开关在电路中起接通信号或断开信号的作用。最常见的可控开关是继电器，当给驱动继电器的驱动电路加高电平或低电平时，继电器就吸合或释放，其触点接通或断开电路。CMOS模拟开关是一种可控开关，它不象继电器那样可以用在大电流、高电压场合，只适于处理幅度不超过其工作电压、电流较小的模拟或数字信号。 一、常用CMOS模拟开关引脚功能和工作原理 1.四双向模拟开关CD4066 CD4066 的引脚功能如图1所示。每个封装内部有4个独立的模拟开关，每个模拟开关有输入、输出、控制三个端子，其中输入端和输出端可互换。当控制端加高电平时，开关导通；当控制端加低电平时开关截止。模拟开关导通时，导通电阻为几十欧姆；模拟开关截止时，呈现很高的阻抗，可以看成为开路。模拟开关可传输数字信号和模拟信号，可传输的模拟信号的上限频率为40MHz。各开关间的串扰很小，典型值为－50dB。
上传时间： 2013-10-27
上传用户：bibirnovis
Radio Frequency Integrated Circuit Design I enjoyed reading this book for a number of reasons. One reason is that itaddresses high-speed analog design in the context of microwave issues. This isan advanced-level book, which should follow courses in basic circuits andtransmission lines. Most analog integrated circuit designers in the past workedon applications at low enough frequency that microwave issues did not arise.As a consequence, they were adept at lumped parameter circuits and often notcomfortable with circuits where waves travel in space. However, in order todesign radio frequency (RF) communications integrated circuits (IC) in thegigahertz range, one must deal with transmission lines at chip interfaces andwhere interconnections on chip are far apart. Also, impedance matching isaddressed, which is a topic that arises most often in microwave circuits. In mycareer, there has been a gap in comprehension between analog low-frequencydesigners and microwave designers. Often, similar issues were dealt with in twodifferent languages. Although this book is more firmly based in lumped-elementanalog circuit design, it is nice to see that microwave knowledge is brought inwhere necessary.Too many analog circuit books in the past have concentrated first on thecircuit side rather than on basic theory behind their application in communications.The circuits usually used have evolved through experience, without asatisfying intellectual theme in describing them. Why a given circuit works bestcan be subtle, and often these circuits are chosen only through experience. Forthis reason, I am happy that the book begins first with topics that require anintellectual approach—noise, linearity and filtering, and technology issues. Iam particularly happy with how linearity is introduced (power series). In therest of the book it is then shown, with specific circuits and numerical examples,how linearity and noise issues arise.
上传时间： 2014-12-23
上传用户：han_zh
介绍高速电路的设计
标签： High-speed Digital Design 高速数字
上传时间： 2013-10-16
上传用户：yt1993410
减小电磁干扰的印刷电路板设计原则 内 容 摘要……1 1 背景…1 1.1 射频源.1 1.2 表面贴装芯片和通孔元器件.1 1.3 静态引脚活动引脚和输入.1 1.4 基本回路……..2 1.4.1 回路和偶极子的对称性3 1.5 差模和共模…..3 2 电路板布局…4 2.1 电源和地…….4 2.1.1 感抗……4 2.1.2 两层板和四层板4 2.1.3 单层板和二层板设计中的微处理器地.4 2.1.4 信号返回地……5 2.1.5 模拟数字和高压…….5 2.1.6 模拟电源引脚和模拟参考电压.5 2.1.7 四层板中电源平面因该怎么做和不应该怎么做…….5 2.2 两层板中的电源分配.6 2.2.1 单点和多点分配.6 2.2.2 星型分配6 2.2.3 格栅化地.7 2.2.4 旁路和铁氧体磁珠……9 2.2.5 使噪声靠近磁珠……..10 2.3 电路板分区…11 2.4 信号线……...12 2.4.1 容性和感性串扰……...12 2.4.2 天线因素和长度规则...12 2.4.3 串联终端传输线…..13 2.4.4 输入阻抗匹配...13 2.5 电缆和接插件……...13 2.5.1 差模和共模噪声……...14 2.5.2 串扰模型……..14 2.5.3 返回线路数目..14 2.5.4 对板外信号I/O的建议14 2.5.5 隔离噪声和静电放电ESD .14 2.6 其他布局问题……...14 2.6.1 汽车和用户应用带键盘和显示器的前端面板印刷电路板...15 2.6.2 易感性布局…...15 3 屏蔽..16 3.1 工作原理…...16 3.2 屏蔽接地…...16 3.3 电缆和屏蔽旁路………………..16 4 总结…………………………………………17 5 参考文献………………………17
上传时间： 2013-10-24
上传用户：18165383642
