addr

移植uip-1.0到Atmega32 1）把 uip-1.0 的所有文件加入到工程

移植uip-1.0到Atmega32 1）把 uip-1.0 的所有文件加入到工程，包括 uip 目录的文件（除uip-split.c）、unix 目录的文件、lib 目录的文件； 2）修改 uip/uip-neighbor.c 文件的 void uip_neighbor_add(uip_ipaddr_t ipaddr, struct uip_neighbor_addr *addr) 函数，一般注释掉 printf 语句即可，或者改为你自己的串口格式化打印实现。 3）uip 目录里的源文件除 uipopt.h 外一般都无需修改；uipopt.h 包含了 uip-conf.h ，所以大部分修改可以在 uip-conf.h 里进行。 uip-conf.h 里加入如下定义，可以减少编译的警告： #define notdef 0 #define UIP_CONF_IPV6 0 #define UIP_ARCH_ADD32 0 #define UIP_ARCH_CHKSUM 0 #define UIP_NEIGHBOR_CONF_addrTYPE 0 4）移植工作主要是定时器中断程序与网络驱动的编写

标签： uip 1.0 Atmega 32

上传时间： 2013-12-20

上传用户：csgcd001
红外遥控RGB

#include "STC90.h" #include < intrins.h > #define uchar unsigned char #define uint unsigned int #define led_port P1 sbit IR_RE = P3^2; sbit led_r = P1^3; sbit led_g = P1^4; sbit led_b = P1^5; sbit led_wd = P1^7; sbit K1 =P3^0 ; //增加键 sbit K2 =P3^1 ; //减少键 sbit BEEP =P3^7 ; //蜂鸣器 uchar temp,temp1; bit k=0; //红外解码判断标志位，为0则为有效信号，为1则为无效 bit Flag2; uchar date[4]={0,0,0,0}; //date数组为存放地址原码，反码，数据原码，反码 uint lade_1,lade_2,lade_3,lade_4; uint num; uchar date_ram,ee_temp,ee_temp1; uchar WDT_NUM=0; uchar const dofly[]={0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f};// 显示段码值01234567 uchar code seg[]={7,6,5,4,3,2,1,0};//分别对应相应的数码管点亮,即位码 unsigned long disp_date; void fade(); void fade1(); /*************************** 看门狗子程序*************************/ void watchdog_timer() { if(WDT_NUM==5) { WDT_NUM=0; led_wd=!led_wd; } WDT_NUM++; WDT_CONTR=0x3f; } /******************************************************************/ void delay(unsigned int cnt) { while(--cnt); } /*--------------------------延时1ms程子程序-----------------------*/ void delay_1ms(uint z) { uint x,y; for(x=z;x>0;x--) for(y=126;y>0;y--); } /*--------------------------延时1ms程子程序-----------------------*/ delay1000() { uchar i,j; i=5; do{j=95; do{j--;} while(j); i--; } while(i); } /*---------------------------延时882us子程序-----------------------*/ delay882() { uchar i,j; i=6; do{j=71; do{j--;} while(j); i--; }while(i); } /*--------------------------延时2400us程子程序-----------------------*/ delay2400() { uchar i,j; i=5; do{j=237; do{j--;} while(j); i--; }while(i); } /**********************************************************************/ /* void display() { uchar i; for(i=0;i<8;i++) { P0=dofly[disp_date%10];//取显示数据，段码 P2=seg[i]; //取位码 delay_1ms(1); disp_date/=10; } } */ /*********************************************************************/ uchar EEPROM_read(uint addr)//EEPROM字节读 { ISP_CONTR=0x83; //系统时钟<12M时，对ISP_CONTR寄存器设置的值，本电路为11.0592M ISP_CMD=1; //字节读 ISP_addrH=(addr&0xff00)>>8; ISP_addrL=addr&0x00ff; ISP_TRIG=0x46; ISP_TRIG=0xb9; _nop_(); _nop_(); return ISP_DATA; } //-------------------------------------------------------------------- void EEPROM_write(uint addr,uchar dat)//EEPROM字节写 { ISP_CONTR=0x83; //系统时钟<12M时，对ISP_CONTR寄存器设置的值，本电路为11.0592M ISP_CMD=2; //字节编程 ISP_addrH=(addr&0xff00)>>8; ISP_addrL=addr&0x00ff; ISP_DATA=dat; ISP_TRIG=0x46; ISP_TRIG=0xb9; _nop_(); _nop_(); } //-------------------------------------------------------------------- void EEPROM_ERASE(uint addr)//EEPROM扇区擦除 { ISP_CONTR=0x83; //系统时钟<12M时，对ISP_CONTR寄存器设置的值，本电路为11.0592M ISP_CMD=3; //扇区擦除 