This document provides practical, common guidelines for incorporating PCI Express interconnect layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10- layer or more server baseboard designs. Guidelines and constraints in this document are intended for use on both baseboard and add-in card PCB designs. This includes interconnects between PCI Express devices located on the same baseboard (chip-to-chip routing) and interconnects between a PCI Express device located “down” on the baseboard and a device located “up” on an add-in card attached Through a connector. This document is intended to cover all major components of the physical interconnect including design guidelines for the PCB traces, vias and AC coupling capacitors, as well as add-in card edge-finger and connector considerations. The intent of the guidelines and examples is to help ensure that good high-speed signal design practices are used and that the timing/jitter and loss/attenuation budgets can also be met from end-to-end across the PCI Express interconnect. However, while general physical guidelines and suggestions are given, they may not necessarily guarantee adequate performance of the interconnect for all layouts and implementations. Therefore, designers should consider modeling and simulation of the interconnect in order to ensure compliance to all applicable specifications. The document is composed of two main sections. The first section provides an overview of general topology and interconnect guidelines. The second section concentrates on physical layout constraints where bulleted items at the beginning of a topic highlight important constraints, while the narrative that follows offers additional insight.
上传时间： 2013-10-15
上传用户：busterman
A light-emitting diode (LED) is a semiconductor device that emits narrow-spectrum incoherent light when forward-biased.The color of the emitted light depends on the chemical composition of the semiconductor material used, and can benear-ultraviolet, visible or infrared. LEDs are more prevalent today than ever before, replacing traditional incandescent andfluorescent bulbs in many lighting applications. Incandescents use a heated filament, are subject to breakage and burnoutand operate at a luminous efficiency of 2% to 4%. Fluorescents are more efficient, at 7% to 12%, but require highdrive voltage and contain mercury, a toxic substance that may be eventually banned in certain countries. LEDs, however,produce light directly Through electroluminescence, operate at low voltage and can deliver over 20% luminous efficiency.
上传时间： 2013-11-07
上传用户：xiaoyuer
Abstract: There are many things to consider when designing a power supply for a field-programmablegate array (FPGA). These include (but are not limited to) the high number of voltage rails, and thediffering requirements for both sequencing/tracking and the voltage ripple limits. This application noteexplains these and other power-supply considerations that an engineer must think Through whendesigning a power supply for an FPGA.
上传时间： 2013-11-12
上传用户：金苑科技
锁定放大是微弱信号检测的重要手段。基于相关检测理论，利用开关电容的开关实现锁定放大器中乘法器的功能，提出开关电容和积分器相结合以实现相关检测的方法，并设计出一种锁定放大器。该锁定放大器将微弱信号转化为与之相关的方波，通过后续电路得到正比于被测信号的直流电平，为后续采集处理提供方便。测量数据表明锁定放大器前级可将10-6 A的电流转换为10-1 V的电压，后级通过带通滤波器级联可将信号放大1×105倍。该方法在降低噪声的同时，可对微弱信号进行放大，线性度较高、稳定性较好。 Abstract: Lock-in Amplifying（LIA）is one of important means for weak signal detection. Based on cross-correlation detection theory， switch in the swithched capacitor was used as multiplier of LIA， and a new method of correlation detection was proposed combining swithched capacitor with integrator. A kind of LIA was designed which can convert the weak signal to square-wave， then DC proportional to measured signal was obtained Through follow-up conditioning circuit， providing convenience for signal acquisition and processing. The measured data shows that the electric current（10-6 A） can be changed into voltage（10-1 V） by LIA， and the signal is magnified 1×105 times by cascade band-pass filter. The noise is suppressed and the weak signal is amplified. It has the advantages of good linearity and stability.
上传时间： 2013-11-29
上传用户：黑漆漆
The latest generation of Texas Instruments (TI) boardmountedpower modules utilizes a pin interconnect technologythat improves surface-mount manufacturability.These modules are produced as a double-sided surfacemount(DSSMT) subassembly, yielding a case-less constructionwith subcomponents located on both sides of theprinted circuit board (PCB). Products produced in theDSSMT outline use the latest high-efficiency topologiesand magnetic-component packaging. This providescustomers with a high-efficiency, ready-to-use switchingpower module in a compact, space-saving package. Bothnonisolated point-of-load (POL) switching regulators andthe isolated dc/dc converter modules are being producedin the DSSMT outline.TI’s plug-in power product line offers power modules inboth Through-hole and surface-mount packages. The surfacemountmodules produced in the DSSMT outline use asolid copper interconnect with an integral solder ball fortheir
上传时间： 2013-10-10
上传用户：1184599859
数字控制的交流调速系统所选用的微处理器、功率器件及产生PWM波的方法是影响交流调速系统性能好坏的直接因素。在介绍了正弦脉宽调制(SPWM)技术的基础上，设计了一种以8098单片机作为控制器，以智能功率模块IPM为开关器件的变频调速系统。通过软件编程，产生正弦脉冲宽度调制波形来控制绝缘栅双极晶体管的导通和关断，从而达到控制异步电动机转速的目的。实验结果表明，该系统可调频率调电压，稳定度高，调速范围宽，具有较强的实用价值 Abstract: AC variable speed with digital control systems used microprocessors， power devices and generate PWM wave is the direct factors of affecting the performance AC speed regulation system. On the basis of introducing the sinusoidal pulse width modulation (SPWM) technology，this paper designed variable speed system which used 8098 as a controller， intelligent power module IPM as switching device. Through software programming， resulting in sinusoidal pulse width modulation waveform to control the insulated gate bipolar transistor turn on and off， so as to achieve the purpose of speed control of induction motors. Experimental results show that the system can adjust frequency modulation voltage， high stability， wide speed range， has a strong practical value.