This document provides practical, common guidelines for incorporating PCI Express interconnect layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10- layer or more server baseboard designs. Guidelines and constraints in this document are intended for use on both baseboard and add-in card PCB designs. This includes interconnects between PCI Express devices located on the same baseboard (chip-to-chip routing) and interconnects between a PCI Express device located “down” on the baseboard and a device located “up” on an add-in card attached through a connector. This document is intended to cover all major components of the physical interconnect including design guidelines for the PCB traces, vias and AC coupling capacitors, as well as add-in card edge-finger and connector considerations. The intent of the guidelines and examples is to help ensure that good high-speed signal design practices are used and that the timing/jitter and loss/attenuation budgets can also be met from end-to-end across the PCI Express interconnect. However, while general physical guidelines and suggestions are given, they may not necessarily guarantee adequate performance of the interconnect for all layouts and implementations. Therefore, designers should consider modeling and simulation of the interconnect in order to ensure compliance to all applicable specifications. The document is composed of two main sections. The first section provides an overview of general topology and interconnect guidelines. The second section concentrates on physical layout constraints where bulleted items at the beginning of a topic highlight important constraints, while the narrative that follows offers additional insight.
上传时间： 2013-10-15
上传用户：busterman
为解决直流逆变交流的问题，有效地利用能源，让电源输出最大功率，设计了高性能的基于IR2101最大功率跟踪逆变器，并以SPMC75F2413A单片机作为主控制器。高电压、高速功率的MOSFET或IGBT驱动器IR2101采用高度集成的电平转换技术，同时上管采用外部自举电容上电，能够稳定高效地驱动MOS管。该逆变器可以实现DC/AC的转换，最大功率点的跟踪等功能。实际测试结果表明，该逆变器系统具有跟踪能力强，稳定性高，反应灵敏等特点，该逆变器不仅可应用于普通的电源逆变系统，而且可应用于光伏并网发电的逆变系统，具有广泛的市场前景。 Abstract: To solve the problem of DC-AC inverter， and to utilize solar energy more efficiently， the design of maximum power point tracking inverter based on IR2101 was achieved with a high-performance， which can make the system output power maximum. SPMC75F2413A was adopted as main controller. IR2101 is a high voltage， high speed power MOSFET and IGBT driver. It adopted highly integrated voltage level transforming technology， and an external bootstrap capacitor was used， which could drive MOS tube efficiently and stably. Many functions are achieved in the system， such as DC/AC conversion， maximun power point tracking， etc. The actual test result shows that the inverter system has characteristics of strong tracking ability， high stability and reacting quickly. The design can not only be used in ordinary power inverter system， but also be used in photovoltaic power inverter system. The design has certain marketing prospects
上传时间： 2013-11-17
上传用户：lliuhhui
