Under the Energy Independence and Security Act of 2007 (EISA), the National Institute of Standards and Technology (NIST) was assigned “primary responsibility to coordinate development of a framework that includes protocols and model standards for information management to achieve interoperability of Smart Grid devices and systems…” [EISA Section 1305]. 35 This responsibility comes at a time when the electric power grid and electric power industry are undergoing the most dramatic TransforMATion in many decades. Very significant investments are being made by industry and the federal government to modernize the power grid. To realize the full benefits of these investments—and the continued investments forecast for the coming decades—there is a continued need to establish effective smart grid 36 standards and protocols for interoperability.
标签： Framework Roadmap NIST and
上传时间： 2020-06-07
上传用户：shancjb
Power Electronics is one of modern and key technologies in Electrical and Electronics Engineering for green power, sustainable energy systems, and smart grids. Especially, the TransforMATion of existing electric power systems into smart grids is currently a global trend. The gradual increase of distributed generators in smart grids indicates a wide and important role for power electronic converters in the electric power system, also with the increased use of power electronics devices (nonlinear loads) and motor loadings, low cost, low-loss and high-performance shunt current quality compensators are highly demanded by power customers to solve current quality problems caused by those loadings.
标签： Electronics Parallel Filters Power
上传时间： 2020-06-07
上传用户：shancjb
以仓库智能改造为背景,主要介绍单片机和上位机之间通信网络和通信协议的选择,MODBUS协议通信指令和功能码使用,重点阐述了基于RS-485总线的MODBUS通信协议在上位机和单片机之间的串行通信,实现上位机对单片机设备的远程控制和信息采集的功能。Based on the intelligent warehouse TransforMATion as the background,mainly introduces between MCU and PC communication network and the choice of communication protocol,instruction and the function code using the MODBUS protocol communication,expounds the MODBUS communication protocol based on RS-485 bus serial communication between PC and single chip microcomputer,PC remote control of single chip computer equipment and the function of information collection.
上传时间： 2022-03-26
上传用户：tigerwxf1
基于DSP28035的高速永磁无刷直流电机驱动系统，包括论文和软硬设计资料。摘要参赛作品为基于DSP28035的高速永磁无刷直流电机驱动系统。该系统以一台额定转速60 krpm的高速永磁无刷直流电机、交错并联的Buck电路以及全桥电路为硬件平台，以DSP28035为控制核心，实现了调压调速功能和基于坐标变换的无位置传感器新技术。为实现该系统要求，本作品充分利用了DSP28035的资源例如：CLA模块，模拟比较器、HPWM模块以及AD转换模块等。AbstractThis work is the drive system for a high speed permanent magnet burshless dc motor based on DSP28035. The hardware platform consists of a BLDC motor(rated speed is 60000rpm), a Buck circuit and an inverter. Under the control of DSP28035, this system can achieve the goal of adjusting the motor’s speed with voltage and the function of sensorless control based on the coordinate TransforMATion. By making full use of resources of the core, such as CLA, analog comparator, HPWM and AD converters, the whole system can meet the requirements.1 引言高速永磁无刷直流电机驱动系统由于基波频率较高（一般在1kHZ以上），利用逆变桥斩波进行调速的控制方式通常会受到开关管开关频率的限制，因此该系统多采用三相全桥前级加Buck电路进承担调压调速的功能，而三相全桥主要承担逻辑换相的功能。然而，传统Buck电路所需电感的体积较大，增加了系统的体积，降低了系统的功率密度。
上传时间： 2022-05-08
上传用户：bluedrops