ISP_addrH=(addr&0xff00)>>8; ISP_addrL=addr&0x00ff; ISP_TRIG=0x46; ISP_TRIG=0xb9; _nop_(); _nop_(); } //************************************************************** /*----------------------------------------------------------*/ /*-----------------------红外解码程序(核心)-----------------*/ /*----------------------------------------------------------*/ void IR_decode() { uchar i,j; while(IR_RE==0); delay2400(); if(IR_RE==1) //延时2.4ms后如果是高电平则是新码 { delay1000(); delay1000(); for(i=0;i<4;i++) { for(j=0;j<8;j++) { while(IR_RE==0); //等待地址码第1位高电平到来 delay882(); //延时882us判断此时引脚电平 ///CY=IR_RE; if(IR_RE==0) { date[i]>>=1; date[i]=date[i]|0x00; } else if(IR_RE==1) { delay1000(); date[i]>>=1; date[i]=date[i]|0x80; } } //1位数据接收结束 } //32位二进制码接收结束 } } /* void LED_PWM() { lade_2=num; //384 lade_4=num; //384 while(lade_2!=0&Flag2==1) { for(lade_3=512;lade_3>lade_4;lade_3--) //512 { led_port=0x00; delay(1); } lade_3=512; //512 lade_4--; for(lade_1=0;lade_1<lade_2;lade_1++) { led_port=0x38; //c7 delay(1); } lade_1=0; lade_2--; if(temp!=0x0c&Flag2==1) { lade_2=0; } lade_2=num; //384 lade_4=num; //384 } } */ void calc() { EEPROM_read(0x2000); ee_temp1=ISP_DATA; ee_temp=ee_temp1&0x0f; //************************************* 1 /* if(date[3]==0xff&Flag2==1) { if(num>=20) { num=num-80; } //else num=1; LED_PWM(); } if(date[3]==0xfe&Flag2==1) { if(num<=500) { num=num+80; } // else num=511; LED_PWM(); } if(ee_temp1==0xfd) { led_port=0x00; watchdog_timer(); } if(ee_temp1==0xfc) { led_port=0x00; led_r=1; led_g=1; led_b=1; watchdog_timer(); } */ //********************************************** 2 if(ee_temp1==0xfb) { led_port=0x00; led_r=1; watchdog_timer(); } if(ee_temp1==0xfa) { led_port=0x00; led_g=1; watchdog_timer(); } if(ee_temp1==0xf9) { led_port=0x00; led_b=1; watchdog_timer(); } if(ee_temp1==0xf8) { led_port=0x00; led_r=1; led_g=1; led_b=1; watchdog_timer(); } //************************************** 3 if(ee_temp1==0xf7) { uint fade_1,fade_2,fade_3,fade_4; fade_2=448; //384 fade_4=448; //384 while(fade_2!=0&ee_temp==0x07) { for(fade_3=512;fade_3>fade_4;fade_3--) //512 { led_port=0x10; delay(1); } fade_3=512; //512 fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x08; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x07) { fade_2=0; } watchdog_timer(); fade_2=448; //384 fade_4=448; //384 } } if(ee_temp1==0xf6) { uint fade_1,fade_2,fade_3,fade_4; fade_2=448; //384 fade_4=448; //384 while(fade_2!=0&ee_temp==0x06) { for(fade_3=512;fade_3>fade_4;fade_3--) //512 { led_port=0x20; delay(1); } fade_3=512; //512 fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x10; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x06) { fade_2=0; } watchdog_timer(); fade_2=448; //384 fade_4=448; //384 } } if(ee_temp1==0xf5) { uint fade_1,fade_2,fade_3,fade_4; fade_2=448; //384 fade_4=448; //384 while(fade_2!=0&ee_temp==0x05) { for(fade_3=512;fade_3>fade_4;fade_3--) //512 { led_port=0x08; delay(1); } fade_3=512; //512 fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x20; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x05) { fade_2=0; } watchdog_timer(); fade_2=448; //384 fade_4=448; //384 } } if(ee_temp1==0xf4) { while(ee_temp==4) { led_port=0x00; led_r=1; delay_1ms(200); led_port=0x00; led_r=1; led_g=1; delay_1ms(200); led_port=0x00; led_g=1; delay_1ms(200); watchdog_timer(); led_port=0x00; led_g=1; led_b=1; delay_1ms(200); led_port=0x00; led_b=1; delay_1ms(200); led_port=0x00; led_b=1; led_r=1; delay_1ms(200); watchdog_timer(); } } //************************************** 4 if(ee_temp1==0xf3) { uint fade_1,fade_2,fade_3,fade_4; fade_2=416; //384 fade_4=416; //384 while(fade_2!