上传时间： 2013-11-14
上传用户：ynwbosss
利用单片机具有的智能程序控制的特点，设计了基于STC89C52单片机的"二极管特性测试器"，可对二极管一般特性进行快速测试。通过稳定线性电流源给二极管加载恒定电流，然后由高精度模数转换器测试其压降，以此为基础可判断二极管好坏、检测二极管极性和测试二极管伏安特性等，避免了用万用表测试只能测得极性而不知其特性这一缺点。可用于电子设计制作过程中对二极管进行快速测试，以确定被测二极管是否满足电路的设计要求。 Abstract: By making good use of the intelligent control function of the Micro Controller Unit (MCU)， the diode trait tester was designed based on the STC89C52，which could be used to test the trait of a diode rapidly. By loading constant current to diode Through the stable linear current source， and measuring the voltage drop of the diode by high-precision analogue-to-digital converter (ADC)， it can judge whether the diode is good or not， distinguish the polarity of the diode， and test the trait that the diode， which can avoid the fault of using a multimeter can only measure the polarity but not the trait. This device can be used to test the trait of a diode quickly，and to make sure that whether a diode can be used in the electronic design or not.
上传时间： 2013-11-13
上传用户：assef
针对科研实验中对拉压千斤顶加载过程控制的需要，采用ATmega128单片机控制步进电机进而实现对执行系统的电动泵站实行自动控制。对力和位移的数据采集与处理及用步进电机控制电动泵站手柄的技术细节作了重点描述。通过单片机的A/D变换器对AMP放大模块采集的电桥信号作量化处理，千斤顶的操控手柄位置依电动油泵阀门开启的方向和大小作若干定位，单片机根据力或位移传感器信号，实时控制步进电机驱动手柄旋转到相应操控位置。 Abstract: This article describes the use of ATmega128 AVR microcontroller series of DBS electric pumping stations and QF100/200 separate twoway hydraulic jack to automate the process of manipulating the work of the technical content. Articles on force and displacement data acquisition and processing， and stepper motor control electric pump with the handle of the key technical details were described. Through the MCU’s A / D converter module is collected on the AMP amplification quantify the signal bridge， jack handle position control valve opening according to the direction of electric pumps for a number of positioning and size of the microcontroller based on force or displacement sensor signals， real-time control stepper motor drive control handle rotate to the appropriate location.
上传时间： 2014-01-16
上传用户：hasan2015
便携式信号采集在机器健康诊断系统中有较高的应用价值。机器健康诊断的信号特点是包括低频信号。本文研究是为了实现简易而且低成本的低频便携式信号采集。以Microchip公司单片机PIC18F1320为核心设计信号采集电路，实现了信号的采集和保存。系统采用串行电可擦除芯片24LC32A保存数据，经过有线通信，信号数据由串行口通过MAX232芯片输送到微型计算机接收和保存，最后绘制出信号波形。 微型计算机程序采用Visual Basic编程。研究成功采样频率为3 kHz的复杂信号，证明该方案符合设计要求。 Abstract: Portable signal acquisition is useful in machine health monitoring systems. The signal characteristics of machine health monitoring includes low frequency signals. The goal of this study is to realize simple, inexpensive and portable low frequency signal sampling. This paper provides the project of signal acquisition system design based on PIC18F1320 microcontroller manufactured by the Microchip Technology Incorporation to achieve signal sampling and storage. The system adopted EEPROM 24LC32A to store the signal data. The microcomputer received data via wired link with the MAX232 IC Through the serial port. The microcomputer program, programmed in Visual Basic, received the data, stored it and plotted the signal. The study successfully samples 3kHz complicated signals and thus meets the design requirement.
上传时间： 2013-11-19
上传用户：moerwang
为解决电致变色器件的颜色变化受外界环境颜色控制的问题，设计了一种基于单片机的便携式颜色自适应识别电路。与传统颜色识别电路相比较，该电路利用数字式的颜色传感器来获取外界环境颜色，产生的数字颜色信号易于单片机进行处理。在电路中，下位机部分主要负责获取电致变色器件变色参数及控制电致变色器件的颜色变化;而上位机部分主要负责把下位机获取的电致变色器件变色参数进行电压到颜色的曲线拟合，并通过蓝牙通信把拟合曲线参数传递给下位机。结果表明，该电路能自动根据环境颜色提供-4~4 V范围步进为0.1 V的电压来驱动电致变色器件的颜色显示，与传统的颜色识别电路设计相比，识别的精度和速度都得到了明显改善。 Abstract: In this paper， a portable adaptive circuit for color identification(PACCI) based on MCU was designed. Compared to the traditional color identification circuit， the PACCI adopts digital sensor to detect the color data from external environment and further generate digital color data， which can be processed easily by MCU. In PACCI， the slave is mainly responsible for detecting the color parameters of the corresponding elcreochromic device and further driving it. For the master， which is mainly responsible for the color curve fitting based on the parameters of the electrochromic device， and transmits the fitting parameters to the slave Through the bluetooth device. The results show that the PACCI can provide the basis voltage range from -4V to 4V automatically based on the colors of external environment with step as 0.1V to drive the corresponding electrochromic device. Compared to the traditional color recognition circuit， the recognition accuracy and speed of PACCI have been improved significantly.
上传时间： 2013-11-09
上传用户：franktu
