The SP2526A device is a dual +3.0V to +5.5V USB Supervisory Power Control Switch ideal for self-powered and bus-powered Universal Serial Bus (USB) applications. Each switch has low on-resistance (110mΩ typical) and can supply 500mA minimum. The fault currents are limited to 1.0A typical and the flag output pin for each switch is available to indicate fault conditions to the USB controller. The Thermal shutdown feature will prevent damage to the device when subjected to excessive current loads. The undervoltage lockout feature will ensure that the device will remain off unless there is a valid input voltage present.
标签： High-Side Switch Power Dual USB
上传时间： 2019-03-06
上传用户：bhitr
The AZ1117 is a series of low dropout three-terminal regulators with a dropout of 1.15V at 1A output current. The AZ1117 series provides current limiting and Thermal shutdown. Its circuit includes a trimmed bandgap reference to assure output voltage accuracy to be within 1% for 1.5V, 1.8V, 2.5V, 2.85V, 3.3V, 5.0V and adjustable versions or 2% for 1.2V version. Current limit is trimmed to ensure specified output current and controlled short-circuit current. On-chip Thermal shutdown provides protection against any combination of overload and ambient temperature that would create excessive junction temperature. The AZ1117 has an adjustable version, that can provide the output voltage from 1.25V to 12V with only 2 external resistors.
上传时间： 2019-04-11
上传用户：heaven0o0o0
This book is a result of the recent rapid advances in two related technologies: com- munications and computers. Over the past few decades, communication systems have increased in complexity to the point where system design and performance analysis can no longer be conducted without a significant level of computer sup- port. Many of the communication systems of fifty years ago were either power or noise limited. A significant degrading effect in many of these systems was Thermal noise, which was modeled using the additive Gaussian noise channel.
标签： Communication Principles Simulation Systems of
上传时间： 2020-05-31
上传用户：shancjb
The author of this textbook intends to consider all stages of the life cycle of the energy resources: extraction of mineral energy resources and mastering for power engineering renewable energy, transportation of mineral energy raw materials to the place of consumption, the conversion of primary energy sources into electrical and/or Thermal energy, transportation and distribution among the customers, and energy storage (if necessary).
标签： Engineering Electrical Current Power State
上传时间： 2020-06-07
上传用户：shancjb
A power semiconductor module is basically a power circuit of different materials assembled together using hybrid technology, such as semiconduc- tor chip attachment, wire bonding, encapsulation, etc. The materials involved cover a wide range from insulators, conductors, and semiconduc- tors to organics and inorganics. Since these materials all behave differently under various environmental, electrical, and Thermal stresses, proper selec- tion of these materials and the assembly processes are critical. In-depth knowledge of the material properties and the processing techniques is there- fore required to build a high-performance and highly reliable power module.
标签： Manufacture Electronic Modules Design Power
上传时间： 2020-06-07
上传用户：shancjb
2.7V to 5.5V input voltage Range Efficiency up to 96% 24V Boost converter with 12A switch current Limit 600KHz fixed Switching Frequency Integrated soft-start Thermal Shutdown Under voltage Lockout Support external LDO auxiliary power supply 8-Pin SOP-PP PackageAPPLICATIONSPortable Audio Amplifier Power SupplyPower BankQC 2.0/Type CWireless ChargerPOS Printer Power SupplySmall Motor Power Supply
标签： XR2981
上传时间： 2021-11-05
上传用户：
PCB的电磁兼容设计.pdfPCB Thermal resistance的分析和计算.pdf
上传时间： 2021-11-22
上传用户：bluedrops
The PW4556 series of devices are highly integrated Li-Ion and Li-Pol linear chargers targetedat small capacity battery for portable applications. It is a complete constant-current/ constantvoltage linear charger. No external sense resistor is needed, and no blocking diode is required dueto the internal MOSFET architecture. It can deliver up to 300mA of charge current (using a goodThermal PCB layout) with a final float voltage accuracy of ±1%. The charge voltage is fixed at 4.2V or4.35V, and the charge current can be programmed externally with a single resistor. The chargerfunction has high accuracy current and voltage regulation loops and charge termination
标签： pw4556
上传时间： 2022-02-11
上传用户：1208020161
PW4203 is a 4.5-22V input, 2A multi-cell synchronous Buck Li-Ion battery charger, suitable forportable application. Select pin is convenient for multi-cell charging. 800 kHz synchronous buckregulator integrates of 22V rating FETs with ultra low on- resistance to achieve high efficiency andsimple circuit design.The PW4203 is available in an 8-pin SOP package, provides a very compact system solution andgood Thermal conductance
标签： pw4203
上传时间： 2022-02-11
上传用户：
The PW4055 is a complete constant-current /constant-voltage linear charger for single cell lithiumion batteries.Its ThinSOT package and low external component count make the PW4055 ideallysuited for portable applications.Furthermore, the PW4055 is specifically designed to work within USBpower specifications.The PW4055 No external sense resistor is needed, and no blocking diode is required due to theinternal MOSFET architecture.Thermal feedback regulates the charge current to limit the dietemperature during high power operation or high ambient temperature. The charge voltage is fixedat 4.2V, and the charge current can be programmed externally with a single resistor. The PW4055automatically terminates the charge cycle when the charge current drops to 1/10th the programmedvalue after the final float voltage is reached. When the input supply (wall adapter or USB supply) isremoved, the PW4055 automatically enters a low current state, dropping the battery drain currentto less than 2µA. The PW4055 can be put into shutdown mode, reducing the supply current to 25µA.The BAT pin has a 7KV ESD(HBM) capability. Other features include charge current monitor, undervoltage lockout, automatic recharge and a status pin to indicate charge termination and the presenceof an input voltage
标签： pw4055
上传时间： 2022-02-11
上传用户：jason_vip1