=0&ee_temp==0x03) { for(fade_3=512;fade_3>fade_4;fade_3--) //512 { led_port=0x10; delay(1); } fade_3=512; //512 fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x08; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x03) { fade_2=0; } watchdog_timer(); fade_2=416; //384 fade_4=416; //384 } } if(ee_temp1==0xf2) { uint fade_1,fade_2,fade_3,fade_4; fade_2=384; //384 fade_4=384; //384 while(fade_2!=0&ee_temp==0x02) { for(fade_3=512;fade_3>fade_4;fade_3--) //512 { led_port=0x20; delay(1); } fade_3=512; //512 fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x10; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x02) { fade_2=0; } watchdog_timer(); fade_2=384; //384 fade_4=384; //384 } } if(ee_temp1==0xf1) { uint fade_1,fade_2,fade_3,fade_4; fade_2=348; //384 fade_4=348; //384 while(fade_2!=0&ee_temp==0x01) { for(fade_3=512;fade_3>fade_4;fade_3--) //512 { led_port=0x08; delay(1); } fade_3=512; //512 fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x20; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x01) { fade_2=0; } watchdog_timer(); fade_2=348; //384 fade_4=348; //384 } } if(ee_temp1==0xf0) { while(ee_temp==0) { led_port=0x00; led_r=1; delay_1ms(500); watchdog_timer(); led_port=0x00; led_g=1; delay_1ms(500); led_port=0x00; led_b=1; delay_1ms(500); watchdog_timer(); } } //******************************************** 5 if(ee_temp1==0xef) { uint fade_1,fade_2,fade_3,fade_4; fade_2=384; //384 fade_4=384; //384 while(fade_2!=0&ee_temp==0x0f) { for(fade_3=512;fade_3>fade_4;fade_3--) //512 { led_port=0x10; delay(1); } fade_3=512; //512 fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x08; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x0f) { fade_2=0; } watchdog_timer(); fade_2=384; //384 fade_4=384; //384 } } if(ee_temp1==0xee) { uint fade_1,fade_2,fade_3,fade_4; fade_2=320; //384 fade_4=320; //384 while(fade_2!=0&ee_temp==0x0e) { for(fade_3=512;fade_3>fade_4;fade_3--) //512 { led_port=0x20; delay(1); } fade_3=512; //512 fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x10; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x0e) { fade_2=0; } watchdog_timer(); fade_2=320; //384 fade_4=320; //384 } } if(ee_temp1==0xed) { uint fade_1,fade_2,fade_3,fade_4; fade_2=320; //384 fade_4=320; //384 while(fade_2!=0&ee_temp==0x0d) { for(fade_3=512;fade_3>fade_4;fade_3--) //512 { led_port=0x08; delay(1); } fade_3=512; //512 fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x20; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x0d) { fade_2=0; } watchdog_timer(); fade_2=320; //384 fade_4=320; //384 } } if(ee_temp1==0xec) fade(); //******************************************* 6 if(ee_temp1==0xeb) { led_port=0x00; led_r=1; led_g=1; watchdog_timer(); } if(ee_temp1==0xea) { led_port=0x00; //led_r=0; led_g=1; led_b=1; watchdog_timer(); } if(ee_temp1==0xe9) { led_port=0x00; led_r=1; //led_g=0; led_b=1; watchdog_timer(); } if(ee_temp1==0xe8) fade1(); } void fade() { // uchar i; uint fade_1,fade_2,fade_3,fade_4; fade_2=512; fade_4=511; while(fade_2!