ANALOG INPUT BANDWIDTH is a measure of the frequencyat which the reconstructed output fundamental drops3 dB below its low frequency value for a full scale input. Thetest is performed with fIN equal to 100 kHz plus integer multiplesof fCLK. The input frequency at which the output is −3dB relative to the low frequency input signal is the full powerbandwidth.APERTURE JITTER is the variation in aperture delay fromsample to sample. Aperture jitter shows up as input noise.APERTURE DELAY See Sampling Delay.BOTTOM OFFSET is the difference between the input voltagethat just causes the output code to transition to the firstcode and the negative reference voltage. Bottom Offset isdefined as EOB = VZT–VRB, where VZT is the first code transitioninput voltage and VRB is the lower reference voltage.Note that this is different from the normal Zero Scale Error.CONVERSION LATENCY See PIPELINE DELAY.CONVERSION TIME is the time required for a completemeasurement by an analog-to-digital converter. Since theConversion Time does not include acquisition time, multiplexerset up time, or other elements of a complete conversioncycle, the conversion time may be less than theThroughput Time.DC COMMON-MODE ERROR is a specification which appliesto ADCs with differential inputs. It is the change in theoutput code that occurs when the analog voltages on the twoinputs are changed by an equal amount. It is usually expressed in LSBs.
上传时间： 2013-11-12
上传用户：pans0ul
Radio Frequency Integrated Circuit Design I enjoyed reading this book for a number of reasons. One reason is that itaddresses high-speed analog design in the context of microwave issues. This isan advanced-level book, which should follow courses in basic circuits andtransmission lines. Most analog integrated circuit designers in the past workedon applications at low enough frequency that microwave issues did not arise.As a consequence, they were adept at lumped parameter circuits and often notcomfortable with circuits where waves travel in space. However, in order todesign radio frequency (RF) communications integrated circuits (IC) in thegigahertz range, one must deal with transmission lines at chip interfaces andwhere interconnections on chip are far apart. Also, impedance matching isaddressed, which is a topic that arises most often in microwave circuits. In mycareer, there has been a gap in comprehension between analog low-frequencydesigners and microwave designers. Often, similar issues were dealt with in twodifferent languages. Although this book is more firmly based in lumped-elementanalog circuit design, it is nice to see that microwave knowledge is brought inwhere necessary.Too many analog circuit books in the past have concentrated first on thecircuit side rather than on basic theory behind their application in communications.The circuits usually used have evolved through experience, without asatisfying intellectual theme in describing them. Why a given circuit works bestcan be subtle, and often these circuits are chosen only through experience. Forthis reason, I am happy that the book begins first with topics that require anintellectual approach—noise, linearity and filtering, and technology issues. Iam particularly happy with how linearity is introduced (power series). In therest of the book it is then shown, with specific circuits and numerical examples,how linearity and noise issues arise.
上传时间： 2014-12-23
上传用户：han_zh
This document provides practical, common guidelines for incorporating PCI Express interconnect layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10- layer or more server baseboard designs. Guidelines and constraints in this document are intended for use on both baseboard and add-in card PCB designs. This includes interconnects between PCI Express devices located on the same baseboard (chip-to-chip routing) and interconnects between a PCI Express device located “down” on the baseboard and a device located “up” on an add-in card attached through a connector. This document is intended to cover all major components of the physical interconnect including design guidelines for the PCB traces, vias and AC coupling capacitors, as well as add-in card edge-finger and connector considerations. The intent of the guidelines and examples is to help ensure that good high-speed signal design practices are used and that the timing/jitter and loss/attenuation budgets can also be met from end-to-end across the PCI Express interconnect. However, while general physical guidelines and suggestions are given, they may not necessarily guarantee adequate performance of the interconnect for all layouts and implementations. Therefore, designers should consider modeling and simulation of the interconnect in order to ensure compliance to all applicable specifications. The document is composed of two main sections. The first section provides an overview of general topology and interconnect guidelines. The second section concentrates on physical layout constraints where bulleted items at the beginning of a topic highlight important constraints, while the narrative that follows offers additional insight.
上传时间： 2013-10-15
上传用户：busterman
Abstract: The rapid build out of today's smart grid raises a number of security questions. In this article,we review two recent well-documented security breaches and a report of a security gap. These situationsinclude a 2009 smart-meter hack in Puerto Rico; a 2012 password discovery in grid distributionequipment; and insecure storage of a private key in distribution automation equipment. For each of theseattacks, we examine the breach, the potential threat, and secure silicon methods that, as part of acomplete security strategy, can help thwart the attacks.
上传时间： 2013-10-27
上传用户：tecman
Abstract: This document details the Lakewood (MAXREFDES7#) subsystem reference design, a 3.3V input, ±12V (±15V) output, isolated power supply. The Lakewood reference design includes a 3W primary-side transformer H-bridge driver for isolated supplies, and two wide input range and adjustable output low-dropout linear regulators (LDOs). Test results and hardware files are included.
标签： MAXREFDES Lakewood Isolated Output
上传时间： 2013-11-02
上传用户：fengzimili
Abstract: Uses the MAX641 switching controller and an external discrete charge pump to step up the input voltage. This circuitcan service low loads and is efficient when the output is two, three, four times the input voltage. Adding the MAX627 MOSdriver can further increase the output current capability.
上传时间： 2013-11-15
上传用户：zwei41
In this paper, two types of MMIC voltage controlled oscillators have been successfully demonstrated. The first chip with single tuning diode shows the excellent tuning linearity. The second chip with two tuning diodes can improve the tuning bandwidth.
上传时间： 2013-10-17
上传用户：xjz632
Linear Technology offers a variety of devices that simplifyconverting power from a USB cable, but the LTC®3455represents the highest level of functional integration yet. The LTC3455 seamlessly manages power flowbetween an AC adapter, USB cable and Li-ion battery,while complying with USB power standards, all from a4mm × 4mm QFN package. In addtion, two high efficiencysynchronous buck converters generate low voltage railswhich most USB-powered peripherals require. TheLTC3455 also provides power-on reset signals for themicroprocessor, a Hot SwapTM output for poweringmemory cards as well as an uncommitted gain blocksuitable for use as a low-battery comparator or an LDOcontroller. The PCB real estate required for the entire USBpower control circuit and two DC/DC converters is only225mm2.
上传时间： 2013-11-02
上传用户：名爵少年
The MAX14885E, a 2:2 VGA switch, connects a VGA source to a VGA monitor. To ease direct connection to graphics controllers orthe ASIC, the MAX14885E has two supplies: VCC, a 5V ±5% supply, drives the VGA side interface; and the VL supply sets the logicswitching thresholds on the digital input pins (EN, S00, S01, S10, S11, SHA, SHB, SVA, and SVB). This application note documentsthe proper sequencing of the VCC and VL power supplies on power-up.
上传时间： 2013-10-23
上传用户：wuchunzhong
Although recent popular attention is focused on LithiumIon batteries, one must not forget that other batterychemistries, such as Nickel Cadmium (NiCd) and NickelMetal Hydride (NiMH) have advantages in rechargeablepower systems. Nickel-based batteries are robust, capableof high discharge rates, have good cycle life, do notrequire special protection circuitry and are less expensivethan Li-Ion. Among the two, NiMH batteries are rapidlyreplacing NiCd because of their higher capacity (40% to50% more) and the environmental concerns of the toxiccadmium contained in NiCd batteries.
上传时间： 2013-11-04
上传用户：qq10538412
