Abstract: This article discusses application circuits for Maxim force/sense digital-to-analog converters (DACs). Applications include:selectable fixed-gain DAC, programmable gain DAC, photodiode bias control, amperometric sensor control, digitally programmablecurrent source, Kelvin load sensing, temperature sensing, and high current DAC output. A brief description of the various DAC outputconfigurations is also given.
标签： DAC
上传时间： 2013-11-04
上传用户：youmo81
Abstract: Using a DAC and a microprocessor supervisor, the system safety can be improved in industrial controllers, programmablelogiccontrollers (PLC), and data-acquisition systems. The analog output is set to zero-scale (or pin-programmable midscale) when amicroprocessor failure, optocoupler failure, or undervoltage condition occurs. A simple application is shown on how to implement thisfunction.
上传时间： 2013-10-17
上传用户：sjb555
Abstract: Transimpedance amplifiers (TIAs) are widely used to translate the current output of sensors like photodiode-to-voltagesignals, since several circuits and instruments can only accept voltage input. An operational amplifier with a feedback resistor fromoutput to the inverting input is the most straightforward implementation of such a TIA. However, even this simple TIA circuit requirescareful trade-offs among noise gain, offset voltage, bandwidth, and stability. Clearly stability in a TIA is essential for good, reliableperformance. This application note explains the empirical calculations for assessing stability and then shows how to fine-tune theselection of the feedback phase-compensation capacitor.
标签： Transimpedance Stabilize Amplifier Your
上传时间： 2013-11-13
上传用户：daoyue
Construction Strategy of ESD Protection CircuitAbstract： The principles used to construct ESD protection on circuits and the basic conceptions of ESD protection design are presented.Key words：ESD protection/On circuit, ESD design window, ESD current path1 引言静电放电（ESD，Electrostatic Discharge）给电子器件环境会带来破坏性的后果。它是造成集成电路失效的主要原因之一。随着集成电路工艺不断发展，互补金属氧化物半导体（CMOS，Complementary Metal-Oxide Semiconductor）的特征尺寸不断缩小，金属氧化物半导体(MOS, Metal-Oxide Semiconductor)的栅氧厚度越来越薄，MOS 管能承受的电流和电压也越来越小，因此要进一步优化电路的抗ESD 性能，需要从全芯片ESD 保护结构的设计来进行考虑。
标签： Construction Strategy ESD of
上传时间： 2013-11-09
上传用户：Aidane
Abstract: Using a wafer-level package (WLP) can reduce the overall size and cost of your solution.However when using a WLP IC, the printed circuit board (PCB) layout can become more complex and, ifnot carefully planned, result in an unreliable design. This article presents some PCB designconsiderations and general recommendations for choosing a 0.4mm- or 0.5mm-pitch WLP for yourapplication.
标签： Considerations Guidelines and Design
上传时间： 2013-10-14
上传用户：ysystc699
Abstract: This application note explains how to layout the MAX20021/MAX20022 automotive quad powermanagementICs (PMICs) to maximize performance and minimize emissions. Example images of a fourlayerlayout are provided.
上传时间： 2013-11-19
上传用户：18711024007
The Circuit Designer’s Companion Second edition Tim Williams
标签： Designers Companion Circuit PCB
上传时间： 2013-11-04
上传用户：fredguo