=0&ee_temp==0x0c) { for(fade_3=512;fade_3>fade_4;fade_3--) { led_port=0x10; delay(1); } fade_3=512; fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x08; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x0c) { fade_2=0; } } watchdog_timer(); fade_2=512; fade_4=511; while(fade_2!=0&ee_temp==0x0c) { if(ee_temp!=0x0c) { fade_2=0; } for(fade_3=512;fade_3>fade_4;fade_3--) { led_port=0x20; delay(1); // watchdog_timer(); } fade_3=512; fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x10; delay(1); // watchdog_timer(); } fade_1=0; fade_2--; } watchdog_timer(); fade_2=512; fade_4=511; while(fade_2!=0&ee_temp==0x0c) { if(ee_temp!=0x0c) { fade_2=0; } for(fade_3=512;fade_3>fade_4;fade_3--) { led_port=0x08; delay(1); watchdog_timer(); } fade_3=512; fade_4--; watchdog_timer(); for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x20; delay(1); watchdog_timer(); } fade_1=0; fade_2--; } watchdog_timer(); } void fade1() { // uchar i; uint fade_1,fade_2,fade_3,fade_4; fade_2=128; fade_4=127; while(fade_2!=0&ee_temp==0x08) { for(fade_3=128;fade_3>fade_4;fade_3--) { led_port=0x10; delay(1); } fade_3=128; fade_4--; for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x08; delay(1); } fade_1=0; fade_2--; if(ee_temp!=0x08) { fade_2=0; } } watchdog_timer(); fade_2=128; fade_4=127; while(fade_2!=0&ee_temp==0x08) { if(ee_temp!=0x08) { fade_2=0; } for(fade_3=128;fade_3>fade_4;fade_3--) { led_port=0x20; delay(1); } fade_3=128; fade_4--; for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x10; delay(1); } fade_1=0; fade_2--; } watchdog_timer(); fade_2=128; fade_4=127; while(fade_2!=0&ee_temp==0x08) { if(ee_temp!=0x08) { fade_2=0; } for(fade_3=128;fade_3>fade_4;fade_3--) { led_port=0x08; delay(1); } fade_3=128; fade_4--; for(fade_1=0;fade_1<fade_2;fade_1++) { led_port=0x20; delay(1); } fade_1=0; fade_2--; } watchdog_timer(); } void init() { led_port=0x00; /* led_r=1; delay_1ms(500); led_port=0x00; led_g=1; delay_1ms(500); led_port=0x00; led_b=1; delay_1ms(500); led_port=0x00; */ delay_1ms(2); WDT_CONTR=0x3f; delay_1ms(500); } //******************************** void main() { init(); Flag2=0; SP=0x60; //堆栈指针 EX0=1; //允许外部中断0,用于检测红外遥控器按键 EA=1; num=255; while(1) { calc(); } } //******************************************************************** /*------------------------外部中断0程序-------------------------*/ /*------------------主要用于处理红外遥控键值--------------------*/ void int0() interrupt 0 { uchar i; Flag2=0; /////// k=0; EX0=0; //检测到有效信号关中断，防止干扰 for(i=0;i<4;i++) { delay1000(); if(IR_RE==1){k=1;} //刚开始为9ms的引导码. } led_port=0x00; if(k==0) { IR_decode(); //如果接收到的是有效信号，则调用解码程序 if(date[3]>=0xe8) { if(date[3]<=0xfb) { temp1=date[3]; EEPROM_ERASE(0x2000); //STC_EEROM_0X2000 temp1 EEPROM_write(0x2000,temp1); EEPROM_read(0x2000); ee_temp1=ISP_DATA; ee_temp=ee_temp1&0x0f; /* temp=date[3]&0x0f; EEPROM_ERASE(0x2004); //STC_EEROM_0X2004 temp EEPROM_write(0x2004,temp); */ } else { EEPROM_read(0x2000); ee_temp1=ISP_DATA; ee_temp=ee_temp1&0x0f; } } delay2400(); delay2400(); delay2400(); delay_1ms(500); } EX0=1; //开外部中断，允许新的遥控按键 }

