The LTC®1966 is a true RMS-to-DC converter that uses aDS computational technique to make it dramatically simplerto use, significantly more accurate, lower in powerconsumption and more flexible than conventional logantilogRMS-to-DC converters. The LTC1966 RMS-to-DCconverter has an input signal range from 5mVRMS to1.5VRMS (a 50dB dynamic range with a single 5V supplyrail) and a 3dB bandwidth of 800kHz with signal crestfactors up to four.
上传时间： 2013-10-12
上传用户：qilin
The STM32F10xxx microcontroller family embeds up to three advanced 12-bit ADCs (depending on the device) with a conversion time down to 1 μs. A self-calibration feature is provided to enhance ADC accuracy versus environmental condition changes.
上传时间： 2014-12-23
上传用户：eastimage
开关在电路中起接通信号或断开信号的作用。最常见的可控开关是继电器，当给驱动继电器的驱动电路加高电平或低电平时，继电器就吸合或释放，其触点接通或断开电路。CMOS模拟开关是一种可控开关，它不象继电器那样可以用在大电流、高电压场合，只适于处理幅度不超过其工作电压、电流较小的模拟或数字信号。 一、常用CMOS模拟开关引脚功能和工作原理 1.四双向模拟开关CD4066 CD4066 的引脚功能如图1所示。每个封装内部有4个独立的模拟开关，每个模拟开关有输入、输出、控制三个端子，其中输入端和输出端可互换。当控制端加高电平时，开关导通；当控制端加低电平时开关截止。模拟开关导通时，导通电阻为几十欧姆；模拟开关截止时，呈现很高的阻抗，可以看成为开路。模拟开关可传输数字信号和模拟信号，可传输的模拟信号的上限频率为40MHz。各开关间的串扰很小，典型值为－50dB。
上传时间： 2013-10-27
上传用户：bibirnovis
减小电磁干扰的印刷电路板设计原则 内 容 摘要……1 1 背景…1 1.1 射频源.1 1.2 表面贴装芯片和通孔元器件.1 1.3 静态引脚活动引脚和输入.1 1.4 基本回路……..2 1.4.1 回路和偶极子的对称性3 1.5 差模和共模…..3 2 电路板布局…4 2.1 电源和地…….4 2.1.1 感抗……4 2.1.2 两层板和四层板4 2.1.3 单层板和二层板设计中的微处理器地.4 2.1.4 信号返回地……5 2.1.5 模拟数字和高压…….5 2.1.6 模拟电源引脚和模拟参考电压.5 2.1.7 四层板中电源平面因该怎么做和不应该怎么做…….5 2.2 两层板中的电源分配.6 2.2.1 单点和多点分配.6 2.2.2 星型分配6 2.2.3 格栅化地.7 2.2.4 旁路和铁氧体磁珠……9 2.2.5 使噪声靠近磁珠……..10 2.3 电路板分区…11 2.4 信号线……...12 2.4.1 容性和感性串扰……...12 2.4.2 天线因素和长度规则...12 2.4.3 串联终端传输线…..13 2.4.4 输入阻抗匹配...13 2.5 电缆和接插件……...13 2.5.1 差模和共模噪声……...14 2.5.2 串扰模型……..14 2.5.3 返回线路数目..14 2.5.4 对板外信号I/O的建议14 2.5.5 隔离噪声和静电放电ESD .14 2.6 其他布局问题……...14 2.6.1 汽车和用户应用带键盘和显示器的前端面板印刷电路板...15 2.6.2 易感性布局…...15 3 屏蔽..16 3.1 工作原理…...16 3.2 屏蔽接地…...16 3.3 电缆和屏蔽旁路………………..16 4 总结…………………………………………17 5 参考文献………………………17
上传时间： 2013-10-24
上传用户：18165383642
目录 第一章 传输线理论 一 传输线原理 二 微带传输线 三 微带传输线之不连续分析 第二章 被动组件之电感设计与分析 一 电感原理 二 电感结构与分析 三 电感设计与模拟 电感分析与量测
标签： 传输线
上传时间： 2013-12-12
上传用户：浩子GG
特点(FEATURES) 精确度0.1%满刻度 (Accuracy 0.1%F.S.) 可作各式数学演算式功能如:A+B/A-B/AxB/A/B/A&B(Hi or Lo)/|A| (Math functioA+B/A-B/AxB/A/B/A&B(Hi&Lo)/|A|/etc.....) 16 BIT 类比输出功能(16 bit DAC isolating analog output function) 输入/输出1/输出2绝缘耐压2仟伏特/1分钟(Dielectric strength 2KVac/1min. (input/output1/output2/power)) 宽范围交直流两用电源设计(Wide input range for auxiliary power) 尺寸小,稳定性高(Dimension small and High stability)
上传时间： 2013-11-24
上传用户：541657925
Abstract: It is critically important that lithium-ion battery stacks have a good battery-management system for monitoring many cellvoltages and cell temperatures. Without that monitoring, thermal runaway can lead to a battery explosion. This design idea presentsa low-power circuit that measures the temperature of up to 12 thermistors. It powers and configures the multiplexers, and also putsthe muxes into shutdown to save power when not measuring temperatures.
上传时间： 2013-10-29
上传用户：xwd2010
The LTC®3414 offers a compact and efficient voltage regulatorsolution for point of load conversion in electronicsystems that require low output voltages (down to 0.8V)from a 2.5V to 5V power bus. Internal power MOSFETswitches, with only 67mW on-resistance, allow theLTC3414 to deliver up to 4A of output current with efficiencyas high as 94%. The LTC3414 saves space by operatingwith switching frequencies as high as 4MHz, enabling theuse of tiny inductors and capacitors.
上传时间： 2014-01-03
上传用户：dongbaobao
To this day, Power over Ethernet (PoE) continues to gainpopularity in today’s networking world. The 12.95Wdelivered to the Powered Device (PD) input supplied bythe Power Sourcing Equipment (PSE) is a universal supply.Each PD provides its own DC/DC conversion from anominal 48V supply, thus eliminating the need for a correctvoltage wall adapter. However, higher power devicescan not take advantage of standard PoE because of itspower limitations, and must rely on a large wall adapteras their primary supply. The new LTC4268-1 breaks thispower barrier by allowing for power of up to 35W for suchpower-hungry 2-pair PoE applications. The LTC4268-1provides a complete solution by integrating a high powerPD interface control with an isolated fl yback controller.
上传时间： 2014-12-24
上传用户：jasson5678
Typical industrial and automotive applications requiremultiple high current, low voltage power supply solutionsto drive everything from disc drives to microprocessors.For many of these applications, particularly thosethat have size constraints, the LT3501® dual step-downconverter is an attractive solution because it’s compactand inexpensive compared to a 2-chip solution. The dualconverter accommodates a 3V to 25V input voltage rangeand is capable of supplying up to 3A per channel. Thecircuit in Figure 1 produces 3.3V and 1.8V.
上传时间： 2014-12-24
上传用户：372825274
