Precision, Low Noise, CMOS, Rail-to-Rail, Input/Output Operational Amplifiers Data Sheet AD8605/AD8606/AD8608The AD8605, AD8606, and AD86081 are single, dual, and quad rail-to-rail input and output, single-supply amplifiers. They feature very low offset voltage, low input voltage and current noise, and wide signal bandwidth. They use the Analog Devices, Inc. patented DigiTrim® trimming technique, which achieves
标签： 运算放大器
上传时间： 2022-02-02
上传用户：
The PW2606B is a front-end over voltage and over current protection device. It achieves wide inputvoltage range from 2.5VDC to 40VDC. The over voltage threshold can be programmed externally orset to internal default setting. The low resistance of integrated power path nFET switch ensures betterperformance for battery charging system applications. It can deliver up to 1A current to satisfy thebattery supply system. It integrates the over-temperature protection shutdown and auto-recoverycircuit with hysteresis to protect against over current events
标签： pw2606b
上传时间： 2022-02-11
上传用户：
文章提出了一种基于AT89S51单片机的智能家居系统的设计,该系统具有室内煤气以及烟雾的检测、家庭室内防盗等功能。文章详细分析了系统的总体设计,详尽分析并设计了煤气传感器模块、烟雾传感器模块、人体红外感应传感器模块、报警模块等各硬件部分,并利用PROTUES软件进行了系统仿真。仿真结果证明:系统具有成本低、效率高、操作方便等优点,达到了预期设计的效果。This paper presents the design of an intelligent home system based on AT89S51 microcontroller.The system has the functions of detecting indoor gas and smoke,guarding against theft in the home,and so on.The overall design of the system is analyzed in detail.The gas sensor module,smoke sensor module,human infrared sensor module,alarm module and other hardware parts are analyzed and designed in detail,and the system simulation is carried out using PROTUES software.The simulation results show that the system has the advantages of low cost,high efficiency,convenient operation and so on,and achieves the expected design effect.
上传时间： 2022-03-28
上传用户：
为设计高效率、低损耗的PFC电路,本文基于UCC28019进行电路设计。以UCC28019输出的PWM波形来控制Boost升压斩波为核心电路,使电路中的电容交替地充放电、电感交替的储存和释放能量,最后实现在输入AC20V~24V电压情况下稳定输出DC38V。测试结果表明,系统实现效率为95%左右,电压调整率小于1%,电源功率因数0.99。交流输入电压为19.0-25.8 V时,输出直流电压稳定性较好,电感无明显啸叫且纹波小,具有一定的带负载能力和实用性。In order to design the PFC circuit with high efficiency and low loss,this paper designs the circuit based on UCC28019.The PWM waveform output by UCC28019 is used to control boost chopper as the core circuit,which alternately charges and discharges capacitors,stores and releases energy by inductors,and finally achieves stable output of DC38 V under the input voltage of AC20 V~24 V.The test results show that the system achieves about 95% efficiency,the voltage adjustment rate is less than 1%,the power factor is 0.99,and the AC input voltage is 19.0-25.8 V.The output DC voltage stability is good,the inductance has no obvious whistle and the ripple is small,so it has certain load capacity and practicability.
上传时间： 2022-04-03
上传用户：
本文首次设计并验证了基于macom三合一芯片设计的光模块电路,该电路旨在提供一种满足SFF-8472中规定的数字诊断功能的低成本SFP+模块。电路采用激光器驱动、限幅放大器、控制器以及时钟恢复单元集成的单芯片,在保证高精度数字诊断功能基础上,实现了低成本高可靠的特点。该电路在光接收接口组件与激光器驱动和限幅放大器单元的限幅放大器部分之间接入滤波器来提高模块的灵敏度及信号质量。在控制器单元的数字电位器的引脚上采用外加电阻的方式避免出现上电不发光的故障问题。该研究结果为下一代SFP-DD光模块设计与开发工作,奠定了一定的理论与实践基础。This paper designs and validates the optical module circuit based on the MACOM Trinity chip for the first time.This circuit aims to provide a low-cost SFP module which meets the digital diagnosis function specified in SFF-8472.The circuit uses a single chip integrated with laser driver,limiting amplifier,controller and clock recovery unit.On the basis of ensuring high precision digital diagnosis function,it achieves the characteristics of low cost and high reliability.The circuit connects a filter between the optical receiving interface module and the limiting amplifier part of the laser driver and limiting amplifier unit to improve the sensitivity and signal quality of the module.The pin of the digital potentiometer in the controller unit is equipped with an external resistance to avoid the problem of power failure.The research results lay a theoretical and practical foundation for optical module design in high-speed data center.
上传时间： 2022-04-03
上传用户：