标签： RGB 红外遥控

上传时间： 2016-07-02

上传用户：184890962
12345

/****************temic*********t5557***********************************/ #include <at892051.h> #include <string.h> #include <intrins.h> #include <stdio.h> #define uchar unsigned char #define uint unsigned int #define ulong unsigned long //STC12C2051AD的SFR定义 sfr WDT_CONTR = 0xe1;//stc2051的看门狗?????? /**********全局常量************/ //写卡的命令 #define write_command0 0//写密码 #define write_command1 1//写配置字 #define write_command2 2//密码写数据 #define write_command3 3//唤醒 #define write_command4 4//停止命令 #define TRUE 1 #define FALSE 0 #define OK 0 #define ERROR 255 //读卡的时间参数us #define ts_min 250//270*11.0592/12=249//取近似的整数 #define ts_max 304//330*11.0592/12=304 #define t1_min 73//90*11.0592/12=83:-10调整 #define t1_max 156//180*11.0592/12=166 #define t2_min 184//210*11.0592/12=194 #define t2_max 267//300*11.0592/12=276 //***********不采用中断处理:采用查询的方法读卡时关所有中断****************/ sbit p_U2270B_Standby = P3^5;//p_U2270B_Standby PIN=13 sbit p_U2270B_CFE = P3^3;//p_U2270B_CFE PIN=6 sbit p_U2270B_OutPut = P3^7;//p_U2270B_OutPut PIN=2 sbit wtd_sck = P1^7;//SPI总线 sbit wtd_si = P1^3; sbit wtd_so = P1^2; sbit iic_data = P1^2;//lcd IIC sbit iic_clk = P1^7; sbit led_light = P1^6;//测试绿灯 sbit led_light1 = P1^5;//测试红灯 sbit led_light_ok = P1^1;//读卡成功标志 sbit fengmingqi = P1^5; /***********全局变量************************************/ uchar data Nkey_a[4] = {0xA0, 0xA1, 0xA2, 0xA3};//初始密码 //uchar idata card_snr[4]; //配置字 uchar data bankdata[28] = {1,2,3,4,5,6,7,1,2,3,4,5,6,7,1,2,3,4,5,6,7,1,2,3,4,5,6,7}; //存储卡上用户数据(1-7)7*4=28 uchar data cominceptbuff[6] = {1,2,3,4,5,6};//串口接收数组ram uchar command; //第一个命令 uchar command1;// //uint temp; uchar j,i; uchar myaddr = 8; //uchar ywqz_count,time_count; //ywqz jishu: uchar bdata DATA; sbit BIT0 = DATA^0; sbit BIT1 = DATA^1; sbit BIT2 = DATA^2; sbit BIT3 = DATA^3; sbit BIT4 = DATA^4; sbit BIT5 = DATA^5; sbit BIT6 = DATA^6; sbit BIT7 = DATA^7; uchar bdata DATA1; sbit BIT10 = DATA1^0; sbit BIT11 = DATA1^1; sbit BIT12 = DATA1^2; sbit BIT13 = DATA1^3; sbit BIT14 = DATA1^4; sbit BIT15 = DATA1^5; sbit BIT16 = DATA1^6; sbit BIT17 = DATA1^7; bit i_CurrentLevel;//i_CurrentLevel BIT 00H(Saves current level of OutPut pin of U2270B) bit timer1_end; bit read_ok = 0; //缓存定时值,因用同一个定时器 union HLint { uint W; struct { uchar H;uchar L; } B; };//union HLint idata a union HLint data a; //缓存定时值,因用同一个定时器 union HLint0 { uint W; struct { uchar H; uchar L; } B; };//union HLint idata a union HLint0 data b; /**********************函数原型*****************/ //读写操作 void f_readcard(void);//全部读出1~7 AOR唤醒 void f_writecard(uchar x);//根据命令写不同的内容和操作 void f_clearpassword(void);//清除密码 void f_changepassword(void);//修改密码 //功能子函数 void write_password(uchar data *data p);//写初始密码或数据 void write_block(uchar x,uchar data *data p);//不能用通用指针 void write_bit(bit x);//写位 /*子函数区*****************************************************/ void delay_2(uint x) //延时,时间x*10us@12mhz,最小20us@12mhz { x--; x--; while(x) { _nop_(); _nop_(); x--; } _nop_();//WDT_CONTR=0X3C;不能频繁的复位 _nop_(); } ///////////////////////////////////////////////////////////////////// void