Abstract: Uses the MAX641 switching controller and an external discrete charge pump to step up the input voltage. This circuitcan service low loads and is efficient when the output is two, three, four times the input voltage. Adding the MAX627 MOSdriver can further increase the output current capability.
上传时间： 2013-11-15
上传用户：zwei41
Abstract: Rail splitting is creating an artificial virtual ground as a reference voltage. It is used to set the signalto match the op amp's "sweet spot." An op amp has the most linear- and distortion-free qualities at that sweetspot. Typically, the sweet spot occurs near the center between the single power rail and ground. In the case ofa number of signals, the virtual ground can control channel DC errors when multiplexing or switching thesignals.
上传时间： 2013-10-23
上传用户：wushengwu
The CN3052A is a complete constant-current /constant voltage linear charger for single cell Li-ion and Li Polymer rechargeable batteries. The device contains an on-chip power MOSFET and eliminates the need for the external sense resistor and blocking diode.
上传时间： 2013-11-10
上传用户：子虚乌有
In this paper, two types of MMIC voltage controlled oscillators have been successfully demonstrated. The first chip with single tuning diode shows the excellent tuning linearity. The second chip with two tuning diodes can improve the tuning bandwidth.
上传时间： 2013-10-17
上传用户：xjz632
The LT®1943 is a highly integrated, 4-output regulatordesigned to power large TFT LCD panels. The LT1943employs switching regulators—instead of linear regulators—to minimize power dissipation and accommodate awide input voltage range. The wide input range, 4.5V to22V, allows it to accept a variety of power sources,including the commonly used 5V, 12V and 19V AC adaptors.
上传时间： 2013-10-19
上传用户：yuhaihua_tony
Linear Technology offers a variety of devices that simplifyconverting power from a USB cable, but the LTC®3455represents the highest level of functional integration yet. The LTC3455 seamlessly manages power flowbetween an AC adapter, USB cable and Li-ion battery,while complying with USB power standards, all from a4mm × 4mm QFN package. In addtion, two high efficiencysynchronous buck converters generate low voltage railswhich most USB-powered peripherals require. TheLTC3455 also provides power-on reset signals for themicroprocessor, a Hot SwapTM output for poweringmemory cards as well as an uncommitted gain blocksuitable for use as a low-battery comparator or an LDOcontroller. The PCB real estate required for the entire USBpower control circuit and two DC/DC converters is only225mm2.
上传时间： 2013-11-02
上传用户：名爵少年
The core voltages for FPGAs are moving lower as a resultof advances in the fabrication process. The newest FPGAfamily from Altera, the Stratix® II, now requires a corevoltage of 1.2V and the Stratix, Stratix GX, HardCopy®Stratix and CycloneTM families require a core voltage of1.5V. This article discusses how to power the core and I/Oof low voltage FPGAs using the latest step-down switchmode controllers from Linear Technology Corporation.
上传时间： 2013-10-08
上传用户：wangfei22
The LTC®3414 offers a compact and efficient voltage regulatorsolution for point of load conversion in electronicsystems that require low output voltages (down to 0.8V)from a 2.5V to 5V power bus. Internal power MOSFETswitches, with only 67mW on-resistance, allow theLTC3414 to deliver up to 4A of output current with efficiencyas high as 94%. The LTC3414 saves space by operatingwith switching frequencies as high as 4MHz, enabling theuse of tiny inductors and capacitors.
上传时间： 2014-01-03
上传用户：dongbaobao
Multiple-voltage electronics systems often requirecomplex supply voltage tracking or sequencing, whichif not met, can result in system faults or even permanentfailures in the fi eld. The design diffi culties in meetingthese requirements are often compounded in distributedpowerarchitectures where point-of-load (POL) DC/DCconverters or linear regulators are scattered across PCboard space, sometimes on different board planes. Theproblem is that power supply circuitry is often the lastcircuitry to be designed into the board, and it must beshoehorned into whatever little board real estate is left.Often, a simple, drop-in, fl exible solution is needed tomeet these requirements.
上传时间： 2013-10-08
上传用户：15071087253
DC/DC 升压IC：The FP6291 is a current mode boost DC-DC converter. Its PWM circuitry with built-in 0.25 Ω power MOSFET make this regulator highly power efficient. The internal compensation network also minimizes as much as 6 external component counts. The non-inverting input of error amplifier connects to a 0.6V precision reference voltage and internal soft-start function can reduce the inrush current. The FP6291 is available in the SOT23-6L package and provides space-saving PCB for the application fields.
上传时间： 2013-11-07
上传用户：3294322651
