The LTC®4099 high effi ciency USB power manager andLi-Ion/Polymer battery charger seamlessly managespower distribution from multiple sources in portableapplications. It is differentiated from other USB powermanagers by its bidirectional I2C port that allows the hostmicroprocessor to control and monitor all aspects of theUSB power management and battery charging processes.In addition, a programmable interrupt generation functionalerts the host microprocessor to changes in device statusand provides unprecedented control of power managementfunctions. This high degree of confi gurability allowspost-layout changes in operation, even changes in thefi eld, and it allows a single qualifi ed device to be usedin a variety of products, thus reducing design time andeasing inventory management.
上传时间： 2013-10-22
上传用户：18602424091
以AVR单片机ATmega8和USB接口器件PDIUSBD12为核心，基于标准的USB1.1协议，设计一种通用USB接口模块，以满足嵌入式系统中对USB接口的需求。对模块的硬件电路或单片机固件程序的硬件接口层稍加修改即可用于其他各种微处理器。该模块可为各种嵌入式系统增加USB接口,实现与USB主机系统通信。 Abstract: Based on AVR microcontroller ATmega8 and USB interface chip PDIUSBD12, a general USB interface module is designed according to USB1.1 protocol for various requirements of embedded systems. Only with few modifications in circuit or hardware abstract layer of firmware, the module can be used on many types of microprocessors. All kinds of embedded systems can realize high speed and stable communication with USB host systems, owing to the facility of this module.
上传时间： 2014-01-08
上传用户：赵云兴
The bootloader is stored in the internal boot ROM memory (system memory) of STM32devices. It is programmed by ST during production. Its main task is to download theapplication program to the internal Flash memory through one of the available serialperipherals (USART, CAN, USB, etc.). A communication protocol is defined for each serialinterface, with a compatible command set and sequences
上传时间： 2014-09-06
上传用户：417313137
The MSP-FET430U14 is a powerful flash emulation tool to quickly begin application development on the MSP430 MCU. It includes USB debugging interface used to program and debug the MSP430 in-system through the JTAG interface or the pin saving Spy Bi-Wire (2-wire JTAG) protocol. The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is ultra-low power, no external power supply is required. The debugging tool interfaces the MSP430 to the included integrated software environment and includes code to start your design immediately. The MSP-FET430UIF development tools supports development with all MSP430 flash devices
上传时间： 2013-10-28
上传用户：13691535575
PICKIT™ 2 PROGRAMMER-TO-GO USER GUIDE The PICkit 2 Programmer-To-Go functionality allows a PIC MCU memory image to be downloaded into the PICkit 2 unit for later programming into a specific PIC MCU. No software or PC is required to program devices once the PICkit 2 unit is set up for Programming-To-Go. A USB power source for the PICkit 2 is all that is needed.
标签： PROGRAMMER-TO PICKIT 8482
上传时间： 2013-10-29
上传用户：ca05991270
Although Stellaris microcontrollers have generous internal SRAM capabilities, certain applicationsmay have data storage requirements that exceed the 8 KB limit of the Stellaris LM3S8xx seriesdevices. Since microcontrollers do not have an external parallel data-bus, serial memory optionsmust be considered. Until recently, the ubiquitous serial EEPROM/flash device was the only serialmemory solution. The major limitations of EEPROM and flash technology are slow write speed, slowerase times, and limited write/erase endurance.Recently, serial SRAM devices have become available as a solution for high-speed dataapplications. The N256S08xxHDA series of devices, from AMI Semiconductor, offer 32 K x 8 bits oflow-power data storage, a fast Serial Peripheral Interface (SPI) serial bus, and unlimited write cycles.The parts are available in 8-pin SOIC and compact TSSOP packages.
上传时间： 2013-10-14
上传用户：cxl274287265
The MAX3243E device consists of three line drivers, five line receivers, and a dual charge-pump circuit with±15-kV ESD (HBM and IEC61000-4-2, Air-Gap Discharge) and ±8-kV ESD (IEC61000-4-2, Contact Discharge)protection on serial-port connection pins. The device meets the requirements of TIA/EIA-232-F and provides theelectrical interface between an asynchronous communication controller and the serial-port connector. Thiscombination of drivers and receivers matches that needed for the typical serial port used in an IBM PC/AT, orcompatible. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-Vsupply. In addition, the device includes an always-active noninverting output (ROUT2B), which allowsapplications using the ring indicator to transmit data while the device is powered down. The device operates atdata signaling rates up to 250 kbit/s and a maximum of 30-V/ms driver output slew rate.
标签： MULTICHANNEL 5.5 TO RS
上传时间： 2013-10-19
上传用户：ddddddd
The C500 microcontroller family usually provides only one on-chip synchronous serialchannel (SSC). If a second SSC is required, an emulation of the missing interface mayhelp to avoid an external hardware solution with additional electronic components.The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using optimized SW routines with a performance up to 25KBaud in Slave Mode with half duplex transmission and an overhead less than 60% atSAB C513 with 12 MHz. Due to the implementation in C this performance is not the limitof the chip. A pure implementation in assembler will result in a strong reduction of theCPU load and therefore increase the maximum speed of the interface. In addition,microcontrollers like the SAB C505 will speed up the interface by a factor of two becauseof an optimized architecture compared with the SAB C513.Moreover, this solution lays stress on using as few on-chip hardware resources aspossible. A more excessive consumption of those resources will result in a highermaximum speed of the emulated interface.Due to the restricted performance of an 8 bit microcontroller a pin compatible solution isprovided only; the internal register based programming interface is replaced by a set ofsubroutine calls.The attached source files also contain a test shell, which demonstrates how to exchangeinformation between an on-chip HW-SSC and the emulated SW-SSC via 5 external wiresin different operation modes. It is based on the SAB C513 (Siemens 8 bit microcontroller).A table with load measurements is presented to give an indication for the fraction of CPUperformance required by software for emulating the SSC.
标签： synchronous Emulating serial
上传时间： 2014-01-31
上传用户：z1191176801
USB接口控制器参考设计,xilinx提供VHDL代码 usb xilinx vhdl ; This program is free software; you can redistribute it and/or modify ; it under the terms of the GNU General Public License as published by ; the Free Software Foundation; either version 2 of the License, or ; (at your option) any later version. ; ; This program is distributed in the hope that it will be useful, ; but WITHOUT ANY WARRANTY; without even the implied warranty of ; MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ; GNU General Public License for more details. ; ; You should have received a copy of the GNU General Public License ; along with this program; if not, write to the Free Software ; Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
上传时间： 2013-10-12
上传用户：windgate
The Maxim Integrated 71M6541-DB REV 3.0 Demo Board is a demonstration board for evaluating the 71M6541 device for single-phase electronic energy metering applications in conjunction with the Remote Sensor Inter-face. It incorporates a 71M6541 integrated circuit, a 71M6601 Remote Interface IC, peripheral circuitry such as a serial EEPROM, emulator port, and on-board power supply. A serial to USB converter allows communication to a PC through a USB port. The Demo Board allows the evaluation of the 71M6541 energy meter chip for measurement accuracy and overall system use.
上传时间： 2013-11-06
上传用户：雨出惊人love