initial(void) { SCON = 0x50; //串口方式1,允许接收 //SCON =0x50; //01010000B:10位异步收发,波特率可变,SM2=0不用接收到有效停止位才RI=1, //REN=1允许接收 TMOD = 0x21; //定时器1 定时方式2(8位),定时器0 定时方式1(16位) TCON = 0x40; //设定时器1 允许开始计时(IT1=1) TH1 = 0xfD; //FB 18.432MHz 9600 波特率 TL1 = 0xfD; //fd 11.0592 9600 IE = 0X90; //EA=ES=1 TR1 = 1; //启动定时器 WDT_CONTR = 0x3c;//使能看门狗 p_U2270B_Standby = 0;//单电源 PCON = 0x00; IP = 0x10;//uart you xian XXXPS PT1 PX1 PT0 PX0 led_light1 = 1; led_light = 0; p_U2270B_OutPut = 1; } /************************************************/ void f_readcard()//读卡 { EA = 0;//全关,防止影响跳变的定时器计时 WDT_CONTR = 0X3C;//喂狗 p_U2270B_CFE = 1;// delay_2(232); //>2.5ms /* // aor 用唤醒功能来防碰撞 p_U2270B_CFE = 0; delay_2(18);//start gap>150us write_bit(1);//10=操作码读0页 write_bit(0); write_password(&bankdata[24]);//密码block7 p_U2270B_CFE =1 ;// delay_2(516);//编程及确认时间5.6ms */ WDT_CONTR = 0X3C;//喂狗 led_light = 0; b.W = 0; while(!(read_ok == 1)) { //while(p_U2270B_OutPut);//等一个稳定的低电平?超时判断? while(!p_U2270B_OutPut);//等待上升沿的到来同步信号检测1 TR0 = 1; //deng xia jiang while(p_U2270B_OutPut);//等待下降沿 TR0 = 0; a.B.H = TH0; a.B.L = TL0; TH0 = TL0 = 0; TR0 = 1;//定时器晚启动10个周期 //同步头 if((324 < a.W) && (a.W < 353)) ;//检测同步信号1 else { TR0 = 0; TH0 = TL0 = 0; goto read_error; } //等待上升沿 while(!p_U2270B_OutPut); TR0 = 0; a.B.H = TH0; a.B.L = TL0; TH0 = TL0 = 0; TR0 = 1;//b.N1<<=8; if(a.B.L < 195);//0.5p else { TR0 = 0; TH0 = TL0 = 0; goto read_error; } //读0~7块的数据 for(j = 0;j < 28;j++) { //uchar i; for(i = 0;i < 16;i++)//8个位 { //等待下降沿的到来 while(p_U2270B_OutPut); TR0 = 0; a.B.H = TH0; a.B.L = TL0; TH0 = TL0 = 0; TR0 = 1; if(t2_max < a.W/*)&&(a.W < t2_max)*/)//1P { b.W >>= 2;//先左移再赋值 b.B.L += 0xc0; i++; } else if(t1_min < a.B.L/*)&&(a.B.L < t1_max)*/)//0.5p { b.W >>= 1; b.B.L += 0x80; } else { TR0 = 0; TH0 = TL0 = 0; goto read_error; } i++; while(!p_U2270B_OutPut);//上升 TR0 = 0; a.B.H = TH0; a.B.L = TL0; TH0 = TL0 = 0; TR0 = 1; if(t2_min < a.W/*)&&(a.W < t2_max)*/)//1P { b.W >>= 2; i++; } else if(t1_min < a.B.L/*a.W)&&(a.B.L < t1_max)*/)//0.5P //else if(!(a.W==0)) { b.W >>= 1; //temp+=0x00; //led_light1=0;led_light=1;delay_2(40000); } else { TR0 = 0; TH0 = TL0 = 0; goto read_error; } i++; } //取出奇位 DATA = b.B.L; BIT13 = BIT7; BIT12 = BIT5; BIT11 = BIT3; BIT10 = BIT1; DATA = b.B.H; BIT17 = BIT7; BIT16 = BIT5; BIT15 = BIT3; BIT14 = BIT1; bankdata[j] = DATA1; } read_ok = 1;//读卡完成了 read_error: _nop_(); } } /***************************************************/ void f_writecard(uchar x)//写卡 { p_U2270B_CFE = 1; delay_2(232); //>2.5ms //psw=0 standard write if (x == write_command0)//写密码:初始化密码 { uchar i; uchar data *data p; p = cominceptbuff; p_U2270B_CFE = 0; delay_2(31);//start gap>330us write_bit(1);//写操作码1:10 write_bit(0);//写操作码0 write_bit(0);//写锁定位0 for(i = 0;i < 35;i++) { write_bit(1);//写数据位1 } p_U2270B_CFE = 1; led_light1 = 0; led_light = 1; delay_2(40000);//测试使用 //write_block(cominceptbuff[4],p); p_U2270B_CFE = 1; bankdata[20] = cominceptbuff[0];//密码存入 bankdata[21] = cominceptbuff[1]; bankdata[22] = cominceptbuff[2]; bankdata[23] = cominceptbuff[3]; } else