这个使用usb的avr jtag ice的例子,同样有sch和pcb
上传时间： 2013-12-22
上传用户：日光微澜
USB下载线的vhdl程序,实现USB协议和JTAG接口的转换,用状态机实现的
上传时间： 2014-01-11
上传用户：mikesering
用verilog编写的USB下载线程序 实现USB协议和JTAG接口的数据转换实现状态机
上传时间： 2013-12-12
上传用户：洛木卓
用verilog编写的USB下载线程序 实现USB协议和JTAG接口的数据转换实现状态机。
上传时间： 2013-12-25
上传用户：chenbhdt
usb to jtag interface circuit
标签： interface circuit jtag usb
上传时间： 2014-01-20
上传用户：liuchee
ARM微处理器的应用已经遍及工业控制、消费类电子产品、通信系统、网络系统、无线系统等各类产品市场，占领了32位RISC微处理器75％以上的市场份额。 本文设计的基于JTAG接口的ARM编程器，以ARM微处理器作为CPU，利用其JTAG接口对Flash在线编程的技术，给以ARM为内核的应用板(数控系统硬件平台)进行快速软件升级。在分析相关技术的基础上，给出了系统的总体设计方案，设计了系统的硬件和软件。 首先详细分析了JTAG技术、USB技术和Modem通信原理。编程器以USB口和RS-232口作为通信接口，以JTAG接口作为调试接口和编程接口。 其次，在分析编程器需求的基础上，给出了系统的总体设计方案，选择了主要的部件。系统硬件的核心部件采用了Philips LPC2144ARM芯片，扩展了JTAG接口、USB接口、Modem接口，同时又构造出了一个JTAG接口。该芯片具有SPI总线，采用与SPI兼容的外部Flash作为存储器。编程器软件在ADS集成开发环境下开发调试。 最后，对编程器技术实现上的不足作了分析和编程器设计的不完善之处作了总结，并对编程器的发展趋势作了探讨和展望。
上传时间： 2013-06-16
上传用户：mylinden
H-JTAG USB仿真器是一款高速USB接口仿真器。仿真器采用USB接口供电，无需外接电源。支持10K~15MHZ的JTAG时钟,，可提供最高可达750 KB/S的下载速度与最高可达550 KB/S读取速度。与H-JTAG/H-FLASHER配合使用，可以实现高速调试与下载。该仿真器灵活，高效，稳定性好，能够全面满足用户的需求
标签： H-JTAG
上传时间： 2013-04-24
上传用户：q123321
·刚制作成功的AVR仿真器,加了CP2102当USB,又加了244芯片,用起来很爽原理图：AVR-JTAG-USB_99SE USB驱动：USB驱动程序CP2102 烧录文件：flash.rar 烧录文件：eeprom.rar
上传时间： 2013-06-15
上传用户：RedLeaves1995
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 MicrocontrollerCore. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementationof the USB hardware directly on the chip, complying with the Universal Serial Bus Specification, Revision1.1.This application note describes a demonstration program that has been written for the DK3200 hardwaredemonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to workwith the device, using the HID class as a ready-made device driver for the USB connection.IN-APPLICATION-PROGRAMMING (IAP) AND IN-SYSTEM-PROGRAMMING (ISP)Since the μPSD contains two independent Flash memory arrays, the Micro Controller Unit (MCU) can executecode from one memory while erasing and programming the other. Product firmware updates in thefield can be reliably performed over any communication channel (such as CAN, Ethernet, UART, J1850)using this unique architecture. For In-Application-Programming (IAP), all code is updated through theMCU. The main advantage for the user is that the firmware can be updated remotely. The target applicationruns and takes care on its own program code and data memory.IAP is not the only method to program the firmware in μPSD devices. They can also be programmed usingIn-System-Programming (ISP). A IEEE1149.1-compliant JTAG interface is included on the μPSD. Withthis, the entire device can be rapidly programmed while soldered to the circuit board (Main Flash memory,Secondary Boot Flash memory, the PLD, and all configuration areas). This requires no MCU participation.The MCU is completely bypassed. So, the μPSD can be programmed or reprogrammed any time, anywhere, even when completely uncommitted.Both methods take place with the device in its normal hardware environment, soldered to a printed circuitboard. The IAP method cannot be used without previous use of ISP, because IAP utilizes a small amountof resident code to receive the service commands, and to perform the desired operations.
标签： Demonstration 3200 USB for
上传时间： 2014-02-27
上传用户：zhangzhenyu
本文探讨如何透过USB来设定各种采用FPGA的系统与实现现场升级的弹性。这种方法还可用来取代热门的JTAG组态介面，让用户不再需要用到机板上分立的JTAG连结器，就能降低成本并减少占用电路板的空间。
上传时间： 2014-06-11
上传用户：liu999666