磁芯电感器的谐波失真分析 摘 要：简述了改进铁氧体软磁材料比损耗系数和磁滞常数ηB，从而降低总谐波失真THD的历史过程，分析了诸多因数对谐波测量的影响，提出了磁心性能的调控方向。 关键词：比损耗系数， 磁滞常数ηB ，直流偏置特性DC-Bias，总谐波失真THD Analysis on THD of the fer rite co res u se d i n i nductancShi Yan Nanjing Finemag Technology Co. Ltd., Nanjing 210033 Abstract: Histrory of decreasing THD by improving the ratio loss coefficient and hysteresis constant of soft magnetic ferrite is briefly narrated. The effect of many factors which affect the harmonic wave testing is analysed. The way of improving the performance of ferrite cores is put forward. Key words: ratio loss coefficient，hysteresis constant，DC-Bias，THD 近年来，变压器生产厂家和软磁铁氧体生产厂家，在电感器和变压器产品的总谐波失真指标控制上，进行了深入的探讨和广泛的合作，逐步弄清了一些似是而非的问题。从工艺技术上采取了不少有效措施，促进了质量问题的迅速解决。本文将就此热门话题作一些粗浅探讨。 一、 历史回顾 总谐波失真（Total harmonic distortion） ，简称THD，并不是什么新的概念，早在几十年前的载波通信技术中就已有严格要求<1>。1978年邮电部公布的标准YD/Z17－78“载波用铁氧体罐形磁心”中，规定了高μQ材料制作的无中心柱配对罐形磁心详细的测试电路和方法。如图一电路所示，利用LC组成的150KHz低通滤波器在高电平输入的情况下测量磁心产生的非线性失真。这种相对比较的实用方法，专用于无中心柱配对罐形磁心的谐波衰耗测试。 这种磁心主要用于载波电报、电话设备的遥测振荡器和线路放大器系统，其非线性失真有很严格的要求。 图中 ZD —— QF867 型阻容式载频振荡器，输出阻抗 150Ω， Ld47 —— 47KHz 低通滤波器，阻抗 150Ω，阻带衰耗大于61dB， Lg88 ——并联高低通滤波器，阻抗 150Ω，三次谐波衰耗大于61dB Ld88 ——并联高低通滤波器，阻抗 150Ω，三次谐波衰耗大于61dB FD —— 30～50KHz 放大器， 阻抗 150Ω， 增益不小于 43 dB，三次谐波衰耗b3(0)≥91 dB, DP —— Qp373 选频电平表，输入高阻抗， L ——被测无心罐形磁心及线圈， C ——聚苯乙烯薄膜电容器CMO-100V-707APF±0.5%,二只。 测量时，所配用线圈应用丝包铜电磁线SQJ9×0.12(JB661-75)在直径为16.1mm的线架上绕制 120 匝， （线架为一格） ， 其空心电感值为 318μH（误差1％） 被测磁心配对安装好后，先调节振荡器频率为 36.6～40KHz， 使输出电平值为+17.4 dB， 即选频表在 22′端子测得的主波电平 （P2）为+17.4 dB，然后在33′端子处测得输出的三次谐波电平（P3）， 则三次谐波衰耗值为：b3(+2)= P2+S+ P3 式中：S 为放大器增益dB 从以往的资料引证， 就可以发现谐波失真的测量是一项很精细的工作，其中测量系统的高、低通滤波器，信号源和放大器本身的三次谐波衰耗控制很严，阻抗必须匹配，薄膜电容器的非线性也有相应要求。滤波器的电感全由不带任何磁介质的大空心线圈绕成，以保证本身的“洁净” ，不至于造成对磁心分选的误判。 为了满足多路通信整机的小型化和稳定性要求， 必须生产低损耗高稳定磁心。上世纪 70 年代初，1409 所和四机部、邮电部各厂，从工艺上改变了推板空气窑烧结，出窑后经真空罐冷却的落后方式，改用真空炉，并控制烧结、冷却气氛。技术上采用共沉淀法攻关试制出了μQ乘积 60 万和 100 万的低损耗高稳定材料，在此基础上，还实现了高μ7000～10000材料的突破，从而大大缩短了与国外企业的技术差异。当时正处于通信技术由FDM（频率划分调制）向PCM（脉冲编码调制） 转换时期， 日本人明石雅夫发表了μQ乘积125 万为 0.8×10 ，100KHz）的超优铁氧体材料<3>，其磁滞系数降为优铁
上传时间： 2014-12-24
上传用户：7891
Integrated EMI/Thermal Design forSwitching Power SuppliesWei ZhangThesis submitted to the Faculty of theVirginia Polytechnic Institute and State Universityin partial fulfillment of the requirements for the degree of Integrated EMI/Thermal Design forSwitching Power SuppliesWei Zhang(ABSTRACT)This work presents the modeling and analysis of EMI and thermal performancefor switch power supply by using the CAD tools. The methodology and design guidelinesare developed.By using a boost PFC circuit as an example, an equivalent circuit model is builtfor EMI noise prediction and analysis. The parasitic elements of circuit layout andcomponents are extracted analytically or by using CAD tools. Based on the model, circuitlayout and magnetic component design are modified to minimize circuit EMI. EMI filtercan be designed at an early stage without prototype implementation.In the second part, thermal analyses are conducted for the circuit by using thesoftware Flotherm, which includes the mechanism of conduction, convection andradiation. Thermal models are built for the components. Thermal performance of thecircuit and the temperature profile of components are predicted. Improved thermalmanagement and winding arrangement are investigated to reduce temperature.In the third part, several circuit layouts and inductor design examples are checkedfrom both the EMI and thermal point of view. Insightful information is obtained.
上传时间： 2013-11-10
上传用户：1595690
Abstract: Electrolytic capacitors are notorious for short lifetimes in high-temperature applications such asLED light bulbs. The careful selection of these devices with proper interpretation of their specifications isessential to ensure that they do not compromise the life of the end product. This application notediscusses this problem with electrolytic capacitors in LED light bulbs and provides an analysis that showshow it is possible to use electrolytics in such products.
上传时间： 2013-11-17
上传用户：asdfasdfd