if (x == write_command1)//配置卡参数:初始化 { uchar data *data p; p = cominceptbuff; write_bit(1);//写操作码1:10 write_bit(0);//写操作码0 write_bit(0);//写锁定位0 write_block(cominceptbuff[4],p); p_U2270B_CFE= 1; } //psw=1 pssword mode else if(x == write_command2) //密码写数据 { uchar data*data p; p = &bankdata[24]; write_bit(1);//写操作码1:10 write_bit(0);//写操作码0 write_password(p);//发口令 write_bit(0);//写锁定位0 p = cominceptbuff; write_block(cominceptbuff[4],p);//写数据 } else if(x == write_command3)//aor //唤醒 { //cominceptbuff[1]操作码10 X xxxxxB uchar data *data p; p = cominceptbuff; write_bit(1);//10 write_bit(0); write_password(p);//密码 p_U2270B_CFE = 1;//此时数据不停的循环传出 } else //停止操作码 { write_bit(1);//11 write_bit(1); p_U2270B_CFE = 1; } p_U2270B_CFE = 1; delay_2(560);//5.6ms } /************************************/ void f_clearpassword()//清除密码 { uchar data *data p; uchar i,x; p = &bankdata[24];//原密码 p_U2270B_CFE = 0; delay_2(18);//start gap>150us //操作码10:10xxxxxxB write_bit(1); write_bit(0); for(x = 0;x < 4;x++)//发原密码 { DATA = *(p++); for(i = 0;i < 8;i++) { write_bit(BIT0); DATA >>= 1; } } write_bit(0);//锁定位0:0 p = &cominceptbuff[0]; write_block(0x00,p);//写新配置参数:pwd=0 //密码无效:即清除密码 DATA = 0x00;//停止操作码00000000B for(i = 0;i < 2;i++) { write_bit(BIT7); DATA <<= 1; } p_U2270B_CFE = 1; delay_2(560);//5.6ms } /*********************************/ void f_changepassword()//修改密码 { uchar data *data p; uchar i,x,addr; addr = 0x07;//block7 p = &Nkey_a[0];//原密码 DATA = 0x80;//操作码10:10xxxxxxB for(i = 0;i < 2;i++) { write_bit(BIT7); DATA <<= 1; } for(x = 0;x < 4;x++)//发原密码 { DATA = *(p++); for(i = 0;i < 8;i++) { write_bit(BIT7); DATA >>= 1; } } write_bit(0);//锁定位0:0 p = &cominceptbuff[0]; write_block(0x07,p);//写新密码 p_U2270B_CFE = 1; bankdata[24] = cominceptbuff[0];//密码存入 bankdata[25] = cominceptbuff[1]; bankdata[26] = cominceptbuff[2]; bankdata[27] = cominceptbuff[3]; DATA = 0x00;//停止操作码00000000B for(i = 0;i < 2;i++) { write_bit(BIT7); DATA <<= 1; } p_U2270B_CFE = 1; delay_2(560);//5.6ms } /***************************子函数***********************************/ void write_bit(bit x)//写一位 { if(x) { p_U2270B_CFE = 1; delay_2(32);//448*11.0592/120=42延时448us p_U2270B_CFE = 0; delay_2(28);//280*11.0592/120=26写1 } else { p_U2270B_CFE = 1; delay_2(92);//192*11.0592/120=18 p_U2270B_CFE = 0; delay_2(28);//280*11.0592/120=26写0 } } /*******************写一个block*******************/ void write_block(uchar addr,uchar data *data p) { uchar i,j; for(i = 0;i < 4;i++)//block0数据 { DATA = *(p++); for(j = 0;j < 8;j++) { write_bit(BIT0); DATA >>= 1; } } DATA = addr <<= 5;//0地址 for(i = 0;i < 3;i++) { write_bit(BIT7); DATA <<= 1; } } /*************************************************/ void write_password(uchar data *data p) { uchar i,j; for(i = 0;i < 4;i++)// { DATA = *(p++); for(j = 0;j < 8;j++) { write_bit(BIT0); DATA >>= 1; } } } /*************************************************/ void main() { initial(); TI = RI = 0; ES = 1; EA = 1; delay_2(28); //f_readcard(); while(1) { f_readcard(); //读卡 f_writecard(command1); //写卡 f_clearpassword(); //清除密码 f_changepassword(); //修改密码 } }

