP works, including compilation for WML and WMLScript to binary forms. Only the data call bearer (UDP) is supported, not SMS.
标签： gateway implementing SMS keyword
上传时间： 2014-01-11
上传用户：2525775
MFC Black Book Introduction: Are you an MFC programmer? Good. There are two types of MFC programmers. What kind are you? The first kind are the good programmers who write programs that conform to the way MFC wants you to do things. The second bunch are wild-eyed anarchists who insist on getting things done their way. Me, I’m in the second group. If you are in the same boat (or would like to be) this book is for you. This book won’t teach you MFC—not in the traditional sense. You should pick it up with a good understanding of basic MFC programming and a desire to do things differently. This isn’t a Scribble tutorial (although I will review some fundamentals in the first chapter). You will learn how to wring every drop from your MFC programs. You’ll discover how to use, abuse, and abandon the document/view architecture. If you’ve ever wanted custom archives, you’ll find that, too.
标签： MFC Introduction programmer programme
上传时间： 2015-05-30
上传用户：youke111
光学设计软件zemax源码： This DLL models an nular aspheric surface as described in: "Annular surfaces in annular field systems" By Jose M. Sasian Opt. eng. 36 (12) P 3401-3401 December 1997 This surface is essentially an odd aspheric surface with an offset in the aspheric terms. The sag is given by: Z = (c*r*r) / (1+(1-((1+k)*c*c*r*r))^ 1/2 ) + a*(r-q)^2 + b*(r-q)^3 + c*(r-q)^4 + ... Note the terms a, b, c, ... have units of length to the -1, -2, -3, ... power.
标签： described aspheric surfaces Annular
上传时间： 2014-01-08
上传用户：yyyyyyyyyy
Implemented BFS, DFS and A* To compile this project, use the following command: g++ -o search main.cpp Then you can run it: ./search The input is loaded from a input file in.txt Here is the format of the input file: The first line of the input file shoud contain two chars indicate the source and destination city for breadth first and depth first algorithm. The second line of input file shoud be an integer m indicate the number of connections for the map. Following m lines describe the map, each line represents to one connection in this form: dist city1 city2, which means there is a connection between city1 and city2 with the distance dist. The following input are for A* The following line contains two chars indicate the source and destination city for A* algorithm. Then there is an integer h indicate the number of heuristic. The following h lines is in the form: city dist which means the straight-line distance from the city to B is dist.
标签： Implemented following compile command
上传时间： 2014-01-01
上传用户：lhc9102
* "Copyright (c) 2006 Robert B. Reese ("AUTHOR")" * All rights reserved. * (R. Reese, reese@ece.msstate.edu, Mississippi State University) * IN NO EVENT SHALL THE "AUTHOR" BE LIABLE TO ANY PARTY FOR * DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING OUT * OF THE USE OF THIS SOFTWARE AND ITS DOCUMENTATION, EVEN IF THE "AUTHOR" * HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
上传时间： 2015-09-24
上传用户：mpquest
