U 盘作为一种便利的存储设备，可以应用于嵌入式系统中，其应用的基础就是对Linux 的USB Mass Storage 驱动的裁剪，以获得所需的简化的驱动程序。分析了Linux 下的USB mass storage 协议，简化系统中所不需要的代码，使其仅支持基于Bulk-Only 传输模式下的ATAPI 协议的存储设备，从而使嵌入式系统更加精简，对USB mass storage 驱动程序进行了裁剪。经过裁剪的USB Mass Storage 驱动程序移植到三星公司的QT2410E 开发板上并取得成功。
上传时间： 2013-11-23
上传用户：wfl_yy
中文版《天线理论与设计》R.S.Elliott 著 王茂光等译
上传时间： 2013-11-23
上传用户：zwei41
Single-Ended and Differential S-Parameters Differential circuits have been important incommunication systems for many years. In the past,differential communication circuits operated at lowfrequencies, where they could be designed andanalyzed using lumped-element models andtechniques. With the frequency of operationincreasing beyond 1GHz, and above 1Gbps fordigital communications, this lumped-elementapproach is no longer valid, because the physicalsize of the circuit approaches the size of awavelength.Distributed models and analysis techniques are nowused instead of lumped-element techniques.Scattering parameters, or S-parameters, have beendeveloped for this purpose [1]. These S-parametersare defined for single-ended networks. S-parameterscan be used to describe differential networks, but astrict definition was not developed until Bockelmanand others addressed this issue [2]. Bockelman’swork also included a study on how to adapt single-ended S-parameters for use with differential circuits[2]. This adaptation, called “mixed-mode S-parameters,” addresses differential and common-mode operation, as well as the conversion betweenthe two modes of operation.This application note will explain the use of single-ended and mixed-mode S-parameters, and the basicconcepts of microwave measurement calibration.
上传时间： 2014-03-25
上传用户：yyyyyyyyyy
用二端口S-参数来表征差分电路的特性■ Sam Belkin差分电路结构因其更好的增益，二阶线性度，突出的抗杂散响应以及抗躁声性能而越来越多地被人们采用。这种电路结构通常需要一个与单端电路相连接的界面，而这个界面常常是采用“巴伦”器件（Balun），这种巴伦器件提供了平衡结构-到-不平衡结构的转换功能。要通过直接测量的方式来表征平衡电路特性的话，通常需要使用昂贵的四端口矢量网络分析仪。射频应用工程师还需要确定幅值和相位的不平衡是如何影响差分电路性能的。遗憾的是，在射频技术文献中，很难找到一种能表征电路特性以及衡量不平衡结构所产生影响的好的评估方法。这篇文章的目的就是要帮助射频应用工程师们通过使用常规的单端二端口矢量网络分析仪来准确可靠地解决作为他们日常工作的差分电路特性的测量问题。本文介绍了一些用来表征差分电路特性的实用和有效的方法， 特别是差分电压，共模抑制（CMRR），插入损耗以及基于二端口S-参数的差分阻抗。差分和共模信号在差分电路中有两种主要的信号类型：差分模式或差分电压Vdiff 和共模电压Vcm（见图2）。它们各自的定义如下[1]：• 差分信号是施加在平衡的3 端子系统中未接地的两个端子之上的• 共模信号是相等地施加在平衡放大器或其它差分器件的未接地的端子之上。
上传时间： 2013-10-14
上传用户：叶山豪
Agilent AN 154 S-Parameter Design Application Note S参数的设计与应用 The need for new high-frequency, solid-state circuitdesign techniques has been recognized both by microwaveengineers and circuit designers. These engineersare being asked to design solid state circuitsthat will operate at higher and higher frequencies.The development of microwave transistors andAgilent Technologies’ network analysis instrumentationsystems that permit complete network characterizationin the microwave frequency rangehave greatly assisted these engineers in their work.The Agilent Microwave Division’s lab staff hasdeveloped a high frequency circuit design seminarto assist their counterparts in R&D labs throughoutthe world. This seminar has been presentedin a number of locations in the United States andEurope.From the experience gained in presenting this originalseminar, we have developed a four-part videotape, S-Parameter Design Seminar. While the technologyof high frequency circuit design is everchanging, the concepts upon which this technologyhas been built are relatively invariant.The content of the S-Parameter Design Seminar isas follows:
标签： S参数
上传时间： 2013-12-19
上传用户：aa54
s参数计算器,S11,S12,S22,S21的参数，一算变知，非常方便。
上传时间： 2013-11-21
上传用户：432234
嵌入式ARM9系列处理器支持U-Boot从Nor FLASH或者Nand FLASH启动，也支持U-Boot直接下载到内存中调试运行，根据U-Boot在不同启动设备上的差异，添加Nand FLASH读写驱动和判别启动位置程序，使U-Boot支持自动识别启动。在基于S3C2440的硬件平台上验证通过，并正确引导了Linux内核。
上传时间： 2013-10-16
上传用户：yanming8525826
u C / O S 是一种公开源代码、结构小巧、具有可剥夺实时内核的实时操作系统，主要用于嵌入式应用设计，本内容主要包含了多任务操作系统的源代码
上传时间： 2013-10-13
上传用户：sun_pro12580
U盘读写模块资料
上传时间： 2013-11-03
上传用户：18707733937
买的开发板上带的52个应用于实物的程序，希望对大家有帮助
上传时间： 2013-11-04
上传用户：xymbian