标签： 12345

上传时间： 2017-10-20

上传用户：my_lcs
RFID读卡模块RC522串口读写器13.56mhz ic卡设计射频模块串口文档资料+Rc522Ma

RFID读卡模块RC522串口读写器13.56mhz ic卡设计射频模块串口文档资料+Rc522Manager上位机API工具软件1).MF RC522 是应用于 13.56MHz 非接触式通信中高集成度读写卡系列芯片中的一员。是 NXP 公司针对“三表”应用推出的一款低电压、低成本、体积小的非接触式读写卡芯片，是智能仪表和便携式手持设备研发的较好选择。 2).MF RC522 利用了先进的调制和解调概念，完全集成了在 13.56MHz 下所有类型的被动非接触式通信方式和协议。支持 ISO14443A 的多层应用。其内部发送器部分可驱动读写器天线与ISO 14443A/MIFARE卡和应答机的通信，无需其它的电路。接收器部分提供一个坚固而有效的解调和解码电路，用于处理 ISO14443A 兼容的应答器信号。数字部分处理 ISO14443A 帧和错 PcdAnticoll(unsigned char *pSnr) //防冲撞 0101：PcdSelect(unsigned char *pSnr) //卡片选择 0110：PcdAuthState(unsigned char auth_mode,unsigned char addr,unsigned char *pKey,unsigned char *pSnr) //验证卡片密码 0111：PcdRead(unsigned char addr,unsigned

标签： rfid rc522 串口

上传时间： 2021-12-22

上传用户：