TLC2543是TI公司的12位串行模数转换器，使用开关电容逐次逼近技术完成A/D转换过程。由于是串行输入结构，能够节省51系列单片机I/O资源；且价格适中，分辨率较高，因此在仪器仪表中有较为广泛的应用。 TLC2543的特点 （1）12位分辩率A/D转换器； （2）在工作温度范围内10μs转换时间； （3）11个模拟输入通道； （4）3路内置自测试方式； （5）采样率为66kbps； （6）线性误差±1LSBmax； （7）有转换结束输出EOC； （8）具有单、双极性输出； （9）可编程的MSB或LSB前导； （10）可编程输出数据长度。 TLC2543的引脚排列及说明 TLC2543有两种封装形式：DB、DW或N封装以及FN封装，这两种封装的引脚排列如图1，引脚说明见表1 TLC2543电路图和程序欣赏 #include<reg52.h> #include<intrins.h> #define uchar unsigned char #define uint unsigned int sbit clock=P1^0; sbit d_in=P1^1; sbit d_out=P1^2; sbit _cs=P1^3; uchar a1,b1,c1,d1; float sum,sum1; double sum_final1; double sum_final; uchar duan[]={0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f}; uchar wei[]={0xf7,0xfb,0xfd,0xfe}; void delay(unsigned char b) //50us { unsigned char a; for(;b>0;b--) for(a=22;a>0;a--); } void display(uchar a,uchar b,uchar c,uchar d) { P0=duan[a]|0x80; P2=wei[0]; delay(5); P2=0xff; P0=duan[b]; P2=wei[1]; delay(5); P2=0xff; P0=duan[c]; P2=wei[2]; delay(5); P2=0xff; P0=duan[d]; P2=wei[3]; delay(5); P2=0xff; } uint read(uchar port) { uchar i,al=0,ah=0; unsigned long ad; clock=0; _cs=0; port<<=4; for(i=0;i<4;i++) { d_in=port&0x80; clock=1; clock=0; port<<=1; } d_in=0; for(i=0;i<8;i++) { clock=1; clock=0; } _cs=1; delay(5); _cs=0; for(i=0;i<4;i++) { clock=1; ah<<=1; if(d_out)ah|=0x01; clock=0; } for(i=0;i<8;i++) { clock=1; al<<=1; if(d_out) al|=0x01; clock=0; } _cs=1; ad=(uint)ah; ad<<=8; ad|=al; return(ad); } void main() { uchar j; sum=0;sum1=0; sum_final=0; sum_final1=0; while(1) { for(j=0;j<128;j++) { sum1+=read(1); display(a1,b1,c1,d1); } sum=sum1/128; sum1=0; sum_final1=(sum/4095)*5; sum_final=sum_final1*1000; a1=(int)sum_final/1000; b1=(int)sum_final%1000/100; c1=(int)sum_final%1000%100/10; d1=(int)sum_final%10; display(a1,b1,c1,d1); } }
上传时间： 2013-11-19
上传用户：shen1230
#include<iom16v.h> #include<macros.h> #define uint unsigned int #define uchar unsigned char uint a,b,c,d=0; void delay(c) { for for(a=0;a<c;a++) for(b=0;b<12;b++); }; uchar tab[]={ 0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8,0x80,0x90,
上传时间： 2013-10-21
上传用户：13788529953
HIGH SPEED 8051 μC CORE - Pipe-lined Instruction Architecture; Executes 70% of Instructions in 1 or 2 System Clocks - Up to 25MIPS Throughput with 25MHz System Clock - 22 Vectored Interrupt Sources MEMORY - 4352 Bytes Internal Data RAM (256 + 4k) - 64k Bytes In-System Programmable FLASH Program Memory - External Parallel Data Memory Interface – up to 5Mbytes/sec DIGITAL PERIPHERALS - 64 Port I/O; All are 5V tolerant - Hardware SMBusTM (I2CTM Compatible), SPITM, and Two UART Serial Ports Available Concurrently - Programmable 16-bit Counter/Timer Array with 5 Capture/Compare Modules - 5 General Purpose 16-bit Counter/Timers - Dedicated Watch-Dog Timer; Bi-directional Reset CLOCK SOURCES - Internal Programmable Oscillator: 2-to-16MHz - External Oscillator: Crystal, RC, C, or Clock - Real-Time Clock Mode using Timer 3 or PCA SUPPLY VOLTAGE ........................ 2.7V to 3.6V - Typical Operating Current: 10mA @ 25MHz - Multiple Power Saving Sleep and Shutdown Modes 100-Pin TQFP (64-Pin Version Available) Temperature Range: –40°C to +85°C
标签： C8051F020
上传时间： 2013-10-12
上传用户：lalalal
a_bit equ 20h ;个位数存放处 b_bit equ 21h ;十位数存放处 temp equ 22h ;计数器寄存器 star: mov temp,#0 ;初始化计数器 stlop: acall display inc temp mov a,temp cjne a,#100,next ;=100重来 mov temp,#0 next: ljmp stlop ;显示子程序 display: mov a,temp ;将temp中的十六进制数转换成10进制 mov b,#10 ;10进制/10=10进制 div ab mov b_bit,a ;十位在a mov a_bit,b ;个位在b mov dptr,#numtab ;指定查表启始地址 mov r0,#4 dpl1: mov r1,#250 ;显示1000次 dplop: mov a,a_bit ;取个位数 MOVC A,@A+DPTR ;查个位数的7段代码 mov p0,a ;送出个位的7段代码
上传时间： 2013-11-06
上传用户：lx9076
